Development of a Detector Control System for the ATLAS Pixel Detector

The innermost part of the ATLAS experiment will be a pixel detector containing around 1750 individual detector modules. A detector control system (DCS) is required to handle thousands of I/O channels with varying characteristics. The main building blocks of the pixel DCS are the cooling system, the power supplies and the thermal interlock system, responsible for the ultimate safety of the pixel sensors. The ATLAS Embedded Local Monitor Board (ELMB), a multi purpose front end I/O system with a CAN interface, is foreseen for several monitoring and control tasks. The Supervisory, Control And Data Acquisition (SCADA) system will use PVSS, a commercial software product chosen for the CERN LHC experiments. We report on the status of the different building blocks of the ATLAS pixel DCS.Comment: 3 pages, 2 figures, ICALEPCS 200

The Embedded Local Monitor Board (ELMB) in the LHC Front-end I/O Control System

The Embedded Local Monitor Board is a plug-on board to be used in LHC detectors for a range of different front-end control and monitoring tasks. It is based on the CAN serial bus system and is radiation tolerant and can be used in magnetic fields. The main features of the ELMB are described and results of several radiation tests are presented. I

Solitary magnetic perturbations at the ELM onset

Edge localised modes (ELMs) allow maintaining sufficient purity of tokamak H-mode plasmas and thus enable stationary H-mode. On the other hand in a future device ELMs may cause divertor power flux densities far in excess of tolerable material limits. The size of the energy loss per ELM is determined by saturation effects in the non-linear phase of the ELM, which at present is hardly understood. Solitary magnetic perturbations (SMPs) are identified as dominant features in the radial magnetic fluctuations below 100kHz. They are typically observed close (+-0.1ms) to the onset of pedestal erosion. SMPs are field aligned structures rotating in the electron diamagnetic drift direction with perpendicular velocities of about 10km/s. A comparison of perpendicular velocities suggests that the perturbation evoking SMPs is located at or inside the separatrix. Analysis of very pronounced examples showed that the number of peaks per toroidal turn is 1 or 2, which is clearly lower than corresponding numbers in linear stability calculations. In combination with strong peaking of the magnetic signals this results in a solitary appearance resembling modes like palm tree modes, edge snakes or outer modes. This behavior has been quantified as solitariness and correlated to main plasma parameters. SMPs may be considered as a signature of the non-linear ELM-phase originating at the separatrix or further inside. Thus they provide a handle to investigate the transition from linear to non-linear ELM phase. By comparison with data from gas puff imaging processes in the non-linear phase at or inside the separatrix and in the scrape-off-layer (SOL) can be correlated. A connection between the passing of an SMP and the onset of radial filament propagation has been found. Eventually the findings related to SMPs may contribute to a future quantitative understanding of the non-linear ELM evolution.Comment: submitted to Nuclear Fusio

The detector control system of the ATLAS experiment

The ATLAS experiment is one of the experiments at the Large Hadron Collider, constructed to study elementary particle interactions in collisions of high-energy proton beams. The individual detector components as well as the common experimental infrastructure are supervised by the Detector Control System (DCS). The DCS enables equipment supervision using operator commands, reads, processes and archives the operational parameters of the detector, allows for error recognition and handling, manages the communication with external control systems, and provides a synchronization mechanism with the physics data acquisition system. Given the enormous size and complexity of ATLAS, special emphasis was put on the use of standardized hardware and software components enabling efficient development and long-term maintainability of the DCS over the lifetime of the experiment. Currently, the DCS is being used successfully during the experiment commissioning phase

LHC Communication Infrastructure: Recommendations from the working group

The LHC Working Group for Communication Infrastructure (CIWG) was established in May 1999 with members from the accelerator sector, the LHC physics experiments, the general communication services, the technical services and other LHC working groups. It has spent a year collecting user requirements and at the same time explored and evaluated possible solutions appropriate to the LHC. A number of technical recommendations were agreed, and areas where more work is required were identified. The working group also put forward proposals for organizational changes needed to allow the design project to continue and to prepare for the installation and commissioning phase of the LHC communication infrastructure. This paper reports on the work done and explains the motivation behind the recommendations

Experimental evidence of magnetic flux pumping in ASDEX upgrade

In high-β scenarios with on-axis co-current electron cyclotron current drive, which normally lowers q 0 below unity, the absence of sawteeth suggests the involvement of an additional current redistribution mechanism beyond neoclassical current diffusion. This is supported by imaging motional Stark effect diagnostic measurements, which indicate that q 0 remains consistently around 1. This phenomenon is observed in the presence of a 1/1 mode, indicating its potential role in the current redistribution. It is shown that the mode’s ability to modify the central current and suppress sawteeth increases with plasma pressure. These findings align with a recent theoretical model, which predicts a pressure threshold for sawtooth avoidance by a 1/1 quasi-interchange mode and where this threshold increases with the strength of inward current diffusion. Moreover, the advantages of the flux pumping scenario for future machines are highlighted.</p