18 research outputs found
Effects of Hybrid Flow Control on a Normal Shock Boundary-Layer Interaction
Hybrid flow control, a combination of micro-ramps and steady micro-jets, was experimentally investigated in the 15x15 cm Supersonic Wind Tunnel at the NASA Glenn Research Center. A central composite design of experiments method, was used to develop response surfaces for boundary-layer thickness and reversed-flow thickness, with factor variables of inter-ramp spacing, ramp height and chord length, and flow injection ratio. Boundary-layer measurements and wall static pressure data were used to understand flow separation characteristics. A limited number of profiles were measured in the corners of the tunnel to aid in understanding the three-dimensional characteristics of the flowfield
Sidewall Effects on Exact Reynolds-Stress Budgets in an Impinging Shock Wave/Boundary Layer Interaction
Large-eddy simulations are performed using wall-resolved mesh for a Mach 2.29 impinging shock wave/boundary-layer interaction. Flow conditions are based on an experiment and therefore entire span was simulated, including the two sidewalls. Mean flow comparison with the experimental data showed that the interaction was larger in the simulation. Time-series analysis of a rake of pressure probes immediately downstream of the mean reflected shock position showed a peak in weighted power spectral density occurred about , owing to a larger interaction length. Budgets of Reynolds-stress transport calculated across the span and along the corner bisector showed high degree of anisotropy. Merging of the secondary flows and separation along the corner gives rise to unstablecounter rotating vortices, which straddle the corner and grow in size. This also leads to a development of new behavior in the viscous sublayer along the corner bisector, where the pressure strain andmolecular diffusion mechanisms become prominent
Experimental Investigation of Normal Shock Boundary-Layer Interaction with Hybrid Flow Control
Hybrid flow control, a combination of micro-ramps and micro-jets, was experimentally investigated in the 15x15 cm Supersonic Wind Tunnel (SWT) at the NASA Glenn Research Center. Full factorial, a design of experiments (DOE) method, was used to develop a test matrix with variables such as inter-ramp spacing, ramp height and chord length, and micro-jet injection flow ratio. A total of 17 configurations were tested with various parameters to meet the DOE criteria. In addition to boundary-layer measurements, oil flow visualization was used to qualitatively understand shock induced flow separation characteristics. The flow visualization showed the normal shock location, size of the separation, path of the downstream moving counter-rotating vortices, and corner flow effects. The results show that hybrid flow control demonstrates promise in reducing the size of shock boundary-layer interactions and resulting flow separation by means of energizing the boundary layer
Reynolds-Stress Budgets in an Impinging Shock Wave/Boundary-Layer Interaction
Implicit large-eddy simulation (ILES) of a shock wave/boundary-layer interaction (SBLI) was performed. Comparisons with experimental data showed a sensitivity of the current prediction to the modeling of the sidewalls. This was found to be common among various computational studies in the literature where periodic boundary conditions were used in the spanwise direction, as was the case in the present work. Thus, although the experiment was quasi-two-dimensional, the present simulation was determined to be two-dimensional. Quantities present in the exact equation of the Reynolds-stress transport, i.e., production, molecular diffusion, turbulent transport, pressure diffusion, pressure strain, dissipation, and turbulent mass flux were calculated. Reynolds-stress budgets were compared with past large-eddy simulation and direct numerical simulation datasets in the undisturbed portion of the turbulent boundary layer to validate the current approach. The budgets in SBLI showed the growth in the production term for the primary normal stress and energy transfer mechanism was led by the pressure strain term in the secondary normal stresses. The pressure diffusion term, commonly assumed as negligible by turbulence model developers, was shown to be small but non-zero in the normal stress budgets, however it played a key role in the primary shear stress budget
Wind-US Code Contributions to the First AIAA Shock Boundary Layer Interaction Prediction Workshop
This report discusses the computations of a set of shock wave/turbulent boundary layer interaction (SWTBLI) test cases using the Wind-US code, as part of the 2010 American Institute of Aeronautics and Astronautics (AIAA) shock/boundary layer interaction workshop. The experiments involve supersonic flows in wind tunnels with a shock generator that directs an oblique shock wave toward the boundary layer along one of the walls of the wind tunnel. The Wind-US calculations utilized structured grid computations performed in Reynolds-averaged Navier-Stokes mode. Four turbulence models were investigated: the Spalart-Allmaras one-equation model, the Menter Baseline and Shear Stress Transport k-omega two-equation models, and an explicit algebraic stress k-omega formulation. Effects of grid resolution and upwinding scheme were also considered. The results from the CFD calculations are compared to particle image velocimetry (PIV) data from the experiments. As expected, turbulence model effects dominated the accuracy of the solutions with upwinding scheme selection indicating minimal effects
Turbulence Model Effects on RANS Simulations of the HIFiRE Flight 2 Ground Test Configurations
The Wind-US Reynolds-averaged Navier-Stokes solver was applied to the Hypersonic International Flight Research Experimentation (HIFiRE) Flight 2 scramjet ground test configuration. Two test points corresponding to flight Mach numbers of 5.9 and 8.9 were examined. The emphasis was examining turbulence model effects on the prediction of flow path pressures. Three variants of the Menter k-omega turbulence model family were investigated. These include the baseline (BSL) and shear stress transport (SST) as well as a modified SST model where the shear stress limiter was altered. Variations in the turbulent Schmidt number were also considered. Choice of turbulence model had a substantial effect on prediction of the flow path pressures. The BSL model produced the highest pressures and the SST model produced the lowest pressures. As expected, the settings for the turbulent Schmidt number also had significant effects on predicted pressures. Small values for the turbulent Schmidt number enabled more rapid mass transfer, faster combustion, and in turn higher flowpath pressures. Optimal settings for turbulence model and turbulent Schmidt number were found to be rather case dependent, as has been concluded in other scramjet investigations
Research on Supersonic Inlet Bleed
Phase I data results of the Fundamental Inlet Bleed Experiments project at NASA Glenn Research Center (GRC) are presented which include flow coefficient results for two single-hole boundary-layer bleed configurations. The bleed configurations tested are round holes at inclination angles of 90deg and 20deg both having length-to-diameter ratios of 2.0. Results were obtained at freestream Mach numbers of 1.33, 1.62, 1.98, 2.46, and 2.92 and unit Reynolds numbers of 0.984, 1.89, and 2.46 10(exp 7)/m. Approach boundary-layer data are presented for each flow condition and the flow coefficient results are compared to existing multi-hole data obtained under similar conditions. For the 90deg hole, the single and multi-hole distributions agree fairly well with the exception that under supercritical operation, the multi-hole data chokes at higher flow coefficient levels. This behavior is also observed for the 20deg hole but to a lesser extent. The 20deg hole also shows a markedly different characteristic at subcritical operation. Also presented are preliminary results of a Computational Fluid Dynamics (CFD) analysis of both configurations at the Mach 1.33 and a unit Reynolds number of 2.46 10(exp 7)/m. Comparison of the results shows the agreement to be very good
ESTIMATION OF GUGGULSTERONE-Z IN GOKSHURADI GUGGULU USING REVERSED-PHASE HIGH-PERFORMANCE LIQUID CHROMATOGRAPHY
Objective: A study was aimed to estimate guggulsterone-Z (GZ) in Gokshuradi Guggulu (GG).Methods: An analytical method was developed and validated using Waters Alliance high-performance liquid chromatography system (Empower software), equipped with photodiode array detector. Separation was achieved using Phenomenex, C-18 (250 mm×4.6 mm, 5 μ) column. Mobile phase consisted of acetonitrile:water (70:30,v/v). Flow rate was set to 1 ml/min and detection was performed at 251 nm.Results and Discussion: Validation parameters such as linearity, precision, accuracy, limit of detection, limit of quantification, and robustness were performed. Amount of GZ was estimated using linearity equation.Conclusion: GG was found to contain 0.815±0.03 g% w/w GZ. Validated method may be used as one of the parameters to standardize the formulation
Numerical Simulation of Vitiation Effects on a Hydrogen-Fueled Dual-Mode Scramjet
The Wind-US computational fluid dynamics (CFD) flow solver was used to simulate dual-mode direct-connect ramjet/scramjet engine flowpath tests conducted in the University of Virginia (UVa) Supersonic Combustion Facility (SCF). The objective was to develop a computational capability within Wind-US to aid current hypersonic research and provide insight to flow as well as chemistry details that are not resolved by instruments available. Computational results are compared with experimental data to validate the accuracy of the numerical modeling. These results include two fuel-off non-reacting and eight fuel-on reacting cases with different equivalence ratios, split between one set with a clean (non-vitiated) air supply and the other set with a vitiated air supply (12 percent H2O vapor). The Peters and Rogg hydrogen-air chemical kinetics model was selected for the scramjet simulations. A limited sensitivity study was done to investigate the choice of turbulence model and inviscid flux scheme and led to the selection of the k-epsilon model and Harten, Lax and van Leer (for contact waves) (HLLC) scheme for general use. Simulation results show reasonably good agreement with experimental data and the overall vitiation effects were captured
One plus two-body random matrix ensembles with parity: Density of states and parity ratios
One plus two-body embedded Gaussian orthogonal ensemble of random matrices
with parity [EGOE(1+2)-] generated by a random two-body interaction
(modeled by GOE in two particle spaces) in the presence of a mean-field, for
spinless identical fermion systems, is defined, generalizing the two-body
ensemble with parity analyzed by Papenbrock and Weidenm\"{u}ller [Phys. Rev. C
{\bf 78}, 054305 (2008)], in terms of two mixing parameters and a gap between
the positive and negative parity single particle (sp)
states. Numerical calculations are used to demonstrate, using realistic values
of the mixing parameters appropriate for some nuclei, that the EGOE(1+2)-
ensemble generates Gaussian form (with corrections) for fixed parity eigenvalue
densities (i.e. state densities). The random matrix model also generates many
features in parity ratios of state densities that are similar to those
predicted by a method based on the Fermi-gas model for nuclei. We have also
obtained, by applying the formulation due to Chang et al [Ann. Phys. (N.Y.)
{\bf 66}, 137 (1971)], a simple formula for the spectral variances defined over
fixed- spaces, where is the number of fermions in the +ve
parity sp states and is the number of fermions in the -ve parity sp
states. Similarly, using the binary correlation approximation, in the dilute
limit, we have derived expressions for the lowest two shape parameters. The
smoothed densities generated by the sum of fixed- Gaussians with
lowest two shape corrections describe the numerical results in many situations.
The model also generates preponderance of +ve parity ground states for small
values of the mixing parameters and this is a feature seen in nuclear shell
model results.Comment: 38 pages, 11 figures, 3 tables, enlarged and reorganized with
additional result