19,070 research outputs found
Quick disconnect latch and handle combination Patent
Quick disconnect latch and handle combination for mounting articles on walls or supporting bases in spacecraft under zero gravity condition
Periodic minimal surfaces of cubic symmetry
A survey of cubic minimal surfaces is presented, based on the concept of fundamental surface patches and their relation to the asymmetric units of the space groups. The software Surface Evolver has been used to test for stability and to produce graphic displays. Particular emphasis is given to those surfaces that can be generated by a finite piece bounded by straight
lines. Some new varieties have been found and a systematic nomenclature is introduced, which provides a symbol (a ‘gene’) for each triply-periodic minimal surface that specifies the surface unambiguously
The full set of -invariant factorized -matrices
We use the method of the tensor product graph to construct rational (Yangian
invariant) solutions of the Yang-Baxter equation in fundamental representations
of and thence the full set of -invariant factorized -matrices.
Brief comments are made on their bootstrap structure and on Belavin's scalar
Yangian conserved charges.Comment: 10p
Diffusion and convection of gaseous and fine particulate from a chimney
Particle dispersion from a high chimney is considered and an expression for the subsequent concentration of the particulate deposited on the ground is derived. We consider the general case wherein the effects of both diffusion and convection on the steady state ground concentration of particulate are incorporated. Two key parameters emerge from this analysis: the ratio of diffusion to convection and the nondimensionalised surface mass transfer rate. We also solve the inverse problem of recovering these two parameters given the boundary concentration profile and provide an estimate of the concentration flux above the chimney stack
Heat treatment study of the SiC/Ti-15-3 composite system
The oxidation and aging behaviors of a continuous fiber SiC/Ti-15V-3Cr-3Sn-3Al composite (SiC/Ti-15-3) were investigated. The aging characteristic of the composite were compared with those of the unreinforced Ti-15-3 matrix material, which was processed in the same manner as the composite. Various age hardened conditions of both the unreinforced matrix and the composite were evaluated by using optical microscopy, hardness measurements, and room temperature tensile tests (unreinforced matrix only). The Ti-15-3 material formed a thick surface oxide at temperature at or above 550 C when heat treated in air. The in situ composite matrix was softer than the unreinforced matrix for equivalent aging conditions. Both materials hardened to a maximum, then softened during overaging. The temperature at which peak aging occurred was approx. 450 C for both the in situ composite matrix and the unreinforced matrix. The room temperature elastic modulus and ultimate tensile strength of the unreinforced matrix varied as a function of aging treatment and paralleled the hardness behavior. The modulus and tensile strength showed little response to aging up to temperatures of 300 C; however, these properties increased after aging at 550 C. Aging at temperatures above 550 C resulted in a decrease in the modulus and tensile strength. The failure strain was a function of the precipitation state and of the amount of oxidation resulting from the heat treatment. Aging in air at the higher temperatures (greater than 550 C) caused the formation of a thick oxide layer and reduced the ductility. Aging in vacuum at these temperatures resulted in significantly higher ductilities. Long term exposures at 700 C caused the formation of a large grain boundary alpha-phase which reduced the ductility, even though the specimens were heat treated in vacuum
Microstructure-property relationships in directionally solidified single crystal nickel-base superalloys
Some of the microstructural features which influence the creep properties of directionally solidified and single crystal nickel-base superalloys are discussed. Gamma precipitate size and morphology, gamma-gamma lattice mismatch, phase instability, alloy composition, and processing variations are among the factors considered. Recent experimental results are reviewed and related to the operative deformation mechanisms and to the corresponding mechanical properties. Special emphasis is placed on the creep behavior of single crystal superalloys at high temperatures, where directional gamma coarsening is prominent, and at lower temperatures, where gamma coarsening rates are significantly reduced. It can be seen that very subtle changes in microstructural features can have profound effects on the subsequent properties of these materials
- …