Mass Spectrometry of Polymer Electrolyte Membrane Fuel Cells

The chemical analysis of processes inside fuel cells under operating conditions in either direct or inverted (electrolysis) mode and their correlation with potentiostatic measurements is a crucial part of understanding fuel cell electrochemistry. We present a relatively simple yet powerful experimental setup for online monitoring of the fuel cell exhaust (of either cathode or anode side) downstream by mass spectrometry. The influence of a variety of parameters (composition of the catalyst, fuel type or its concentration, cell temperature, level of humidification, mass flow rate, power load, cell potential, etc.) on the fuel cell operation can be easily investigated separately or in a combined fashion. We demonstrate the application of this technique on a few examples of low-temperature (70°C herein) polymer electrolyte membrane fuel cells (both alcohol- and hydrogen-fed) subjected to a wide range of conditions

Redox-mediated C–C bond scission in alcohols adsorbed on CeO2−x thin films

AbstractThe decomposition mechanisms of ethanol and ethylene glycol on well-ordered stoichiometric CeO2(111) and partially reduced CeO2−x (111) films were investigated by means of synchrotron radiation photoelectron spectroscopy, resonant photoemission spectroscopy, and temperature programmed desorption. Both alcohols partially deprotonate upon adsorption at 150 K and subsequent annealing yielding stable ethoxy and ethylenedioxy species. The C–C bond scission in both ethoxy and ethylenedioxy species on stoichiometric CeO2(111) involves formation of acetaldehyde-like intermediates and yields CO and CO2 accompanied by desorption of acetaldehyde, H2O, and H2. This decomposition pathway leads to the formation of oxygen vacancies. In the presence of oxygen vacancies, C–O bond scission in ethoxy species yields C2H4. In contrast, C–C bond scission in ethylenedioxy species on the partially reduced CeO2−x (111) is favored with respect to C–O bond scission and yields methanol, formaldehyde, and CO accompanied by the desorption of H2O and H2. Still, scission of C–O bonds on both sides of the ethylenedioxy species yields minor amounts of accompanying C2H4 and C2H2. C–O bond scission is coupled with a partial recovery of the lattice oxygen in competition with its removal in the form of water

Hydrogen activation on Pt–Sn nanoalloys supported on mixed Sn–Ce oxide films

We have studied the interaction of H2 with Pt–Sn nanoalloys supported on Sn–Ce mixed oxide films of different composition by means of synchrotron radiation photoelectron spectroscopy and resonant photoemission spectroscopy. The model catalysts are prepared in a three step procedure that involves (i) the preparation of well-ordered CeO2(111) films on Cu(111) followed by subsequent physical vapor deposition of (ii) metallic Sn and (iii) metallic Pt. The formation of mixed Sn–Ce oxide is accompanied by partial reduction of Ce4+ cations to Ce3+. Pt deposition leads to the formation of Pt–Sn nanoalloys accompanied by the partial re-oxidation of Ce3+ to Ce4+. Subsequent annealing promotes further Pt–Sn alloy formation at expense of the Sn content in the Sn–Ce mixed oxide. Adsorption of H2 on Pt–Sn/Sn–Ce–O at 150 K followed by stepwise annealing results in reversible reduction of Ce cations caused by spillover of dissociated hydrogen between 150 and 300 K. Above 500 K, annealing of Pt–Sn/Sn–Ce–O in a hydrogen atmosphere results in irreversible reduction of Ce cations. This reduction is caused by the reaction of hydrogen with oxygen provided by the mixed oxide substrate via the reverse spillover to Pt–Sn nanoalloy. The extent of the hydrogen and oxygen spillover strongly depends on the amount of Sn in the Sn–Ce mixed-oxide. We observe an enhancement of hydrogen spillover on Pt–Sn/Sn–Ce–O at low Sn concentration as compared to Sn-free Pt/CeO2. Although the extent of hydrogen spillover on Pt–Sn/Sn–Ce–O with high Sn concentration is comparable to Pt/CeO2, the reverse oxygen spillover is substantially suppressed on these samples

Selective electrooxidation of 2-propanol on Pt nanoparticles supported on Co3O4: an in-situ study on atomically defined model systems

2-Propanol and its dehydrogenated counterpart acetone can be used as a rechargeable electrofuel. The concept involves selective oxidation of 2-propanol to acetone in a fuel cell coupled with reverse catalytic hydrogenation of acetone to 2-propanol in a closed cycle. We studied electrocatalytic oxidation of 2-propanol on complex model Pt/Co3O4(111) electrocatalysts prepared in ultra-high vacuum and characterized by scanning tunneling microscopy. The electrocatalytic behavior of the model electrocatalysts has been investigated in alkaline media (pH 10, phosphate buffer) by means of electrochemical infrared reflection absorption spectroscopy and ex-situ emersion synchrotron radiation photoelectron spectroscopy as a function of Pt particle size and compared with the electrocatalytic behavior of Pt(111) and pristine Co3O4(111) electrodes under similar conditions. We found that the Co3O4(111) film is inactive towards electrochemical oxidation of 2-propanol under the electrochemical conditions (0.3–1.1 VRHE). The electrochemical oxidation of 2-propanol readily occurs on Pt(111) yielding acetone at an onset potential of 0.4 VRHE. The reaction pathway does not involve CO but yields strongly adsorbed acetone species leading to a partial poisoning of the surface sites. On model Pt/Co3O4(111) electrocatalysts, we observed distinct metal support interactions and particle size effects associated with the charge transfer at the metal/oxide interface. We found that ultra-small Pt particles (around 1 nm and below) consist of partially oxidized Pt δ + species which show minor activity towards 2-propanol oxidation. In contrast, conventional Pt particles (particle size of a few nm) are mainly metallic and show high activity toward 2-propanol oxidation

Mass Spectrometry of Polymer Electrolyte Membrane Fuel Cells

The chemical analysis of processes inside fuel cells under operating conditions in either direct or inverted (electrolysis) mode and their correlation with potentiostatic measurements is a crucial part of understanding fuel cell electrochemistry. We present a relatively simple yet powerful experimental setup for online monitoring of the fuel cell exhaust (of either cathode or anode side) downstream by mass spectrometry. The influence of a variety of parameters (composition of the catalyst, fuel type or its concentration, cell temperature, level of humidification, mass flow rate, power load, cell potential, etc.) on the fuel cell operation can be easily investigated separately or in a combined fashion. We demonstrate the application of this technique on a few examples of low-temperature (70°C herein) polymer electrolyte membrane fuel cells (both alcohol- and hydrogen-fed) subjected to a wide range of conditions