Laser wakefield acceleration with high-power, few-cycle mid-IR lasers

The study of laser wakefield electron acceleration (LWFA) using mid-IR laser drivers is a promising path for future laser driven electron accelerators, when compared to traditional near-IR laser drivers operating at 0.8-1 mu m central wavelength (lambda(laser)), as the necessary vector potential (a(0)) for electron injection can be achieved with smaller laser powers due to the linear dependence on lambda(laser). In this work, we perform 2D PIC simulations on LWFA using few-cycle, high power (5-15 TW) laser systems with lambda(laser) ranging from 0.88 to 10 mu m. Such fewcycle systems are currently under development, aiming at Gas High Harmonics Generation applications, where the favorable lambda(2)(laser) scaling extends the range of the XUV photon energies. We keep a(0) and n(e)/n(cr) (n(e) being the plasma density and n(cr) the critical density for each lambda(laser)) as common denominators in our simulations, allowing for comparisons between drivers with different lambda(laser), with respect to the accelerated electron beam energy, charge and conversion efficiency. While the electron energies are mainly dominated by the plasma dynamics, the laser to electron beam energy conversion efficiency shows significant enhancement with longer wavelength laser drivers. (c) 2018 Elsevier B.V. All rights reserved

The FLASHForward Facility at DESY

The FLASHForward project at DESY is a pioneering plasma-wakefield acceleration experiment that aims to produce, in a few centimetres of ionised hydrogen, beams with energy of order GeV that are of quality sufficient to be used in a free-electron laser. The plasma wave will be driven by high-current density electron beams from the FLASH linear accelerator and will explore both external and internal witness-beam injection techniques. The plasma is created by ionising a gas in a gas cell with a multi-TW laser system, which can also be used to provide optical diagnostics of the plasma and electron beams due to the <30 fs synchronisation between the laser and the driving electron beam. The operation parameters of the experiment are discussed, as well as the scientific program.Comment: 19 pages, 9 figure

Development of control mechanisms for a laser wakefield accelerator-driven bremsstrahlung x-ray source for advanced radiographic imaging

A high power laser was used to accelerate electrons in a laser-driven wakefield accelerator. The high energy electrons were then used to generate an x-ray beam by passing them through a converter target. This bremsstrahlung source was characterised and used to perform penetrative imaging of industrially relevant samples. The photon spectrum had a critical energy in excess of 100 MeV and a source size smaller than the resolution of the diagnostic (≲150 µm). Simulations indicate a significantly smaller source is achievable. Variations in the x-ray source characteristics were realised through changes to the plasma and converter parameters while simulations confirm the adaptability of the source. Imaging of high areal density objects with 150 µm resolution was performed, demonstrating the unique advantages of this novel source

Expected Performance of the ATLAS Experiment - Detector, Trigger and Physics

A detailed study is presented of the expected performance of the ATLAS detector. The reconstruction of tracks, leptons, photons, missing energy and jets is investigated, together with the performance of b-tagging and the trigger. The physics potential for a variety of interesting physics processes, within the Standard Model and beyond, is examined. The study comprises a series of notes based on simulations of the detector and physics processes, with particular emphasis given to the data expected from the first years of operation of the LHC at CERN

Characterisation of a laser plasma betatron source for high resolution x-ray imaging

We report on the characterisation of an x-ray source, generated by a laser-driven plasma wakefield accelerator. The spectrum of the optimised source was consistent with an on-axis synchrotron spectrum with a critical energy of 13.8+2.2-1.9 keV and the number of photons per pulse generated above 1 keV was calculated to be 6+1.2-0.9× 10\9. The x-ray beam was used to image a resolution grid placed 37 cm from the source, which gave a measured spatial resolution of 4 µm 5 µm. The inferred emission region had a radius and length of 0.5 0.2 µm and 3.2 0.9 mm respectively. It was also observed that laser damage to the exit aperture of the gas cell led to a reduction in the accelerated electron beam charge and a corresponding reduction in x-ray flux due to the change in the plasma density profile

Application of compact laser-driven accelerator X-ray sources for industrial imaging

X-rays generated by betatron oscillations of electrons in a laser-driven plasma accelerator were characterised and applied to imaging industrial samples. With a 125TW laser, a low divergence beam with 5.2±1.7 × 107photonsmrad−2 per pulse was produced with a synchrotron spectrum with a critical energy of 14.6±1.3keV. Radiographs were obtained of a metrology test sample, battery electrodes, and a damage site in a composite material. These results demonstrate the suitability of the source for non-destructive evaluation applications. The potential for industrial implementation of plasma accelerators is discussed

Temporal feedback control of high-intensity laser pulses to optimize ultrafast heating of atomic clusters

We describe how active feedback routines can be applied at a limited repetition rate (5 Hz) to optimize high-power (> 10 TW) laser interactions with clustered gases. Optimization of x-ray production from an argon cluster jet, using a genetic algorithm, approximately doubled the measured energy through temporal modification of the 150 mJ driving laser pulse. This approach achieved an increased radiation yield through exploration of a multi-dimensional parameter space, without requiring detailed a priori knowledge of the complex cluster dynamics. The optimized laser pulses exhibited a slow rising edge to the intensity profile, which enhanced the laser energy coupling into the cluster medium, compared to the optimally compressed FWHM pulse (40 fs). Our work suggests that this technique can be more widely utilized for control of intense pulsed secondary radiation from petawatt-class laser systems

Laser wakefield acceleration with active feedback at 5 Hz

We describe the use of a genetic algorithm to apply active feedback to a laser wakefield accelerator at a higher power (10 TW) and a lower repetition rate (5 Hz) than previous work. The temporal shape of the drive laser pulse was adjusted automatically to optimize the properties of the electron beam. By changing the software configuration, different properties could be improved. This included the total accelerated charge per bunch, which was doubled, and the average electron energy, which was increased from 22 to 27 MeV. Using experimental measurements directly to provide feedback allows the system to work even when the underlying acceleration mechanisms are not fully understood, and, in fact, studying the optimized pulse shape might reveal new insights into the physical processes responsible. Our work suggests that this technique, which has already been applied with low-power lasers, can be extended to work with petawatt-class laser systems

Drons col·laboratius

La robòtica col·laborativa és senzillament robots dissenyats per dur a terme treballs de col·laboració amb els humans. Els robots col·laboratius o cobots són cada cop més utilitzats a les indústries. La robòtica col·laborativa és un dels àmbits d'actualitat en aquests moments. Però també és un dels més interessants en més d'un sentit. Com es comuniquen dos drons autònoms que col·laboren per fer una tasca? Com són aquests missatges que s'envien? Que poden fer que no podrien fer sols? Aquestes són algunes de les preguntes que ens volem respondre en aquest projecte. En aquest treball es presenta un disseny i implementació de dos drons terrestres que es comuniquen per col·laborar entre ells per resoldre una tasca.Collaborative robotics is simply robots designed to perform collaborative work with humans. Collaborative robots or cobots are increasingly used in industries. Collaborative robotics is one of the current topics now. But it is also one of the most interesting in more ways than one. How do two autonomous drones that collaborate to perform a task communicate? How are these messages sent? What can they do that they could not do alone? These are some of the questions we want to answer in this project. This work presents a design and implementation of two ground drones that communicate to collaborate with each other to solve a task.La robótica colaborativa es sencillamente robots diseñados para llevar a cabo trabajos de colaboración con los humanos. Los robots colaborativos o cobots son cada vez más utilizados en las industrias. La robótica colaborativa es uno de los ámbitos de actualidad. Pero también es uno de los más interesantes en más de un sentido. ¿Cómo se comunican drones autónomos que colaboran para hacer una tarea? ¿Cómo son estos mensajes que es envían? ¿Qué pueden hacer que no lo podrían hacer solos? Estas son algunas de las preguntas que queremos responder con este proyecto. En este trabajo se presenta un diseño e implementación de dos drones terrestres que se comunican para colaborar entre ellos para resolver una tarea