Study and Design of a Diferentially Fed Tapered Slot Antenna Array

The results of a parametric study and design of an ultrawideband dual-polarized array of differentially-fed tapered slot antenna elements are presented. We examine arrays of bunny-ear antennas and discuss the capabilities and limitations of differential antenna technology. As we focus on radio astronomical applications, the absence of a balancing-feed circuit not only reduces the first-stage noise contribution associated to losses in the feed, but also leads to a cost reduction. Common-modes are supported by the antenna structure when a third conductor is present, such as a ground plane. We demonstrate that anomalies may occur in the differential-mode scan impedance. Knowledge of both types of scan impedances, differential and common mode, is required to properly design differential LNAs and to achieve optimal receiver sensitivity. A compromise solution is proposed based on the partial suppression of the undesired common-mode currents through a (low loss) balancing-dissipation technique. A fully steerable design up to 45?? in both principal planes is achieved

Reconfigurable Reflectarrays and Array Lenses for Dynamic Antenna Beam Control: A Review

Advances in reflectarrays and array lenses with electronic beam-forming capabilities are enabling a host of new possibilities for these high-performance, low-cost antenna architectures. This paper reviews enabling technologies and topologies of reconfigurable reflectarray and array lens designs, and surveys a range of experimental implementations and achievements that have been made in this area in recent years. The paper describes the fundamental design approaches employed in realizing reconfigurable designs, and explores advanced capabilities of these nascent architectures, such as multi-band operation, polarization manipulation, frequency agility, and amplification. Finally, the paper concludes by discussing future challenges and possibilities for these antennas.Comment: 16 pages, 12 figure

Dual-polarized 28-GHz air-filled SIW phased antenna array for next-generation cellular systems

A high-performance dual-polarized eight-element air-filled substrate-integrated-waveguide (AFSIW) cavity-backed patch antenna array is presented. The antenna operates in the [26.5-29.5] GHz band and provides a stable high data-rate wireless communication link between end-user terminals and access points in next-generation cellular systems. Its topology is carefully selected to maximize the performance of the array. In addition, by combining the AFSIW technology with a new antenna architecture, a low-profile, low-cost, stable, and high-performance array design is guaranteed. A prototype was fabricated and validated, demonstrating a wide active impedance bandwidth over ±35 o scanning range and low-cross polarization level within the entire frequency band

Microstrip Patch Antennas Fed by Substrate Integrated Waveguide

Dizertační práce je zaměřena na výzkum mikropáskových flíčkových antén a anténních řad napájených vlnovodem integrovaným do substrátu (SIW). Využitím vlnovodu integrovaného do substrátu pro napájení mikropáskové flíčkové antény dochází ke kombinaci výhodných vlastností obou struktur. Výsledkem je kompaktní anténní struktura, jejíž napájecí vedení neprodukuje parazitní záření a neovlivňuje tak vyzařovací charakteristiku antény. Práci lze z věcného hlediska rozdělit do dvou částí. První část práce (kapitola 2) je zaměřena na návrh flíčkových antén a jejich navázání na vlnovod integrovaný do substrátu. První dvě navržené flíčkové antény využívají vlnovod integrovaný do substrátu a štěrbinu nebo koaxiální sondu pro buzení lineárně polarizované vlny. Napájení koaxiální sondou je dále použito pro buzení kruhově polarizované flíčkové antény. Za účelem získání širšího pásma osového poměru je navrženo napájení flíčkové antény ve dvou bodech. Funkčnost všech anténních struktur je popsána pomocí parametrických simulací a ověřena realizací a měřením vyrobených prototypů antén. Prezentované napájecí metody představují nový způsob napájení pro mikropáskové antény využívající technologii SIW. Ve druhé části práce (kapitola 3) je pojednáno o implementaci štěrbinou napájené mikropáskové anténní struktury do malých anténních polí o velikosti 2x2 a 1x4. V případě lineární řady je uvažováno amplitudové rozložení pro optimální potlačení postranních laloků. Obě navržené anténní řady jsou ověřeny měřením a v porovnání s podobnými anténními řadami dostupnými v literatuře dosahují širšího pracovního pásma kmitočtů a vyššího zisku.The thesis deals with the research of microstrip patch antennas and antenna arrays fed by a substrate integrated waveguide (SIW). Exploiting an SIW structure for microstrip patch antenna feeding combines the benefits of both structures. The result is a compact antenna structure retaining advantageous properties of microstrip patch antennas and having a radiation characteristic non-effected by spurious radiation which is usually produced by a conventional feeding line. The thesis consists of two factual parts. The first one (Chapter 2) deals with the design of microstrip patch antennas and exploiting a substrate integrated waveguide for their feeding. The first two microstrip patch antennas exploit an SIW and a slot or a coaxial probe in order to excite a linearly-polarized wave. SIW-based probe feeding is further utilized for exciting a single- and dual-fed circularly-polarized microstrip patch. The functionality of the proposed antenna structures is described using parametric analyses and verified by measuring of fabricated prototypes. The proposed feeding methods represent a novel feeding approach for microstrip patch antennas exploiting SIW technology. The second part of the thesis (Chapter 3) deals with implementing the linearly-polarized aperture-coupled microstrip patch antenna structure fed by SIW into two small antenna arrays consisting of 2x2 and 1x4 radiators. An amplitude distribution is considered in the case of the linear antenna array for optimum suppression of side lobes. Both proposed antenna arrays are verified by measurements. Compared to similar antenna arrays available in the literature, they reach a wider operating frequency band and a higher gain.

Wideband and UWB antennas for wireless applications. A comprehensive review

A comprehensive review concerning the geometry, the manufacturing technologies, the materials, and the numerical techniques, adopted for the analysis and design of wideband and ultrawideband (UWB) antennas for wireless applications, is presented. Planar, printed, dielectric, and wearable antennas, achievable on laminate (rigid and flexible), and textile dielectric substrates are taken into account. The performances of small, low-profile, and dielectric resonator antennas are illustrated paying particular attention to the application areas concerning portable devices (mobile phones, tablets, glasses, laptops, wearable computers, etc.) and radio base stations. This information provides a guidance to the selection of the different antenna geometries in terms of bandwidth, gain, field polarization, time-domain response, dimensions, and materials useful for their realization and integration in modern communication systems

RF characteristics of the hoop column antenna for the land mobile satellite system mission

A communication system using a satellite with a 118 meter diameter quad aperture antenna to provide telephone service to mobile users remotely located from the large metropolitan areas where the telephone companies are presently implementing their cellular system is described. In this system, which is compatible with the cellular system, the mobile user communicates with the satellite at UHF frequencies. The satellite connects him at S-Band, to the existing telephone network via a base station. The results of the RF definition work for the quad aperture antenna are presented. The elements of the study requirements for the LMSS are summarized, followed by a beam topology plan which satisfies the mission requirements with a practical and realiable configuration. The geometry of the UHF antenna and its radiation characteristics are defined. The various feed alternatives, and the S-band aperture are described

Configuration study for a 30 GHz monolithic receive array, volume 1

Gregorian, Cassegrain, and single reflector systems were analyzed in configuration studies for communications satellite receive antennas. Parametric design and performance curves were generated. A preliminary design of each reflector/feed system was derived including radiating elements, beam-former network, beamsteering system, and MMIC module architecture. Performance estimates and component requirements were developed for each design. A recommended design was selected for both the scanning beam and the fixed beam case. Detailed design and performance analysis results are presented for the selected Cassegrain configurations. The final design point is characterized in detail and performance measures evaluated in terms of gain, sidelobe level, noise figure, carrier-to-interference ratio, prime power, and beamsteering. The effects of mutual coupling and excitation errors (including phase and amplitude quantization errors) are evaluated. Mechanical assembly drawings are given for the final design point. Thermal design requirements are addressed in the mechanical design

Gain-Reconfigurable Hybrid Metal-Graphene Printed Yagi Antenna for Energy Harvesting Applications

This paper presents a hybrid metal-graphene printed Yagi antenna with reconfigurable gain that operates in the 5.5-GHz band. The balun and the driven elements are made of copper, while the directors are made of graphene. The graphene acts as a tunable material in the design. By switching the conductivity of the graphene, it is achieved a similar effect to adding or subtracting directors in the antenna. Hence the gain of the printed Yagi can be easily controlled. This could be of special interest in RF energy harvesting in the design of reconfigurable harvesting elements.Universidad de Málaga. Campus de Excelencia Internacional Andalucía Tech

Portable low profile antenna at X-band

An antenna which has been conceived as a portable system for satellite communications based on the recommendations ITU-R S.580-6 and ITU-R S.465-5 for small antennas, i.e., with a diameter lower than 50 wavelengths, is introduced. It is a planar and a compact structure with a size of 40×40×2 cm. The antenna is formed by an array of 256 printed elements covering a large bandwidth (14.7%) at X-Band with a VSWR of 1.4:1. The specification includes transmission (Tx) and reception (Rx) bands simultaneously. The printed antenna has a radiation pattern with a 3dB beamwidth of 5°, over a 31dBi gain, and a dual and an interchangeable circular polarization

Genetic Algorithm Optimization of a High-Directivity Microstrip Patch Antenna Having a Rectangular Profile

A single high-directivity microstrip patch antenna (MPA) having a rectangular profile, which can substitute a linear array is proposed. It is designed by using genetic algorithms with the advantage of not requiring a feeding network. The patch fits inside an area of 2.54λ x 0.25λ, resulting in a broadside pattern with a directivity of 12 dBi and a fractional impedance bandwidth of 4%. The antenna is fabricated and the measurements are in good agreement with the simulated results. The genetic MPA provides a similar directivity as linear arrays using a corporate or series feeding, with the advantage that the genetic MPA results in more bandwidth