37,795 research outputs found
Distributed lag models for hydrological data
The distributed lag model (DLM), used most prominently in air pollution studies, finds application
wherever the effect of a covariate is delayed and distributed through time. We explore the use of modified formulations
of DLMs to provide flexible varying-coeficient models with smoothness constraints, applicable in any setting in which
lagged covariates are regressed on a time-dependent response. The models are applied to simulated flow and rainfall
data and to flow data from a Scottish mountain river, with particular emphasis on approximating the relationship
between environmental covariates and flow regimes in order to detect the influence of unobserved processes. It was
found that under certain rainfall conditions some of the variability in the influence of rainfall on flow arises through
a complex interaction between antecedent ground wetness and the time-delay in rainfall. The models are able to
identify subtle changes in rainfall response, particularly in the location of peak influence in the lag structure and offer
a computationally attractive approach for fitting DLMs
Minimizing boundary layer bleed for a mixed compression inlet
An experimental investigation of a full scale mixed compression inlet sized for the TF30-P-3 turbofan engine was conducted at Mach 2.5 and 2.0 operating conditions. The two cone axisymmetric inlet had minimum internal contraction consistent with high total pressure recovery and low cowl drag. At Mach 2.5, inlet recovery exceeded 0.90 with only 0.02 centerbody bleed mass-flow ratio and zero cowl bleed. A centerbody bleed of approximately 0.05 gave a maximum inlet unstart angle-of-attack of 6.85 deg. Inlet performance and angle-of-attack tolerance is presented for operation at Mach 2.5 and 2.0
Performance of vortex generators in a Mach 2.5 low-bleed full scale 45-percent-internal-contraction axisymmetric inlet
Steady-state and dynamic flow characteristics associated with two sets of vortex generators having different mixing criteria were determined. The inlet performance with and without these vortex generators is presented. The vortex generators were successful in eliminating separation, increasing area-weighted total pressure recovery, and decreasing distortion. Transmission times obtained from cross-correlations of the wall static pressures and the diffuser exit total pressure showed no effect of the upstream flow characteristics on the diffuser exit pressures when generators were used. Without generators, separation occurred and the upstream pressure characteristics had immediate effects on the diffuser exit pressure characteristics
Distortion in a full-scale bicone inlet with internal focused compression and 45 percent internal contraction
The distortion characteristics were investigated at the subsonic diffuser exit of a full-scale, Mach 2.5, axisymmetric, mixed compression inlet. Performance and steady-state distortion characteristics were obtained at zero and maximum angle of attack and during an inlet unstart-restart sequence. For the configuration with no cowl bleed, steady-state distortion P(max)P(min)P(bar) ranged from 0.10 for critical inlet operation at 0 deg angle-of-attack to 0.306 for supercritical inlet operation at 6.84 deg angle-of-attack. Vortex generators provided a 50 percent reduction in steady-state distortion for critical operation. Bleed has a smaller effect on steady-stated distortion
Boundary layer bleed system study for a full-scale, mixed-compression inlet with 45 percent internal contraction
The results of an experimental bleed development study for a full-scale, Mach 2.5, axisymmetric, mixed-compression inlet were presented. The inlet was designed to satisfy the airflow requirements of the TF30-P-3 turbofan engine. Capabilities for porous bleed on the cowl surface and ram-scoop/flush-slot bleed on the centerbody were provided. A configuration with no bleed on the cowl achieved a minimum stable, diffuser exit, total pressure recovery of 0.894 with a centerbody-bleed mass flow ratio of 0.02. Configurations with cowl bleed had minimum stable recoveries as high as 0.900 but suffered range decrement penalties from the increased bleed mass flow removal. Limited inlet stability and unstart angle-of-attack data are presented
Performance and surge limits of a TF30-P-3 turbofan engine/axisymmetric mixed-compression inlet propulsion system at Mach 2.5
Steady-state performance and inlet-engine compatibility were investigated with a low-bleed inlet. The inlet had minimum internal contraction, consistent with high total pressure recovery and low cowl drag. The inlet-engine combination displayed good performance with only about 2% of inlet performance bleed. The inlet-engine combination had 5.58 deg angle-of-attack capability with 6% bleed
A spectrum of ozone from 760 to 5800 cm-1
An atlas of O3 lines between 760 and 5800/cm obtained from a low pressure, long-path-length sample of O3 at 296K is presented. Many of the line centers are marked and their positions tabulated
- …