Optimization of Strut Diameters in Lattice Structures

Additive manufactured lattice structures show a high potential for lightweight design. Currently, these structures have a periodical build-up, which leads to disadvantageous stress states. On the one hand, unfavorable bending loads on the single struts appear. This can be avoided by an adaption of the course of the structure to the main stress directions inside the part. On the other hand, different stress values are appearing inside the single struts. Therefore, a procedure for the optimization of the struts diameters is presented. Thus, it becomes possible to achieve equal stresses in the whole structure and gain a better lightweight performance.Mechanical Engineerin

Comparison of dynamic compression behavior of single crystal sapphire to polycrystalline alumina

Due to the considerable interest in the shock loading behavior of aluminum oxide whether it is in the polycrystalline phase or in the single crystal phase well-controlled experiments were conducted to probe differences in shock loading behavior between these two materials. Previous studies concluded that the behavior was similar but careful examination of well-controlled experiments has revealed the two materials are different.Although the experimental results appear to have the same behavior in the shock velocity vs. particle velocity plane, they are considerably different in the stressevolume compression plane and evidence is provided that indicates the single crystal remains crystalline up to the stresses imposed for this analysis. This is an extremely interesting observation since it has many implications including developing dynamic material models capable of transitioning between individual grains and polycrystalline material

Mechanical cell-matrix feedback explains pairwise and collective endothelial cell behavior in vitro

In vitro cultures of endothelial cells are a widely used model system of the collective behavior of endothelial cells during vasculogenesis and angiogenesis. When seeded in an extracellular matrix, endothelial cells can form blood vessel-like structures, including vascular networks and sprouts. Endothelial morphogenesis depends on a large number of chemical and mechanical factors, including the compliancy of the extracellular matrix, the available growth factors, the adhesion of cells to the extracellular matrix, cell-cell signaling, etc. Although various computational models have been proposed to explain the role of each of these biochemical and biomechanical effects, the understanding of the mechanisms underlying in vitro angiogenesis is still incomplete. Most explanations focus on predicting the whole vascular network or sprout from the underlying cell behavior, and do not check if the same model also correctly captures the intermediate scale: the pairwise cell-cell interactions or single cell responses to ECM mechanics. Here we show, using a hybrid cellular Potts and finite element computational model, that a single set of biologically plausible rules describing (a) the contractile forces that endothelial cells exert on the ECM, (b) the resulting strains in the extracellular matrix, and (c) the cellular response to the strains, suffices for reproducing the behavior of individual endothelial cells and the interactions of endothelial cell pairs in compliant matrices. With the same set of rules, the model also reproduces network formation from scattered cells, and sprouting from endothelial spheroids. Combining the present mechanical model with aspects of previously proposed mechanical and chemical models may lead to a more complete understanding of in vitro angiogenesis.Comment: 25 pages, 6 figures, accepted for publication in PLoS Computational Biolog

Development of an Approach for the Holistic Assessment of Innovation Projects in Manufacturing Including Potential, Effort, and Risk Using a Systematic Literature Review and Expert Interviews

Manufacturing companies face severe challenges from rapid technological developments. Industry 5.0 indicates the need for a sustainable, human-centered, and resilient industry. In striving for transformation, innovation becomes critical. However, a careful allocation of resources implies the evaluation of innovation projects. Moreover, diverse types of innovation and limited amounts of information represent a significant challenge. Therefore, this contribution presents an approach for holistically assessing innovation in manufacturing. First, a systematic literature review (SLR) was conducted to frame the current research state and identify assessment criteria. Second, a multiple-attribute decision-making method (MADM) was developed using the findings of the SLR and expert interviews. Finally, the criteria and the assessment approach were verified and validated by expert interviews, a workshop, and an industrial use case application. As the main findings, three criteria groups were derived and detailed: potentials, efforts, and risks. These criteria groups were used in a MADM approach incorporating Fuzzy set theory within a hybrid technique, combining the Analytical Hierarchical Process with the Technique for Order Preference by Similarity to Ideal Solutions. In conclusion, an enhancement of innovation assessment in manufacturing was achieved through the integration of different criteria and the balance between complexity and industrial applicability

Heterogeneous nucleation of the primary phase in the rapid solidification of Al-4.5wt%Cu alloy droplet

International audienceThis paper reports on rapid solidification of Al-Cu alloys. A heterogeneous nucleation/growth model coupled with a thermal model of a falling droplet through a stagnant gas was developed. The primary undercooling as well as the number of nucleation points was compared with Al-Cu alloy droplets produced by Impulse Atomization (IA). Based on experimental results from Neutron Diffraction, secondary (eutectic) phases were obtained. Then, primary and secondary undercoolings were estimated using the metastable extensions of solidus and liquidus lines calculated by Thermo-Calc. Moreover, Synchrotron X-ray micro-tomography has been performed on Al-4.5wt%Cu droplets. The undercoolings are in good agreement. Results also evidence the presence of one nucleation point and are in agreement with the experimental observations. 1. Introduction Manufacturing of most metallic alloy products involves solidification at some stage. Mechanical properties of these products are generally related to their solidification microstructures. Depending on the final application of a product, a certain type of microstructure is more appropriate compared to another. For a product that requires directional properties, a microstructure of columnar grains is needed while isotropic properties are satisfied with an equiaxed structure. Generally, post-processing of the solidified materials is required to obtain the final product with desired properties. These post-solidification treatments are generally time-consuming and therefore increase the production cost without fully eliminating solidification related defects such as segregation. Therefore, it is important to understand all the dynamics involved in the formation of solidification microstructures in order to control the properties of the final products. As dendrites growth from an undercooled melt depends a great deal on the nucleation undercooling. Therefore, determination of undercooling and the resulting growth rate, recalescence, microsegregation/phase fraction and grain size is very important. Al-Cu alloys (4.5, 5, 10 and 17 wt% Cu) have been produced by IA and the last three compositions were analysed in our previous papers [1, 2]. IA is a single fluid atomization technique that is capable of producing droplets of controlled size having a relatively narrow distribution and a predictable cooling rate. The alloys (350 to 450g) were melted in a graphite crucible by means of an induction furnace and atomized at 850ºC in an almost oxygen free chamber (10ppm) under Nitrogen, Helium or Argon atmospheres. The atomized droplets rapidly solidify during their fall by losing heat to th

Political institutions and debt crises

This paper shows that political institutions matter in explaining defaults on external and domestic debt obligations. We explore a large number of political and macroeconomic variables using a non-parametric technique to predict safety from default. The advantage of this technique is that it is able to identify patterns in the data that are not captured in standard probit analysis. We find that political factors matter, and do so in different ways for democratic and non-democratic regimes, and for domestic and external debt. In democracies, a parliamentary system or sufficient checks and balances almost guarantee the absence of default on external debt when economic fundamentals or liquidity are sufficiently strong. In dictatorships, high stability and tenure play a similar role for default on domestic debt

The European sea bass <i>Dicentrarchus labrax</i> genome puzzle: comparative BAC-mapping and low coverage shotgun sequencing

BackgroundFood supply from the ocean is constrained by the shortage of domesticated and selected fish. Development of genomic models of economically important fishes should assist with the removal of this bottleneck. European sea bass Dicentrarchus labrax L. (Moronidae, Perciformes, Teleostei) is one of the most important fishes in European marine aquaculture; growing genomic resources put it on its way to serve as an economic model.ResultsEnd sequencing of a sea bass genomic BAC-library enabled the comparative mapping of the sea bass genome using the three-spined stickleback Gasterosteus aculeatus genome as a reference. BAC-end sequences (102,690) were aligned to the stickleback genome. The number of mappable BACs was improved using a two-fold coverage WGS dataset of sea bass resulting in a comparative BAC-map covering 87% of stickleback chromosomes with 588 BAC-contigs. The minimum size of 83 contigs covering 50% of the reference was 1.2 Mbp; the largest BAC-contig comprised 8.86 Mbp. More than 22,000 BAC-clones aligned with both ends to the reference genome. Intra-chromosomal rearrangements between sea bass and stickleback were identified. Size distributions of mapped BACs were used to calculate that the genome of sea bass may be only 1.3 fold larger than the 460 Mbp stickleback genome.ConclusionsThe BAC map is used for sequencing single BACs or BAC-pools covering defined genomic entities by second generation sequencing technologies. Together with the WGS dataset it initiates a sea bass genome sequencing project. This will allow the quantification of polymorphisms through resequencing, which is important for selecting highly performing domesticated fish