Effect of type of load on stress analysis of thin-walled ducts

The standard procedure for qualifying the design of duct (pipe) systems in the Space Shuttle Main Engine (SSME) has been fairly well defined. However, since pipe elbows are quite common and important in the SSME duct systems, a clear understanding of the detailed stress profile of the components is necessary for accurate structural and life assessments. This study was initiated to predict the stress profile at/near the tangent point along the cross section of the duct under various types of loads. Also, this study was further extended to understand the stiffening effect on stresses due to pressure at the tangent point. The intention of this study was to identify the importance of selecting proper locations for mounting strain gauges and to utilize the obtained results to anchor dynamic models for accurate structural and life assessments of the SSME ducts under a dynamic environment. The finite element method was utilized in this study

Electronic structures of antiperovskite superconductors: MgXNi3_3 (X=B,C,N)

We have investigated electronic structures of a newly discovered antiperovskite superconductor MgCNi$_3$ and related compounds MgBNi$_3$ and MgNNi$_3$. In MgCNi$_3$, a peak of very narrow and high density of states is located just below $\rm E_F$, which corresponds to the $\pi^*$ antibonding state of Ni-3d and C-$2p$ but with the predominant Ni-3d character. The prominent nesting feature is observed in the $\Gamma$-centered electron Fermi surface of an octahedron-cage-like shape that originates from the 19th band. The estimated superconducting parameters based on the simple rigid-ion approximation are in reasonable agreement with experiment, suggesting that the superconductivity in MgCNi$_3$ is described well by the conventional phonon mechanism.Comment: 5 pages, 5 figure

Ultralow-threshold erbium-implanted toroidal microlaser on silicon

We present an erbium-doped microlaser on silicon operating at a wavelength of 1.5 mum that operates at a launched pump threshold as low as 4.5 muW. The 40 mum diameter toroidal microresonator is made using a combination of erbium ion implantation, photolithography, wet and dry etching, and laser annealing, using a thermally grown SiO2 film on a Si substrate as a starting material. The microlaser, doped with an average Er concentration of 2x10^(19) cm(-3), is pumped at 1480 nm using an evanescently coupled tapered optical fiber. Cavity quality factors as high as 3.9x10^(7) are achieved, corresponding to a modal loss of 0.007 dB/cm, and single-mode lasing is observed

Electronic Structures of Antiperovskite Superconductor MgCNi3_3 and Related Compounds

Electronic structure of a newly discovered antiperovskite superconductor MgCNi$_3$ is investigated by using the LMTO band method. The main contribution to the density of states (DOS) at the Fermi energy $E_{\rm F}$ comes from Ni 3$d$ states which are hybridized with C 2$p$ states. The DOS at $E_{\rm F}$ is varied substantially by the hole or electron doping due to the very high and narrow DOS peak located just below $E_{\rm F}$. We have also explored electronic structures of C-site and Mg-site doped MgCNi$_3$ systems, and described the superconductivity in terms of the conventional phonon mechanism.Comment: 3 pages, presented at ORBITAL2001 September 11-14, 2001 (Sendai, JAPAN

On construction of optimal mixed-level supersaturated designs

Supersaturated design (SSD) has received much recent interest because of its potential in factor screening experiments. In this paper, we provide equivalent conditions for two columns to be fully aliased and consequently propose methods for constructing $E(f_{\mathrm{NOD}})$- and $\chi^2$-optimal mixed-level SSDs without fully aliased columns, via equidistant designs and difference matrices. The methods can be easily performed and many new optimal mixed-level SSDs have been obtained. Furthermore, it is proved that the nonorthogonality between columns of the resulting design is well controlled by the source designs. A rather complete list of newly generated optimal mixed-level SSDs are tabulated for practical use.Comment: Published in at http://dx.doi.org/10.1214/11-AOS877 the Annals of Statistics (http://www.imstat.org/aos/) by the Institute of Mathematical Statistics (http://www.imstat.org

Electronic structure of metallic antiperovskite compound GaCMn3_3

We have investigated electronic structures of antiperovskite GaCMn$_3$ and related Mn compounds SnCMn$_3$, ZnCMn$_3$, and ZnNMn$_3$. In the paramagnetic state of GaCMn$_3$, the Fermi surface nesting feature along the $\Gamma{\rm R}$ direction is observed, which induces the antiferromagnetic (AFM) spin ordering with the nesting vector {\bf Q} $\sim \Gamma{\rm R}$. Calculated susceptibilities confirm the nesting scenario for GaCMn$_3$ and also explain various magnetic structures of other antiperovskite compounds. Through the band folding effect, the AFM phase of GaCMn$_3$ is stabilized. Nearly equal densities of states at the Fermi level in the ferromagnetic and AFM phases of GaCMn$_3$ indicate that two phases are competing in the ground state.Comment: 4 pages, 5 figure

Parametric study in weld mismatch of longitudinally welded SSME HPFTP inlet

Welded joints are an essential part of pressure vessels such as the Space Shuttle Main Engine (SSME) Turbopumps. Defects produced in the welding process can be detrimental to weld performance. Recently, review of the SSME high pressure fuel turbopump (HPFTP) titanium inlet x rays revealed several weld discrepancies such as penetrameter density issues, film processing discrepancies, weld width discrepancies, porosity, lack of fusion, and weld offsets. Currently, the sensitivity of welded structures to defects is of concern. From a fatigue standpoint, weld offset may have a serious effect since local yielding, in general, aggravates cyclic stress effects. Therefore, the weld offset issue is considered. Using the finite element method and mathematical formulations, parametric studies were conducted to determine the influence of weld offsets and a variation of weld widths in longitudinally welded cylindrical structures with equal wall thickness on both sides of the joint. From the study, the finite element results and theoretical solutions are presented