62,135 research outputs found
Calculation of accurate permanent dipole moments of the lowest states of heteronuclear alkali dimers using extended basis sets
The obtention of ultracold samples of dipolar molecules is a current
challenge which requires an accurate knowledge of their electronic properties
to guide the ongoing experiments. In this paper, we systematically investigate
the ground state and the lowest triplet state of mixed alkali dimers (involving
Li, Na, K, Rb, Cs) using a standard quantum chemistry approach based on
pseudopotentials for atomic core representation, gaussian basis sets, and
effective terms for core polarization effects. We emphasize on the convergence
of the results for permanent dipole moments regarding the size of the gaussian
basis set, and we discuss their predicted accuracy by comparing to other
theoretical calculations or available experimental values. We also revisit the
difficulty to compare computed potential curves among published papers, due to
the differences in the modelization of core-core interaction.Comment: accepted to J. Chem. Phy
Waveform simulator Patent
Sign wave generation simulator for variable amplitude, frequency, damping, and phase pulses for oscilloscope displa
Performance tests of a single-cylinder compression-ignition engine with a displacer piston
Engine performance was investigated using a rectangular displacer on the piston crown to cause a forced air flow in a vertical-disk combustion chamber of a single-cylinder, 4-stroke-cycle compression-ignition engine. The optimum air-flow area was determined first with the area concentrated at one end of the displacer and then with the area equally divided between two passages, one at each end of the displacer. Best performance was obtained with the two-passage air flow arranged to give a calculated maximum air-flow speed of 8 times the linear crank-pin speed. With the same fuel-spray formation as used without the air flow, the maximum clear exhaust brake mean effective pressure at 1,500 r.p.m. was increased from 90 to 115 pounds per square inch and the corresponding fuel consumption reduced from 0.46 to 0.43 pound per brake horsepower-hour. At 1,200 r.p.m., a maximum clear exhaust brake mean effective pressure of 120 pounds per square inch was obtained at a fuel consumption of 0.42 pound per brake horsepower-hour. At higher specific fuel consumption the brake mean effective pressure was still increasing rapidly
Fourier-transform spectroscopy of Sr2 and revised ground state potential
Precise potentials for the ground state X1Sigma+g and the minimum region of
the excited state 2_1Sigma+u of Sr2 are derived by high resolution
Fourier-transform spectroscopy of fluorescence progressions from single
frequency laser excitation of Sr2 produced in a heat pipe at 950 Celsius. A
change of the rotational assignment by four units compared to an earlier work
(G. Gerber, R. M\"oller, and H. Schneider, J. Chem. Phys. 81, 1538 (1984)) is
needed for a consistent description leading to a significant shift of the
potentials towards longer inter atomic distances. The huge amount of ground
state data derived for the three different isotopomers 88Sr2, 86Sr88Sr and
87Sr88Sr (almost 60% of all excisting bound rovibrational ground state levels
for the isotopomer 88Sr2) fixes this assignment undoubtedly. The presented
ground state potential is derived from the observed transitions for the radial
region from 4 to 11 A (9 cm-1 below the asymptote) and is extended to the longe
range region by the use of theoretical dispersion coefficients together with
already available photoassociation data. New estimations of the scattering
lengths for the complete set of isotopic combinations are derived by mass
scaling with the derived potential. The data set for the excited state
2_1Sigma+u was sufficient to derive a potential energy curve around the
minimum.Comment: 10 pages, 7 figures, some small corrections done especially to the
potential description of the excited state (already included in the published
journal version
The Effect of Connecting-passage Diameter on the Performance of a Compression-ignition Engine with a Precombustion Chamber
Results of motoring tests are presented showing the effect of passage diameter on chamber and cylinder compression pressures, maximum pressure differences, and f.m.e.p. over a speed range from 300 to 1,750 r.p.m. Results of engine performance tests are presented which show the effect of passage diameter on m.e.p., explosion pressures, specific fuel consumption, and rates of pressure rise for a range of engine speeds from 500 to 1,500 r.p.m. The cylinder compression pressure, the maximum pressure difference, and the f.m.e.p. decreased rapidly as the passage diameter increased to 29/64 inch, whereas further increase in passage diameter effected only a slight change. The most suitable passage diameter for good engine performance and operating characteristics was 29/64 inch. Passage diameter became less critical with a decrease in engine speed. Therefore, the design should be based on maximum operating speed. Optimum performance and satisfactory combustion control could not be obtained by means of any single diameter of the connecting passage
Reducing the numerical effort of finite-temperature density matrix renormalization group transport calculations
Finite-temperature transport properties of one-dimensional systems can be
studied using the time dependent density matrix renormalization group via the
introduction of auxiliary degrees of freedom which purify the thermal
statistical operator. We demonstrate how the numerical effort of such
calculations is reduced when the physical time evolution is augmented by an
additional time evolution within the auxiliary Hilbert space. Specifically, we
explore a variety of integrable and non-integrable, gapless and gapped models
at temperatures ranging from T=infty down to T/bandwidth=0.05 and study both
(i) linear response where (heat and charge) transport coefficients are
determined by the current-current correlation function and (ii) non-equilibrium
driven by arbitrary large temperature gradients. The modified DMRG algorithm
removes an 'artificial' build-up of entanglement between the auxiliary and
physical degrees of freedom. Thus, longer time scales can be reached
Finite temperature dynamical DMRG and the Drude weight of spin-1/2 chains
We propose an easily implemented approach to study time-dependent correlation
functions of one dimensional systems at finite temperature T using the density
matrix renormalization group. The entanglement growth inherent to any
time-dependent calculation is significantly reduced if the auxiliary degrees of
freedom which purify the statistical operator are time evolved with the
physical Hamiltonian but reversed time. We exploit this to investigate the long
time behavior of current correlation functions of the XXZ spin-1/2 Heisenberg
chain. This allows a direct extraction of the Drude weight D at intermediate to
large T. We find that D is nonzero -- and thus transport is dissipationless --
everywhere in the gapless phase. At low temperatures we establish an upper
bound to D by comparing with bosonization
A study of earth radar returns from Alouette satellite
Ground radar reflection coefficient analysis on Alouette sounder ionogram
The Effect of Clearance Distribution on the Performance of a Compression-ignition Engine with a Precombustion Chamber
The clearance distribution in a precombustion chamber cylinder head was varied so that for a constant compression ratio of 13.5 the spherical auxiliary chambers contained 20, 35, 50, and 70 per cent of the total clearance volume. Each chamber was connected to the cylinder by a single circular passage, flared at both ends, and of a cross-sectional area proportional to the chamber volume, thereby giving the same calculated air-flow velocity through each passage. Results of engine-performance tests are presented with variations of power, fuel consumption, explosion pressure, rate of pressure rise, ignition lag, heat loss to the cooling water, and motoring characteristics. For good performance the minimum auxiliary chamber volume, with the cylinder head design used, was 35 per cent of the total clearance volume; for larger volumes the performance improves but slightly. With the auxiliary chamber that contained 35 percent of the clearance volume there were obtained the lowest explosion pressures, medium rates of pressure rise, and slightly less than the maximum power. For all clearance distributions an increase in engine speed decreased the ignition lag in seconds and increased the rate of pressure rise
Heat transfer across surfaces in contact - Practical effects of transient temperature and pressure environments Semiannual report, 1 Oct. 1965 - 1 Apr. 1966
Heat transfer across metal surfaces under transient temperature and pressure environmen
- …