A modified AHP algorithm for network selection

This paper addresses the concept of ranking networks to the multiple criteria of customers to find the best and alternative networks. The use of modified AHP algorithm has been shown to provide better network ranking for reasonable customer objectives than the traditional AHP method. Both the traditional method and the proposed method produced results subjective to the customer requirements. However, the proposed method is more intuitive to the customers through direct capture of their exact requirements rather than an interpretation of their requirements through pair-wise comparison alone. Also, the proposed method is less time-consuming and results are of higher quality

Free singularity path planning of hybrid parallel robot

This paper presents a singularity-free path planning approach for a hybrid parallel robot. The hybrid robot is composed of two well-known parallel robots, a hexapod and a tripod, that are serially connected. In this paper a methodology is developed to avoid singularity configurations of the hybrid parallel robot. Nominal polynomial paths are used for motion of end effector, and the strokes of each actuator is calculated by using the developed inverse kinematic. A MATLAB program has been developed to generate the designed paths, and several poses have been tested in a CAD model of the hybrid parallel robot to validate the feasibility of the path planning approach

Lower Limb Rehabilitation Using Patient Data

The aim of this study is to investigate the performance of a 6-DoF parallel robot in tracking the movement of the foot trajectory of a paretic leg during a single stride. The foot trajectories of nine patients with a paretic leg including both males and females have been measured and analysed by a Vicon system in a gait laboratory. Based on kinematic and dynamic analysis of a 6-DoF UPS parallel robot, an algorithm was developed in MATLAB to calculate the length of the actuators and their required forces during all trajectories. The workspace and singularity points of the robot were then investigated in nine different cases. A 6-DoF UPS parallel robot prototype with high repeatability was designed and built in order to simulate a single stride. Results showed that the robot was capable of tracking all of the trajectories with the maximum position error of 1.2 mm

Vision-based sensor for three-dimensional vibrational motion detection in biological cell injection

Intracytoplasmic sperm injection (ICSI) is an infertility treatment where a single sperm is immobilised and injected into the egg using a glass injection pipette. Minimising vibration in three orthogonal axes is essential to have precise injector motion and full control during the egg injection procedure. Vibration displacement sensing using physical sensors in ICSI operation is challenging since the sensor interfacing is not practically feasible. This study proposes a non-invasive technique to measure the three-dimensional vibrational motion of the injection pipette by a single microscope camera during egg injection. The contrast-limited adaptive histogram equalization (CHALE) method and blob analyses technique were employed to measure the vibration displacement in axial and lateral axes, while the actual dimension of the focal axis was directly measured using the Brenner gradient algorithm as a focus measurement algorithm. The proposed algorithm operates between the magnifications range of 4× to 40× with a resolution of half a pixel. Experiments using the proposed vision-based algorithm were conducted to measure and verify the vibration displacement in axial and lateral axes at various magnifications. The results were compared against manual procedures and the differences in measurements were up to 2% among all magnifications. Additionally, the effect of injection speed on lateral vibration displacement was measured experimentally and was used to determine the values for egg deformation, force fluctuation, and penetration force. It was shown that increases in injection speed significantly increases the lateral vibration displacement of the injection pipette by as much as 54%. It has been demonstrated successfully that visual sensing has played a key role in identifying the limitation of the egg injection speed created by lateral vibration displacement of the injection pipette tip

Decoding children dental health risks:a machine learning approach to identifying key influencing factors

Introduction and objectives: This study investigates key factors influencing dental caries risk in children aged 7 and under using machine learning techniques. By addressing dental caries’ prevalence, it aims to enhance early identification and preventative strategies for high-risk individuals. Methods: Data from clinical examinations of 356 children were analyzed using Logistic Regression, Decision Trees, and Random Forests models. These models assessed the influence of dietary habits, fluoride exposure, and socio-economic status on caries risk, emphasizing accuracy, precision, recall, F1 score, and AUC metrics. Results: Poor oral hygiene, high sugary diet, and low fluoride exposure were identified as significant caries risk factors. The Random Forest model demonstrated superior performance, illustrating the potential of machine learning in complex health data analysis. Our SHAP analysis identified poor oral hygiene, high sugary diet, and low fluoride exposure as significant caries risk factors. Conclusion: Machine learning effectively identifies and quantifies dental caries risk factors in children. This approach supports targeted interventions and preventive measures, improving pediatric dental health outcomes. Clinical significance: By leveraging machine learning to pinpoint crucial caries risk factors, this research lays the groundwork for data-driven preventive strategies, potentially reducing caries prevalence and promoting better dental health in children