Allometry of the Duration of Flight Feather Molt in Birds

Replacement of flight feathers takes disproportionately more time for large birds than it does for small birds, because feather length increases with body size almost twice as fast as feather growth rate increases

Determination of fat content and fatty acid composition in meat and meat products after supercritical fluid extraction

Two different relatively simple, commercially available supercritical fluid extractors (SFE), Leco and Foss-Tecator, were tested for the determination of total fat content in meat and meat products. The fatty acid composition in meat and meat products was also determined after the Foss-Tecator extraction in an aliquot of the extract. Total fat was determined by weighing after the different extraction procedures and the fatty acid composition by gas chromatography after hydrolysis and methylation of the extract. The results for total fat content agreed well with results from a standard method of Schmid, Bondzynski, and Ratzlaff, which uses conventional solvent extraction. Fatty acid composition was compared with the Bligh and Dyer extraction, and showed good agreement. The average relative difference between SFE and Bligh and Dyer of all fatty acids in the sample was <3% for acids exceeding 0.5% of total fatty acid amount. The advantages of SFE over traditional methods are a much lower consumption of hazardous organic solvents and shorter extraction times. To obtain quantitative recoveries by SFE, ethanol was added to the extraction cells before extraction

Exposure to Metalworking Fluid Aerosols and Determinants of Exposure

Metalworking fluid (MWF) aerosols are associated with respiratory disorders including asthma and hypersensitivity pneumonitis. The aims of this study were to describe exposure to inhalable MWF aerosols and volatile compounds in machine shops, to estimate the influence of important determinants of exposure and to compare different sampling techniques for MWF aerosols. Personal full-shift air samples of inhalable aerosol (PAS-6 sampler) and total aerosol (open-faced sampler) were collected on operators in five medium to big-sized machine shops in three companies. The filters were analysed gravimetrically and extracted by supercritical fluid extraction for MWF aerosol and triethanolamine content. In addition, personal measurements were taken for formaldehyde and volatile compounds on adsorbent samplers. Continuous dust measurements were performed with a real-time instrument (DataRAM) during 2 h periods, using 1-min average values. In total, 95 measurements of inhalable aerosol and extracted MWF aerosols on 51 operators were conducted. Within the companies, the average exposure to inhalable aerosol ranged from 0.19 to 0.25 mg m(-3) with geometric standard deviations from 1.56 to 1.79. On average, the extracted fraction of MWF aerosol was 67% of the inhalable aerosol concentration. The exposure levels of triethanolamine, formaldehyde and volatile compounds were generally low. About 45% of the between-worker variance could be explained by use of compressed air, lack of complete enclosure of machines or grinding as cutting task. In 21 workers with continuous aerosol measurements, short-term peak exposures during 6% of the work time contributed to similar to 25% of the average concentration of inhalable MWF aerosol. Inhalable MWF aerosol concentration measured with the PAS-6 sampler was a factor 2 higher than the concentrations derived from the open-faced sampler. These findings suggest that control measures, such as full enclosure of machines and the elimination of the use of compressed air as cleaning technique, are required to reduce the exposure to MWF aerosols to levels below the expected threshold for adverse respiratory health effects

Filter-based treatment of leachate from an industrial landfill containing shredder residues of end-of-life vehicles and white goods.

A pilot plant was set up to treat leachate from an industrial landfill containing shredder residues of end-of-life vehicles and white goods. The treatment plant consisted of aeration and sedimentation steps for pre-treatment, and a filter. The plant was designed to simultaneously remove various types of pollutants. The efficiencies of pre-treatment and of the main treatment step were investigated over a period of 3 years at the landfill site. By continuous aeration of the leachate the concentrations of Fe and Mn were reduced by 55% and 49%, respectively. By prolonged sedimentation suspended solid content was noticeably reduced (72%). In the filter, consisting of a mixture of peat and carbon-containing ash as a treatment medium, very high reduction of polar organic compounds, e.g. phenol (74%), o-and p-cresol (91%), and 2,4-dimethylphenol (73%), high average reduction of metals, e.g. Pb (78%), Fe (74%), Cu (73%), Mn (56%), Sn (55%), and Zn (47%), and good average reduction of DOC (26%), Tot-N (23%) and NH(4)-N (46%) were achieved. Sixty non-polar compounds in the leachate, identified by GC-MS screening, occurred at trace level. Most of them were considerably reduced in the filter