A Foundation Wall Heat Exchanger Model and Validation Study

Making use of foundation substructural elements as ground heat exchangers is an attractive option for larger non-residential buildings. An alternative to Energy Piles is to use wall substructures – so called diaphragm or screen walls – with embedded pipes that are partly below ground and partly exposed to basement spaces. This paper will describe the development of a model of such a heat exchanger that uses a weighting factor approach known as Dynamic Thermal Networks (DTN). This approach allows for detailed representation of the wall section geometry and multiple boundary conditions. In this case thermal boundary conditions are applied at surfaces representing the adjacent ground and the semiexposed basement wall surface in addition to the pipe surface. The weighting factors for the model have been derived using a parametric numerical model that has been developed using the OpenFOAM library. Validation of the model has been carried out using data from an extended series of thermal response test (TRT) measurements at a full-scale diaphragm wall heat exchanger in Barcelona. In this paper, development of the model using the DTN approach will be briefly described along with the parametric numerical modelling approach used to derive the weighting factor data. Validation test procedures will be presented along with comparisons between the predicted and measured fluid temperatures and heat transfer rates. Given some uncertainty in the experimental thermal properties, the model was able to predict the dynamics of thermal response over a range of operating conditions with reasonable accuracy and using very modest computational resources

A Model of a Diaphragm Wall Ground Heat Exchanger

Ground thermal energy is a sustainable source that can substantially reduce our dependency on conventional fuels for heating and cooling of buildings. To exploit this source, foundation sub-structures with embedded heat exchanger pipes are employed. Diaphragm wall heat exchangers are one such form of ground heat exchangers, where part of the wall is exposed to the basement area of the building on one side, while the other side and the further depth of the wall face the surrounding ground. To assess the thermal performance of diaphragm wall heat exchangers, a model that takes the wall geometry and boundary conditions at the pipe, basement, and ground surfaces into account is required. This paper describes the development of such a model using a weighting factor approach, known as Dynamic Thermal Networks (DTN), that allows representation of the three-dimensional geometry, required boundary conditions, and heterogeneous material properties. The model is validated using data from an extended series of thermal response test measurements at two full-scale diaphragm wall heat exchanger installations in Barcelona, Spain. Validation studies are presented in terms of comparisons between the predicted and measured fluid temperatures and heat transfer rates. The model was found to predict the dynamics of thermal response over a range of operating conditions with good accuracy and using very modest computational resources

Effect of vitamin C and vitamin E on lung contusion: A randomized clinical trial study

ABSTRACT There is association between lung contusion (lC) and a progressive in fl ammatory response. The protective effect of vitamin C and vitamin E, as strong free radical scavengers on favourite outcome of (LC) in animal models,has been confirmed. Design: to evaluate the effect of vitamins, E and C on arterial blood gas (ABG) and ICU stay, in (LC), with injury severity score (ISS) 18 ± 2, due to blunt chest trauma. Methods: This study was a randomized, double-blind, placebo controlled clinical trial. Patients with (ISS)18 ± 2 blunt chest trauma, who meet criteria, participated in the study. A total of 80 patients from Feb 2015 to Jun2018and were randomly divided into 4 groups. Patients received intravenous vitamin E (1000IU mg), was (group I);intravenous vitamin C (500) (group II). Vitamin C + vitamin E = (group III), and intravenous distilled water = (control group) or (group IV). ABG, serum cortisol, and CRP levels were determined at baseline, 24 h and 48 h after the intervention. Results: a significant decrease in ICU stay in group III compared to other groups (p < 0.001). Co-administration of vitamin C and vitamin E showed significant increases pH (values to reference range from acidemia”), oxygen pressure, and oxygen saturation in group III compared to other groups (p <0.001). A significant decrease in carbon dioxide pressure was also detected after receiving vitamin C and vitamin E in group III, compared to other groups (p < 0.001). There was no significant difference cortisol and CRP levels between groups after the intervention. Conclusion: Co-administration of vitamin C and vitamin E, improve the ABG parameters and reduce I

Investigations into Thermal Resistance of Tunnel Lining Heat Exchangers

Geothermal energy is a promising and sustainable source that can reduce current dependence on conventional fuels for thermal energy production. To exploit this source of energy thermo-active geostructures such as tunnel lining heat exchangers are being investigated theoretically as well as experimentally. These geostructures are composed of concrete panels embedded with reinforcement cages fitted with absorber pipes. Several engineering projects in China, Finland and Italy have deployed such heat exchangers in tunnels. To achieve efficient energy production, characterisation of these systems require realistic models of the substructure heat exchanger. Therefore investigations into thermal resistance of the heat exchanger is vital. The present study is concerned with quantifying the thermal resistance of tunnel lining heat exchangers where the thermal boundary surfaces are applied at surfaces representing the adjacent ground and the exposed concrete, in addition to the pipe surface. Steady state temperature distribution in a two dimensional cross section of a tunnel lining heat exchanger is investigated using the boundary collocation least squares method. Design parameters including pipe and tunnel lining specifications are used as model inputs

Comparative structural and mechanical studies on polyamide 6 knitted-reinforced single polymer composites prepared by different reactive processing techniques

Single polymer laminate composites based on anionic polyamide 6 (PA6) matrix-reinforced by PA6 knitted textile structures (KSPC) were produced by nylon reactive injection molding and powder coating/compression molding (PCCM) processing techniques. The effect of the reinforcement’s structure and the fiber volume fraction on the mechanical properties of the knitted-reinforced PA6 composites resulting from the two methods were investigated and compared. The morphology and the crystalline structure of KSPC materials were studied to identify the main factors determining the tensile properties. The results showed that the PCCM method produced laminate composites with higher Young’s modulus and mechanical strength in tension. Microscopy, differential scanning calorimetry and X-ray diffraction experiments were carried out to correlate the morphology and crystalline structure of the composites and their precursors with the different tensile behavior of KSPC prepared using the two techniques. The microscopy and X-ray scattering studies suggested the formation of a transcrystalline layer at the matrix/reinforcement interface. POLYM. COMPOS., 40:E886–E897, 2019. © 2018 Society of Plastics EngineersThis work was partially financed by FEDER funds through the COMPETE program and by national funds through FCT – Foundation for Science and Technology within the project POCI‐01‐0145‐FEDER‐007136. SDT thanks FCT for his PhD Grant SFRH/BD/94759/2013. NVD thanks for the financial support of FCT in the frames of the strategic project UID/CTM/50025/2013. Finally, ZZD is thankful to FCT for the SFRH/BSAB/130271/2017 personal research grant. All authors gratefully acknowledge the support of the project TSSiPRO‐NORTE‐01‐0145‐FEDER‐000015 funded by the regional operational program NORTE 2020, under the PORTUGAL 2020 Partnership Agreement, through the European Regional Development Fund

Mechano-morphological studies of polyamide 6 based single polymer laminate composites prepared by different reactive processing techniques

Single polymer laminate composites based on polyamide 6 (PA6) were prepared by two methods: (i) reactive injection molding and (ii) powder coating/compression molding, both carried out in the presence of PA6 woven textile plies. The effect of the textile volume fraction Vf on the tensile properties of all composites was investigated. The laminates obtained by powder coating/compression molding displayed best mechanical performance, whereby in the composites with Vf = 15%, the improvement of the elastic modulus reached 98% in respect to commercial hydrolytic PA6 reference, or 50–86% as compared to neat anionic PA6 samples. Polarizing light microscopy with image processing was used for morphological characterization. A transcrystalline layer at the fiber-matrix interface was detected in all laminates with thicknesses between 0.5 and 3.0 μm, depending on the preparation technique applied. The thermal stability was studied in the temperature range of 30°C-550 °C. The laminates obtained by reactive injection molding displayed the lowest initial decomposition temperature due to the presence of oligomers. Selected laminate composites were reprocessed by grinding and injection molding. The recycled composites obtained by powder coating displayed a 38% increase of the elastic modulus in respect to commercial hydrolytic PA6 thus confirming the sustainability and recyclability of PA6-based single polymer composites.This work was partially financed by FEDER funds through the COMPETE program and by national funds through FCT – Foundation for Science and Technology within the project .POCI-01-0145-FEDER 007136 SDT thanks FCT for his PhD Grant SFRH/BD/94759/2013. ZZD and NVD thank the National Funds through FCT-Portuguese Foundation for Science and Technology, project reference UID/CTM/50025/2019. All authors gratefully acknowledge the support of the project TSSiPRO NORTE-01-0145-FEDER-000015 funded by the regional operational program NORTE 2020, under the PORTUGAL 2020 Partnership Agreement, through the European Regional Development Fund

Activity map of the tammar X chromosome shows that marsupial X inactivation is incomplete and escape is stochastic

BACKGROUND: X chromosome inactivation is a spectacular example of epigenetic silencing. In order to deduce how this complex system evolved, we examined X inactivation in a model marsupial, the tammar wallaby (Macropus eugenii). In marsupials, X inactivation is known to be paternal, incomplete and tissue-specific, and occurs in the absence of an XIST orthologue. RESULTS: We examined expression of X-borne genes using quantitative PCR, revealing a range of dosage compensation for different loci. To assess the frequency of 1X- or 2X-active fibroblasts, we investigated expression of 32 X-borne genes at the cellular level using RNA-FISH. In female fibroblasts, two-color RNA-FISH showed that genes were coordinately expressed from the same X (active X) in nuclei in which both loci were inactivated. However, loci on the other X escape inactivation independently, with each locus showing a characteristic frequency of 1X-active and 2X-active nuclei, equivalent to stochastic escape. We constructed an activity map of the tammar wallaby inactive X chromosome, which identified no relationship between gene location and extent of inactivation, nor any correlation with the presence or absence of a Y-borne paralog. CONCLUSIONS: In the tammar wallaby, one X (presumed to be maternal) is expressed in all cells, but genes on the other (paternal) X escape inactivation independently and at characteristic frequencies. The paternal and incomplete X chromosome inactivation in marsupials, with stochastic escape, appears to be quite distinct from the X chromosome inactivation process in eutherians. We find no evidence for a polar spread of inactivation from an X inactivation center.This project was funded by grants to JAMG and PDW from the Australian Research Council

Activity map of the tammar X chromosome shows that marsupial X inactivation is incomplete and escape is stochastic

BACKGROUND: X chromosome inactivation is a spectacular example of epigenetic silencing. In order to deduce how this complex system evolved, we examined X inactivation in a model marsupial, the tammar wallaby (Macropus eugenii). In marsupials, X inactivation is known to be paternal, incomplete and tissue-specific, and occurs in the absence of an XIST orthologue. RESULTS: We examined expression of X-borne genes using quantitative PCR, revealing a range of dosage compensation for different loci. To assess the frequency of 1X- or 2X-active fibroblasts, we investigated expression of 32 X-borne genes at the cellular level using RNA-FISH. In female fibroblasts, two-color RNA-FISH showed that genes were coordinately expressed from the same X (active X) in nuclei in which both loci were inactivated. However, loci on the other X escape inactivation independently, with each locus showing a characteristic frequency of 1X-active and 2X-active nuclei, equivalent to stochastic escape. We constructed an activity map of the tammar wallaby inactive X chromosome, which identified no relationship between gene location and extent of inactivation, nor any correlation with the presence or absence of a Y-borne paralog. CONCLUSIONS: In the tammar wallaby, one X (presumed to be maternal) is expressed in all cells, but genes on the other (paternal) X escape inactivation independently and at characteristic frequencies. The paternal and incomplete X chromosome inactivation in marsupials, with stochastic escape, appears to be quite distinct from the X chromosome inactivation process in eutherians. We find no evidence for a polar spread of inactivation from an X inactivation center.This project was funded by grants to JAMG and PDW from the Australian Research Council

Functional interleukin-17 receptor A is expressed in central nervous system glia and upregulated in experimental autoimmune encephalomyelitis

<p>Abstract</p> <p>Background</p> <p>Interleukin-17A (IL-17A) is the founding member of a novel family of inflammatory cytokines that plays a critical role in the pathogenesis of many autoimmune diseases, including multiple sclerosis (MS) and its animal model, experimental autoimmune encephalomyelitis (EAE). IL-17A signals through its receptor, IL-17RA, which is expressed in many peripheral tissues; however, expression of IL-17RA in the central nervous system (CNS) and its role in CNS inflammation are not well understood.</p> <p>Methods</p> <p>EAE was induced in C57Bl/6 mice by immunization with myelin oligodendroglial glycoprotein. IL-17RA expression in the CNS was compared between control and EAE mice using RT-PCR, in situ hybridization, and immunohistochemistry. Cell-type specific expression was examined in isolated astrocytic and microglial cell cultures. Cytokine and chemokine production was measured in IL-17A treated cultures to evaluate the functional status of IL-17RA.</p> <p>Results</p> <p>Here we report increased IL-17RA expression in the CNS of mice with EAE, and constitutive expression of functional IL-17RA in mouse CNS tissue. Specifically, astrocytes and microglia express IL-17RA <it>in vitro</it>, and IL-17A treatment induces biological responses in these cells, including significant upregulation of MCP-1, MCP-5, MIP-2 and KC chemokine secretion. Exogenous IL-17A does not significantly alter the expression of IL-17RA in glial cells, suggesting that upregulation of chemokines by glial cells is due to IL-17A signaling through constitutively expressed IL-17RA.</p> <p>Conclusion</p> <p>IL-17RA expression is significantly increased in the CNS of mice with EAE compared to healthy mice, suggesting that IL-17RA signaling in glial cells can play an important role in autoimmune inflammation of the CNS and may be a potential pathway to target for therapeutic interventions.</p