72 research outputs found

    Non-dispersive ultra-violet spectroscopic detection of formaldehyde gas for indoor environments

    Get PDF
    We describe a simple method for detecting formaldehyde using low resolution non-dispersive UV absorption spectroscopy. A two channel sensor was developed, making use of a strong absorption peak at 339 nm and a neighbouring region of negligible absorption at 336 nm as a reference. Using a modulated UV LED as a light source and narrow laser-line filters to select the desired spectral bands, a simple detection system was constructed specifically targeted at formaldehyde. By paying particular attention to sources of noise, a minimum detectable absorbance of 5×10 -5 AU was demonstrated with a 20 s averaging period (as ΔI/I0). The system was tested with formaldehyde finding a limit of detection of 4.3 ppm for a 195 mm gas cell. As a consequence of the low gas flow rates used in our test system, a time period of over 8 min was used in further tests, which increased the minimum detectable absorbance to 2×10 -4 AU, 17 ppm of formaldehyde. The increase was the result of thermal drift caused by unwanted temperature variation of the UV LED and the filters, resulting in a zero uncertainty estimated at 560 ppm °C -1 and 100ppm °C -1 respectively

    Aerosol-assisted CVD synthesis, characterisation and gas-sensing application of gold-functionalised tungsten oxide

    Get PDF
    Tungsten oxide nanoneedles (NNs) functionalised with gold nanoparticles (NPs) have been integrated with alumina gas-sensor platforms using a simple and effective co-deposition method via aerosol-assisted chemical vapour deposition (AACVD) utilising a novel gold precursor, (NH4)AuCl4. The gas-sensing results show that gold NP functionalisation of tungsten oxide NNs improves the sensitivity of response to ethanol, with sensitivity increasing and response time decreasing with increasing amount of gold

    Development of Wind Alarm Systems for Road and Rail Vehicles: Presentation of the WEATHER project

    Get PDF
    The development of a new concept of wind alarm systems for road and rail transportation is presented. The alarm is funded on a risk assessment approach, taking into account wind modelling and prediction, aerodynamic forces, vehicle dynamics

    The use of electrochemical sensors for monitoring urban air quality in low-cost, high-density networks

    Get PDF
    Measurements at appropriate spatial and temporal scales are essential for understanding and monitoring spatially heterogeneous environments with complex and highly variable emission sources, such as in urban areas. However, the costs and complexity of conventional air quality measurement methods means that measurement networks are generally extremely sparse. In this paper we show that miniature, low-cost electrochemical gas sensors, traditionally used for sensing at parts-per-million (ppm) mixing ratios can, when suitably configured and operated, be used for parts-per-billion (ppb) level studies for gases relevant to urban air quality. Sensor nodes, in this case consisting of multiple individual electrochemical sensors, can be low-cost and highly portable, thus allowing the deployment of scalable high-density air quality sensor networks at fine spatial and temporal scales, and in both static and mobile configurations.This work was supported by EPSRC (grant number EP/E002102/1) and the Department for Transport

    Plant growth and development in relation to the microclimate of a sorghum/groundnut intercrop

    Get PDF
    An intercrop of one row of sorghum (Sorghum bicolor (L.) Moench) and three rows of groundnut (Arachis hypogaea (L.)) and sole crops of the two species were grown with limited water supply on an alfisol in central India. The faster growth rate of intercropped sorghum was the result of a greater fraction of light being intercepted rather than a higher efficiency () of conversion of light into dry matter. In intercropped groundnut, there was a strong correlation between the growth rate of each row and the fraction of light it intercepted, and although shading by the sorghum reduced the latter in comparison with the sole crop, was higher. Two patterns of response were evident in the intercropped groundnut. Those involving resource use (light and water) and dry matter production were lowest in the outer two rows and highest in the centre row, while those involving development (e.g. pod numbers) increased from the least shaded row to the most shaded. Competition for water by the more aggressive sorghum was thought to be responsible for the first response, and temperature and water potential gradients caused by differing degrees of shading for the second. The effect of the interaction of these two responses on the harvest index is discussed

    A Nairobi experiment in using low cost air quality monitors

    Get PDF
    Many African cities have growing air quality problems, but few have air quality monitoring systems in place. Low cost air quality sensors have the potential to bridge this data gap. This study describes the experimental deployment of six low cost air quality monitors consisting of an optical particle counter Alphasense OPC-N2 for measuring PM1, PM2.5 and PM10, and Alphasense A-series electrochemical (amperometric) gas sensors: NO2-A43F, SO2-A4, NO-A4 for measuring NO2, NO and SO2 in four schools, the United Nations Environment Program (UNEP) headquarters and a community center in Nairobi. The monitors were deployed on May 1 2016 and are still logging data. This paper analyses the data from May 1 2016 to Jan 11 2017. By examining the data produced by these sensors, we illustrate the strengths, as well as the technical limitations of using low cost sensors for monitoring air quality. We show that despite technical limitations, sensors can provide indicative measurements of air quality that are valuable to local communities. It was also found that such a sensor network can play an important role in engaging citizens by raising awareness about the importance of addressing poor air quality. We conclude that these sensors are clearly a potentially important complement but not a substitute for high quality and reliable air quality monitoring systems as problems of calibration, certification, quality control and reporting remain to be solve

    Review of low-cost sensors for indoor air quality: Features and applications

    Get PDF
    Humans spend the majority of their time indoors, where they are potentially exposed to hazardous pollutants. Within this context, over the past few years, there has been an upsurge of low-cost sensors (LCS) for the measurement of indoor air pollutants, motivated both by recent technological advances and by increased awareness of indoor air quality (IAQ) and its potential negative health impacts. Although not meeting the performance requirements for reference regulatory-equivalent monitoring indoors, LCS can provide informative measurements, offering an opportunity for high-resolution monitoring, emission source identification, exposure mitigation and managing IAQ and energy efficiency, among others. This article discusses the strengths and limitations that LCS offer for applications in the field of IAQ monitoring; it provides an overview of existing sensor technologies and gives recommendations for different indoor applications, considering their performance in the complex indoor environment and discussing future trends
    corecore