On the Temporal Effects of Mobile Blockers in Urban Millimeter-Wave Cellular Scenarios

Millimeter-wave (mmWave) propagation is known to be severely affected by the blockage of the line-of-sight (LoS) path. In contrast to microwave systems, at shorter mmWave wavelengths such blockage can be caused by human bodies, where their mobility within environment makes wireless channel alternate between the blocked and non-blocked LoS states. Following the recent 3GPP requirements on modeling the dynamic blockage as well as the temporal consistency of the channel at mmWave frequencies, in this paper a new model for predicting the state of a user in the presence of mobile blockers for representative 3GPP scenarios is developed: urban micro cell (UMi) street canyon and park/stadium/square. It is demonstrated that the blockage effects produce an alternating renewal process with exponentially distributed non-blocked intervals, and blocked durations that follow the general distribution. The following metrics are derived (i) the mean and the fraction of time spent in blocked/non-blocked state, (ii) the residual blocked/non-blocked time, and (iii) the time-dependent conditional probability of having blockage/no blockage at time t1 given that there was blockage/no blockage at time t0. The latter is a function of the arrival rate (intensity), width, and height of moving blockers, distance to the mmWave access point (AP), as well as the heights of the AP and the user device. The proposed model can be used for system-level characterization of mmWave cellular communication systems. For example, the optimal height and the maximum coverage radius of the mmWave APs are derived, while satisfying the required mean data rate constraint. The system-level simulations corroborate that the use of the proposed method considerably reduces the modeling complexity.Comment: Accepted, IEEE Transactions on Vehicular Technolog

A Simplified Cellular Automaton Model for City Traffic

We systematically investigate the effect of blockage sites in a cellular automaton model for traffic flow. Different scheduling schemes for the blockage sites are considered. None of them returns a linear relationship between the fraction of ``green'' time and the throughput. We use this information for a fast implementation of traffic in Dallas.Comment: 12 pages, 18 figures. submitted to Phys Rev

Propeller blockage research needs

The effect of mutual propeller/nacelle of fuselage interference on aircraft propulsive efficiency is studied in order to determine accurate drag levels from flight test data by accurately estimating installed thrust and drag and the resulting aircraft performance

Effects of percentage of blockage and flameholder downstream counterbores on lean combustion limits of premixed, prevaporized propane-air mixture

Lean combustion limits were determined for a premixed prevaporized propane air mixture with flat plate flame stabilizers. Experiments were conducted in a constant area flame tube combustor utilizing flameholders of varying percentages of blockage and downstream counterbores. Combustor inlet air velocity at ambient conditions was varied from 4 to 9 meters per second. Flameholders with a center hole and four half holes surrounding it were tested with 63, 73, and 85 percent blockage and counterbore diameters of 112 and 125 percent of the thru hole diameter, in addition to the no counterbore configuration. Improved stability was obtained by using counterbore flameholders and higher percentages of blockage. Increases in mixture velocity caused the equivalence ratio at blowout to increase in all cases

An investigation of combustion instability in aircraft-engine reheat systems

The principal objective of this study was to examine experimentally the effects of upstream temperature, velocity, gutter blockage, tailpipe length, and main and pilot fuel flows, on the form of combustion instability encountered in aircraft reheat systems which is sometimes referred to as 'buzz'. Tests were carried out at atmospheric pressure for upstream temperatures of between 200 and 500°C, and upstream velocities ranging from 140 to 200 ft/sec. Three values of stabilizer blockage were employed, namely 25, 30 and 35%. The tailpipe length was varied between 9 and 45 inches. Auto-correlation techniques were used in the frequency analysis of the buzz waveforms. It was found that a certain minimum tailpipe length is necessary in order to produce buzz which is then strengthened as the tailpipe length is increased. Buzz also becomes more pronounced with an increase in gas velocity but stabilizer blockage appears to have no discernible effect … [cont.]