6,275 research outputs found
Optimization of an Electromagnetic Energy Harvesting Device
This paper presents the modeling and optimization of an electromagnetic-based generator for generating power from ambient vibrations. Basic equations describing such generators are presented and the conditions for maximum power generation are described. Two-centimeter scale prototype generators, which consist of magnets suspended on a beam vibrating relative to a coil, have been built and tested. The measured power and modeled results are compared. It is shown that the experimental results confirm the optimization theory
A comparative study of angle dependent magnetoresistance in [001] and [110]
The angle dependent magnetoresistance study on [001] and [110] LaSrMnO thin films show that the anisotropy energy of [110]
films is higher when compared with a [001] oriented LaSrMnO film of similar thickness. The data has been analyzed in the light
of multidomain model and it is seen that this model correctly explains the
observed behavior.Comment: 8pages, 2 figure
Microelectromechanical systems vibration powered electromagnetic generator for wireless sensor applications
This paper presents a silicon microgenerator, fabricated using standard silicon micromachining techniques, which converts external ambient vibrations into electrical energy. Power is generated by an electromagnetic transduction mechanism with static magnets positioned on either side of a moving coil, which is located on a silicon structure designed to resonate laterally in the plane of the chip. The volume of this device is approximately 100 mm3. ANSYS finite element analysis (FEA) has been used to determine the optimum geometry for the microgenerator. Electromagnetic FEA simulations using Ansoft’s Maxwell 3D software have been performed to determine the voltage generated from a single beam generator design. The predicted voltage levels of 0.7–4.15 V can be generated for a two-pole arrangement by tuning the damping factor to achieve maximum displacement for a given input excitation. Experimental results from the microgenerator demonstrate a maximum power output of 104 nW for 0.4g (g=9.81 m s1) input acceleration at 1.615 kHz. Other frequencies can be achieved by employing different geometries or material
Critically phase-matched Ti:sapphire-laserpumped deep-infrared femtosecond optical parametric oscillator based on CdSiP2
We report a high-repetition-rate femtosecond optical parametric oscillator (OPO) for the deep-infrared (deep-IR) based on type-I critical phase-matching in CdSiP2 (CSP), pumped directly by a Ti:sapphire laser. Using angle-tuning in the CSP crystal, the OPO can be continuously tuned across 7306–8329 nm (1201–1369 cm−1) in the deep-IR. It delivers up to 18 mW of idler average power at 7306 nm and >7 mW beyond 8000 nm at 80.5 MHz repetition rate, with the spectra exhibiting bandwidths of >150 nm across the tuning range. Moreover, the signal is tunable across 1128–1150 nm in the near-infrared, providing up to 35 mW of average power in ∼266 fs pulses at 1150 nm. Both beams exhibit single-peak Gaussian distribution in TEM00 spatial profile. With an equivalent spectral brightness of ∼5.6×1020photons s−1 mm−2 sr−10.1% BW−1, this OPO represents a viable alternative to synchrotron and supercontinuum sources for deep-IR applications in spectroscopy, metrology, and medical diagnostics.Peer ReviewedPostprint (author's final draft
Fiber-Flux Diffusion Density for White Matter Tracts Analysis: Application to Mild Anomalies Localization in Contact Sports Players
We present the concept of fiber-flux density for locally quantifying white
matter (WM) fiber bundles. By combining scalar diffusivity measures (e.g.,
fractional anisotropy) with fiber-flux measurements, we define new local
descriptors called Fiber-Flux Diffusion Density (FFDD) vectors. Applying each
descriptor throughout fiber bundles allows along-tract coupling of a specific
diffusion measure with geometrical properties, such as fiber orientation and
coherence. A key step in the proposed framework is the construction of an FFDD
dissimilarity measure for sub-voxel alignment of fiber bundles, based on the
fast marching method (FMM). The obtained aligned WM tract-profiles enable
meaningful inter-subject comparisons and group-wise statistical analysis. We
demonstrate our method using two different datasets of contact sports players.
Along-tract pairwise comparison as well as group-wise analysis, with respect to
non-player healthy controls, reveal significant and spatially-consistent FFDD
anomalies. Comparing our method with along-tract FA analysis shows improved
sensitivity to subtle structural anomalies in football players over standard FA
measurements
Femtosecond deep-infrared optical parametric oscillator pumped directly by a Ti:sapphire laser
We report a high-repetition-rate femtosecond optical parametric oscillator (OPO) for the deep-infrared (deep-IR) based on the nonlinear optical crystal, CdSiP2 (CSP), pumped directly by a Ti:sapphire laser, for the first time. By pumping CSP at <1 μm, we have achieved practical output powers at the longest wavelengths generated by any Ti:sapphire-pumped OPO. Using a combination of pump wavelength tuning, type-I critical phase-matching, and cavity delay tuning, we have generated continuously tunable radiation across 6654−8373 nm (1194−1503 cm-1) at 80.5 MHz repetition rate, providing up to 20 mW of average power at 7314 nm and <7 mW beyond 8000 nm, with idler spectra exhibiting bandwidths of 140−180 nm across the tuning range. Moreover, the near-IR signal is tunable across 1127−1192 nm, providing up to 37 mW of average power at 1150 nm. Signal pulses, characterised using intensity autocorrelation, have durations of ∼260–320 fs, with corresponding time-bandwidth product of ∆υ∆τ∼1. The idler and signal output exhibit a TEM00 spatial profile with single-peak Gaussian distribution. With an equivalent spectral brightness of ∼6.68×1020 photons s-1 mm-2 sr-1 0.1% BW-1, this OPO represents a viable table-top alternative to synchrotron and supercontinuum sources for deep-IR applications in spectroscopy, metrology and medical diagnostics.Peer ReviewedPostprint (author's final draft
Quantum matchgate computations and linear threshold gates
The theory of matchgates is of interest in various areas in physics and
computer science. Matchgates occur in e.g. the study of fermions and spin
chains, in the theory of holographic algorithms and in several recent works in
quantum computation. In this paper we completely characterize the class of
boolean functions computable by unitary two-qubit matchgate circuits with some
probability of success. We show that this class precisely coincides with that
of the linear threshold gates. The latter is a fundamental family which appears
in several fields, such as the study of neural networks. Using the above
characterization, we further show that the power of matchgate circuits is
surprisingly trivial in those cases where the computation is to succeed with
high probability. In particular, the only functions that are
matchgate-computable with success probability greater than 3/4 are functions
depending on only a single bit of the input
Fluoride-containing bioactive glasses: Effect of glass design and structure on degradation, pH and apatite formation in simulated body fluid
NOTICE: this is the author’s version of a work that was accepted for publication in Acta Biomaterialia. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Acta Biomaterialia, [VOL 6, ISSUE 8, (2010)] DOI: 10.1016/j.actbio.2010.01.04
Recommended from our members
Diurnal Refractive Error Fluctuations in Diabetic and Control Subjects
Purpose: Refractive error has been shown to fluctuate in poorly controlled diabetic patients. The purpose of this study was to measure acute diurnal fluctuations in refractive error and blood glucose levels (BGLs) in diabetic and control subjects.
Methods: Twenty-one type 2 diabetic subjects (age 56 ± 11 years), 20 type 1 diabetic subjects (age 38 ± 15 years) and 20 non-diabetic controls (age 49 ± 23 years) took part in the study. Refractive error was measured with an OPD ARK-10000 autorefractometer (Nidek) and BGLs were measured using a finger stick test (Hemocue). All measurements were taken six times during the day, between 8AM and 8PM at approximately twohourly intervals. Using power vector analysis the variability in refractive error was mapped against time of day and related to BGLs, HbA1c, diabetic status and duration of disease.
Results: Refractive error was similar between groups (p=0.96) and did not fluctuate significantly during the day in any of the three groups (ANOVA p>0.05). The mean ± SD values for BGLs during the day were 10.4 ± 4.40mM/l in DM type 2, 10.3 ± 5.30mM/l in DM type 1, and 5.4 ± 1.04mM/l in control subjects. BGLs changed significantly during the day and between groups (ANOVA p0.05). Multiple regression analysis showed that neither BGLs, HbA1c, diabetic status, nor duration of disease had a significant effect on diurnal refractive error measurements. (p>0.05).
Conclusions: Diurnal changes in BGLs do not result in significant acute refractive error fluctuations in diabetic patients, as measured with an autorefractometer.
CR: C. O’Donnell, None; H. Workman, None; S.L. Hosking, None; B. Huntjens, None.
Support: Supported by a PhD studentship from Lein Applied Diagnostics Ltd
- …