Skip to main content
Article thumbnail
Location of Repository

Thermal and Chemical Analysis of Fouling Phenomenon in Condensers for Cooling Tower Applications

By Xiaoxiao Wu and Lorenzo Cremaschi

Abstract

Brazed plate heat exchanges (BPHEs) and tube-in-tube heat exchangers (TTHEs) are commonly used in the refrigeration, air conditioning, and food industry as refrigerant-to-water condensers, in which refrigerant rejects heat to water circulating in cooling tower loops. These heat exchangers often suffer from severe fouling issues because as the water in the cooling tower evaporates, the mineral concentration in the remaining water increases. Once the solubility limits are reached, the minerals precipitate and deposit on the heat transfer surfaces: an undesirable yet unavoidable phenomenon. Due to the fouling deposit on the heat transfer surfaces, the thermal resistance between refrigerant and water gradually increases. The fouling resistance depends on several factors such as heat exchanger geometry, heat flux, water quality and water flow rates. The fouling factors penalize the overall effectiveness of the refrigerant condensers and thus must be properly accounted for during the equipment design. Predictions of the fouling allowances during the life service of the condenser characterize the degradation in thermal performance and provide guidelines about the maintenance and service of this type of equipment. In this work, a smooth TTHE was investigated by using a new experimental facility at Oklahoma State University. The aim was to measure the fouling resistance in real time and correlate the data with the water quality and heat flux inside the refrigeration condenser. The fouling resistance in the TTHE was observed to have asymptotic trend and the asymptotic limit was lower than that for BPHEs with soft corrugation angles and higher than that of BHPEs with hard corrugation angles operating at similar conditions. The hydraulic performance was similar as BPHEs with hard corrugation angles. The fouling deposit inside the tube-in-tube heat exchanger was further analyzed by using a CCD camera with a borescope probe and by adopting a chemical digestion process for the fouling particles inside the tubes. Fouling did not deposit uniformly inside the TTHE and it was evident that more fouling was present at the outlet section of the water side. The chemical analysis showed that more than 85% of the fouling material was CaCO3, which was expected from the chemical analysis of the water in critical saturation conditions

Topics: refrigerant condenser, tube-in-tube, BPHE, corrugation angle, mineral precipiation mass flux
Publisher: Purdue University
Year: 2012
OAI identifier: oai:docs.lib.purdue.edu:iracc-2211
Provided by: Purdue E-Pubs

Suggested articles

Citations

  1. (2007). AHRI Standard 450 - Performance Rating of Water-Cooled Refrigerant Condensers, Remote Type.
  2. (2011). Cooling water fouling resistance prediction of plate heat exchanger based on partial least-squares regression.
  3. (1976). Corrosion Inhibition of Copper by Tolyltriazole.
  4. (2012). Effect of Condensation Temperature and Water Quality on Fouling of Brazed Plate Heat Exchangers. Paper prensented at the ASHRAE winter meeting-Technical Papers,
  5. (1999). Effect of geometry and flow conditions on particulate fouling in plate heat exchangers. Heat Transfer Engineering,
  6. (2009). Effects of temperature and velocity on fouling by municipal secondary effluent in plate heat exchangers.
  7. (2000). Fouling in enhanced tubes using cooling tower water Part II: Combined particulate and precipitation fouling.
  8. (1994). Guidelines for evaluating and expressing the uncertainty of NIST measurements results.
  9. (1997). Heat mass transfer model of scaling process.
  10. (2001). Heating and Refrigeration Institute
  11. (1996). Investigation of flow and heat transfer in corrugated passages—I. Experimental results.
  12. (1997). Liquid-side fouling of heat exchangers. An integrated R D approach for conventional and novel designs.
  13. (1994). Modeling liquid-side particulate fouling in enhanced tubes.
  14. (2003). Physical water treatment for the mitigation of mineral fouling in coolingtower water applications.
  15. (1978). Prediction of Calcium Carbonate Scaling Rates.
  16. (1991). Survey of water quality and its effect on fouling in flooded water chiller evaporators. Paper presented at the ASHRAE Winter Meeting -
  17. (1936). The analytical control of anti-corrosion water treatment.
  18. (2009). The Nalco water handbook. from http://www.knovel.com/knovel2/Toc.jsp?BookID=2799
  19. (2011). Waterside fouling performance in brazed-plate-type condensers for cooling tower applications.

To submit an update or takedown request for this paper, please submit an Update/Correction/Removal Request.