318 research outputs found
Recommended from our members
Stability of optical elements in the NIF target area building
The Target Area Building (TAB) of the National Ignition Facility (NIF) is 300 feet long, 100 feet wide, and 100 feet tall and is comprised of a cylindrical target building and two switchyard space frames. The reinforced concrete target building houses the target chamber, target positioner, turning mirrors, final optics assemblies, and diagnostics, while the steel switchyard space frames support turning mirrors and diagnostic equipment. Within the TAB, the 192 independent laser beams of the NIF laser system are required to be accurately positioned. In order to satisfy the engineering system requirement for optical system positioning (stability on target), the TAB must provide a stable platform for optical elements before and during a shot. This paper summarizes the stability analyses that were performed in support of the TAB and optical system design. Sources that influence optic stability are structural excitations, such as ambient and wind induced vibrations, and thermal transients, such as diurnal and HVAC temperature changes. A positioning error budget has been developed for the NIF project for use in the design and evaluation of structures which support optical elements. To satisfy the error budget requirements, vibrational stability will be achieved through a combination of facility design, optic support structure design, and passive damping. Thermal stability will be accomplished by using high thermal-mass concrete structures, conditioned air flow, and a reduction of heat sources. Finite element analysis has been used to evaluate the design of the TAB and optical support structures. A detailed structural model of the TAB that includes the target positioner, target chamber, turning mirrors, and diagnostics, has been used for stability evaluations. Finite element analyses covering ambient ground vibration, thermal loads, pressure fluctuations, and wind excitations have demonstrated that the current design of the TAB provides a stable platform for maintaining beam alignment
Polyethylene imine-based receptor immobilization for label free bioassays
Polyethylene imine (PEI) based immobilization of antibodies is described and the concept is proved on the
label free assay of C-Reactive Protein (CRP). This novel immobilization method is composed of a hyperbranched
PEI layer which was deposited at a high pH (9.5) on the sensor surface. The free amino groups
of PEI were derivatized with neutravidin by Biotin N-hydroxysuccinimide ester and the biotinylated
anti-CRP antibody immobilized on this layer. Direct binding assay of recombinant CRP was successfully
performed in the low μg/ml concentrations using a label free optical waveguide biosensor
Nan-O-Style – experiments and arts
In this project, high school students (aged 16-17) tested various protocols of experiments in nanotechnology and evaluated them whether such experiments could also be performed by middle school students (aged 11-15) or even elementary school students (aged 6-10). Protocols pre-selected and provided by the instructing team consisting of Sciencetainment and the Department of Biosciences, University of Salzburg were applied. Laboratory techniques such as thin-layer chromatography, measuring the contact angle by high-resolution 3D microscopy and analyzing and constructing surface layers represented some of the experiments performed. Moreover, students produced short video clips and images and designed photo-collages out of microscopic and electron microscopic pictures. Hence, the school students acquired a number of soft skills during this special science day
Mental health care for irregular migrants in Europe: Barriers and how they are overcome
This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use,
distribution, and reproduction in any medium, provided the original work is properly cited
Virgo calibration and reconstruction of the gravitational wave strain during VSR1
Virgo is a kilometer-length interferometer for gravitational waves detection
located near Pisa. Its first science run, VSR1, occured from May to October
2007. The aims of the calibration are to measure the detector sensitivity and
to reconstruct the time series of the gravitational wave strain h(t). The
absolute length calibration is based on an original non-linear reconstruction
of the differential arm length variations in free swinging Michelson
configurations. It uses the laser wavelength as length standard. This method is
used to calibrate the frequency dependent response of the Virgo mirror
actuators and derive the detector in-loop response and sensitivity within ~5%.
The principle of the strain reconstruction is highlighted and the h(t)
systematic errors are estimated. A photon calibrator is used to check the sign
of h(t). The reconstructed h(t) during VSR1 is valid from 10 Hz up to 10 kHz
with systematic errors estimated to 6% in amplitude. The phase error is
estimated to be 70 mrad below 1.9 kHz and 6 micro-seconds above.Comment: 8 pages, 8 figures, proceedings of Amaldi 8 conference, to be
published in Journal of Physics Conference Series (JPCS). Second release:
correct typo
Sensitivity to Gravitational Waves from Compact Binary Coalescences Achieved during LIGO's Fifth and Virgo's First Science Run
We summarize the sensitivity achieved by the LIGO and Virgo gravitational
wave detectors for compact binary coalescence (CBC) searches during LIGO's
fifth science run and Virgo's first science run. We present noise spectral
density curves for each of the four detectors that operated during these
science runs which are representative of the typical performance achieved by
the detectors for CBC searches. These spectra are intended for release to the
public as a summary of detector performance for CBC searches during these
science runs.Comment: 12 pages, 5 figure
Directional limits on persistent gravitational waves using LIGO S5 science data
The gravitational-wave (GW) sky may include nearby pointlike sources as well
as astrophysical and cosmological stochastic backgrounds. Since the relative
strength and angular distribution of the many possible sources of GWs are not
well constrained, searches for GW signals must be performed in a
model-independent way. To that end we perform two directional searches for
persistent GWs using data from the LIGO S5 science run: one optimized for
pointlike sources and one for arbitrary extended sources. The latter result is
the first of its kind. Finding no evidence to support the detection of GWs, we
present 90% confidence level (CL) upper-limit maps of GW strain power with
typical values between 2-20x10^-50 strain^2 Hz^-1 and 5-35x10^-49 strain^2
Hz^-1 sr^-1 for pointlike and extended sources respectively. The limits on
pointlike sources constitute a factor of 30 improvement over the previous best
limits. We also set 90% CL limits on the narrow-band root-mean-square GW strain
from interesting targets including Sco X-1, SN1987A and the Galactic Center as
low as ~7x10^-25 in the most sensitive frequency range near 160 Hz. These
limits are the most constraining to date and constitute a factor of 5
improvement over the previous best limits.Comment: 10 pages, 4 figure
Migrant health in Italy: a better health status difficult to maintain-country of origin and assimilation effects studied from the Italian risk factor surveillance data
Many studies on migrant health have focused on aspects of morbidity and mortality, but very few approach the relevant issues of migrants' health considering behavioral risk factors. Previous studies have often been limited methodologically because of sample size or lack of information on migrant country of origin. Information about risk factors is fundamental to direct any intervention, particularly with regard to non-communicable diseases that are leading causes of death and disease. Thus, the main focus of our analysis is the influence of country of origin and the assimilation process
- …