Mechanical properties of magnesium-based wood-like material subjected to splitting tensile tests

To investigate the splitting tensile characteristics of a new building material, namely magnesium-based wood-like material (MWM), the cubic splitting tensile tests were carried out at a loading rate of 200 N/s. Full-field displacements and crack behaviors were measured using Digital Image Correlation, and the splitting tensile strength is 1.79 MPa. The elastic Young modulus, Poisson’s ratio, and axial compressive strength were measured as 2.21 GPa, 0.21, 8.76 MPa respectively. In the splitting tensile tests, primary cracks were observed to initiate from the geometric centre of the specimen and then extend to the loading ends where secondary cracks appeared. A new method for identifying cracking modes showed the secondary cracks were mainly caused by shear and tensile-shear failure, whereas the primary cracks were caused by tensile failure. An accurate method for estimating the elastic Young modulus, simultaneously with the determination of the splitting tensile strength of MWM cubes is proposed

An iterative method for reference pattern selection in high-resolution electron backscatter diffraction (HR-EBSD)

For high (angular) resolution electron backscatter diffraction (HR-EBSD), the selection of a reference diffraction pattern (EBSP0) significantly affects the precision of the calculated strain and rotation maps. This effect was demonstrated in plastically deformed body-centred cubic and face-centred cubic ductile metals (ferrite and austenite grains in duplex stainless steel) and brittle single-crystal silicon, which showed that the effect is not only limited to measurement magnitude but also spatial distribution. An empirical relationship was then identified between the cross-correlation parameter and angular error, which was used in an iterative algorithm to identify the optimal reference pattern that maximises the precision of HR-EBSD

HR-EBSD analysis of in situ stable crack growth at the micron scale

Understanding the local fracture resistance of microstructural features. such as brittle inclusions, coatings, and interfaces at the microscale under complex loading conditions is critical for microstructure-informed design of materials. In this study, a novel approach has been formulated to decompose the J-integral evaluation of the elastic energy release rate to the three-dimensional stress intensity factors directly from experimental measurements of the elastic deformation gradient tensors of the crack field by in situ high (angular) resolution electron backscatter diffraction (HR-EBSD). An exemplar study is presented of a quasi-static crack, inclined to the observed surface, propagating on low index {hkl} planes in a (001) single crystal silicon wafer

Application of neutron imaging to detect and quantify fatigue cracking

Non-destructive imaging techniques provide a unique opportunity to study crack initiation and propagation behaviour in structural materials. To evaluate the applicability of different volumetric imaging techniques, a round bar notched sample of duplex stainless steel was fatigue cracked and studied in situ and ex situ. Neutron and synchrotron X-ray tomography was used along with destructive methods and Bragg edge neutron imaging to evaluate the fatigue crack. Neutron attenuation tomography obtained a three-dimensional image in which the crack was readily identifiable. The neutron tomography, although lower in spatial resolution compared with the X-ray synchrotron tomography and requiring higher acquisition time, is sensitive to the phase chemistry, and has the potential to study engineering size components. Bragg edge neutron transmission imaging allows for the mapping of two-dimensional elastic strains and was used to identify the fatigue crack from the reduction in the strain in the region where the crack propagated. A finite element model of the cracked specimen was used to simulate the average through thickness strain that is measured by the Bragg edge neutron imaging technique. The strains measured in the ferritic phase correspond better with the simulation strains than the strain measured in the austenitic phase. It is concluded that this difference is due to strain partitioning, which is influenced by the strong texture present in the duplex steel

Imaging Sodium Dendrite Growth in All‐Solid‐State Sodium Batteries using 23Na T2‐weighted MRI

Two‐dimensional, Knight‐shifted, T2‐contrasted 23Na magnetic resonance imaging of an all‐solid‐state cell with Na electrode and a ceramic electrolyte is employed to directly observe Na microstructural growth. A spalling dendritic morphology is observed and confirmed by more conventional post‐mortem analysis; X‐ray tomography and scanning electron microscopy. A significantly greater 23Na T2 for the dendritic growth, compared with the bulk metal electrode, is attributed to increased sodium ion mobility in the dendrite. 23Na T2‐contrast MRI of metallic sodium offers a clear, routine method for observing and isolating microstructural growths and can supplement the current suite of techniques utilised to analyse dendritic growth in all‐solid‐state cells

Influence of contouring the lithium metal/solid electrolyte interface on the critical current for dendrites

Contouring or structuring of the lithium/ceramic electrolyte interface and therefore increasing its surface area has been considered as a possible strategy to increase the charging current in solid-state batteries without lithium dendrite formation and short-circuit. By coupling together lithium deposition kinetics and the me chanics of lithium creep within calculations of the current distribution at the interface, and leveraging a model for lithium dendrite growth, we show that efforts to avoid dendrites on charging by increasing the interfacial surface area come with significant limitations associated with the topography of rough surfaces. These limitations are sufficiently severe such that it is very unlikely contouring could increase charging currents while avoiding dendrites and short-circuit to the levels required. For example, we show a sinusoidal surface topography can only raise the charging current before dendrites occur by approx. 50% over a flat interface

Influence of contouring the lithium metal/solid electrolyte interface on the critical current for dendrites

Contouring or structuring of the lithium/ceramic electrolyte interface and therefore increasing its surface area has been considered as a possible strategy to increase the charging current in solid-state batteries without lithium dendrite formation and short-circuit. By coupling together lithium deposition kinetics and the me chanics of lithium creep within calculations of the current distribution at the interface, and leveraging a model for lithium dendrite growth, we show that efforts to avoid dendrites on charging by increasing the interfacial surface area come with significant limitations associated with the topography of rough surfaces. These limitations are sufficiently severe such that it is very unlikely contouring could increase charging currents while avoiding dendrites and short-circuit to the levels required. For example, we show a sinusoidal surface topography can only raise the charging current before dendrites occur by approx. 50% over a flat interface

Decoupling, quantifying, and restoring aging-induced Zn-anode losses in rechargeable aqueous zinc batteries

The search for batteries beyond Li-ion that offer better performance, reliability, safety, and/or affordability has led researchers to explore a diverse array of candidates. The advantages of Zn-ion batteries reside in zinc’s relatively low reactivity, raising the prospect of a rechargeable battery with a simple aqueous electrolyte and a cheaper, safer option to the organic electrolytes that must be paired with reactive lithium. However, water still reacts with the zinc in corrosion reactions. These consume zinc, lowering the battery’s capacity, and generate gas that accumulates in the sealed cell. We diagnose the contribution of corrosion to performance decay in zinc batteries and reveal the critical role of gas accumulation in deactivating large sections of electrode, which cripples cell performance. Fortunately, electrodes can be reactivated by removal of the gas, demonstrating the importance of designing future cells that either prevent gas formation or facilitate its safe release

Coevolution in a One Predator–Two Prey System

Background: Our understanding of coevolution in a predator–prey system is based mostly on pair-wise interactions. Methodology and Principal Findings: Here I analyze a one-predator–two-prey system in which the predator’s attack ability and the defense abilities of the prey all evolve. The coevolutionary consequences can differ dramatically depending on the initial trait value and the timing of the alternative prey’s invasion into the original system. If the invading prey species has relatively low defense ability when it invades, its defense is likely to evolve to a lower level, stabilizing the population dynamics. In contrast, if when it invades its defense ability is close to that of the resident prey, its defense can evolve to a higher level and that of the resident prey may suddenly cease to evolve, destabilizing the population dynamics. Destabilization due to invasion is likely when the invading prey is adaptively superior (evolution of its defense is less constrained and fast), and it can also occur in a broad condition even when the invading prey is adaptively inferior. In addition, invasion into a resident system far from equilibrium characterized by population oscillations is likely to cause further destabilization