1,018 research outputs found
Comparison of carbohydrate utilization in man using indirect calorimetry and mass spectrometry after an oral load of 100 g naturally-labelled [13C]glucose
1. Carbohydrate (CHO) oxidation was measured simultaneously in a group of five normal subjects after an oral load of 100 g naturally-labelled [13C]glucose, using indirect calorimetry and mass spectrometry. 2. CHO utilization, calculated from the results of indirect calorimetry, increased 30 min after the glucose load to reach a peak at 90 min. It then decreased to reach basal values at 380 min. Cumulative total CHO oxidation at 480 min was 83±8g, and CHO oxidized above basal levels, 37±3 g. 3. Enrichment of expired carbon dioxide with 13C began at 60 min and maximum values were observed at 270 min. At 480 min, cumulative CHO oxidation measured by use of [13C]glucose was 29 g. The difference from calorimetric values can be attributed in part to the slow isotopic dilution in the glucose and bicarbonate pools. 4. Thus, approximately 30% of the glucose load was oxidized during the 8 h after its ingestion and this accounts for a significant part of the increased CHO oxidation (37 g), as measured by indirect calorimetr
Recommended from our members
Argonne National Laboratory Reports
Test data from an in-pile failure experiment of high-power LMFBR-type fuel pins in a simulated $3/s transient-overpower (TOP) accident are reported and analyzed. Major conclusions are that (1) a series of cladding ruptures during the 100-ms period preceding fuel release injected small bursts of fission gas into the flow stream; (2) gas release influenced subsequent cladding melting and fuel release (there were no measurable FCI's (fuel-coolant interactions), and all fuel motion observed by the hodoscope was very slow); (3) the predominant post-failure fuel motion appears to be radial swelling that left a spongy fuel crust on the holder wall; (4) less than 4 to 6 percent of the fuel moved axially out of the original fuel zone, and most of this froze within a 10-cm region above the original top of the fuel zone to form the outlet blockage. An inlet blockage approximately 1 cm long was formed and consisted of large interconnected void regions. Both blockages began just beyond the ends of the fuel pellets
Study of temporal pulse shape effects on W using simulations and laser heating
Transient heat pulses with triangular, square, and ELM-like temporal shapes are investigated in order to further understand how transient plasma instabilities will affect plasma facing components in tokamaks. A solution to the 1D heat equation for triangular pulses allows the peak surface temperature to be written analytically for arbitrary rise times. The solution as well as ANSYS simulations reveal that a positive ramp (maximum rise time) triangular pulse has a higher peak surface temperature by a factor of sqrt{2} compared to that from a negative ramp (rise time = 0) pulse shape with equal energy density, peak power, and pulse width. Translating the results to ITER, an ELM or disruption pulse with the shortest rise time is the most benign compared to other pulse shapes with the same peak heat flux and same energy density.</p
Dissociative recombination and electron-impact de-excitation in CH photon emission under ITER divertor-relevant plasma conditions
For understanding carbon erosion and redeposition in nuclear fusion devices,
it is important to understand the transport and chemical break-up of
hydrocarbon molecules in edge plasmas, often diagnosed by emission of the CH
A^2\Delta - X^2\Pi Ger\"o band around 430 nm. The CH A-level can be excited
either by electron-impact or by dissociative recombination (D.R.) of
hydrocarbon ions. These processes were included in the 3D Monte Carlo impurity
transport code ERO. A series of methane injection experiments was performed in
the high-density, low-temperature linear plasma generator Pilot-PSI, and
simulated emission intensity profiles were benchmarked against these
experiments. It was confirmed that excitation by D.R. dominates at T_e < 1.5
eV. The results indicate that the fraction of D.R. events that lead to a CH
radical in the A-level and consequent photon emission is at least 10%.
Additionally, quenching of the excited CH radicals by electron impact
de-excitation was included in the modeling. This quenching is shown to be
significant: depending on the electron density, it reduces the effective CH
emission by a factor of 1.4 at n_e=1.3*10^20 m^-3, to 2.8 at n_e=9.3*10^20
m^-3. Its inclusion significantly improved agreement between experiment and
modeling
Tritium retention in W plasma-facing materials : Impact of the material structure and helium irradiation
This article has an erratum: DOI 10.1016/j.nme.2020.100729Plasma-facing materials for next generation fusion devices, like ITER and DEMO, will be submitted to intense fluxes of light elements, notably He and H isotopes (HI). Our study focuses on tritium (T) retention on a wide range of W samples: first, different types of W materials were investigated to distinguish the impact of the pristine original structure on the retention, from W-coated samples to ITER-grade pure W samples submitted to various annealing and manufacturing procedures, along with monocrystalline W for reference. Then, He and He-D irradiated W samples were studied to investigate the impact on He-damages such as nano-bubbles (exposures in LHD or PSI-2) on T retention. We exposed all the samples to tritium gas-loading using a gentle technique preventing any introduction of new damage in the material. Tritium desorption is measured by Liquid Scintillation counting (LSC) at ambient and high temperatures (800 degrees C). The remaining T inventory is then measured by sample full dissolution and LSC. Results on T inventory on He exposed samples highlighted that in all cases, tritium desorption as a gas (HT) increases significantly due to the formation of He damages. Up to 1.8 times more T can be trapped in the material through a competition of various mechanisms, but the major part of the inventory desorbs at room temperature, and so will most likely not take part to the long-term trapped inventory for safety and operational perspectives. Unfortunately, investigation of "as received" industrial W (used for the making of plasma-facing materials) highlighted a strong impact of the pre existing defects on T retention: up to 2.5 times more T is trapped in "as received W" compared to annealed and polish W, and desorbs only at 800 degrees C, meaning ideal W material studies may underestimate T inventory for tokamak relevant conditions.Peer reviewe
Recommended from our members
Instrument response during overpower transients at TREAT
A program to empirically analyze data residuals or noise to determine instrument response that occurs during in-pile transient tests is out-lined. As an example, thermocouple response in the Mark III loop during a severe overpower transient in TREAT is studied both in frequency space and in real-time. Time intervals studied included both constant power and burst portions of the power transient. Thermocouple time constants were computed. Benefits and limitations of the method are discussed
- …