234 research outputs found
Characterizations on microencapsulated sunflower oil as self-healing agent using In situ polymerization method
This paper emphasizes the characterization on the microencapsulation of sunflower oil as self-healing agent. In-situ polymerization method mainly implicates in the microencapsulation
process. The analysis of microencapsulated sunflower oil via prominent characterization of yield of microcapsules, microcapsules characteristics and Fourier Transmission Infa-Red Spectroscopy (FTIR). The prime optimization used was reaction time of microencapsulation process in the ranges of 2, 3 and 4 h. The higher reaction time of microencapsulation process resulted in a higher yield of microcapsules. The yield of microcapsules increases from 46 to 53% respectively by the increasing of reaction time from 2 to 4 h. The surface morphology study associating the diameter of microcapsules measured to analyse the prepared microcapsules. It was indicated that microcapsules were round in shape with smooth micro-surfaces. It was discovered that the diameter of microcapsules during microencapsulation process after 4 h reaction time was in average of
70.53 μm. This size was measured before filtering the microcapsules with solvent and dried in vacuum oven. Apparently, after filtering and drying stage, the diameter of microcapsules specifically identified under Field Emission Scanning Electron Microscopy (FESEM) showing the size of 2.33 μm may be due to the removing the suspended oil surrounded the microcapsules. Sunflower oil as core content and urea formaldehyde (UF) as shell of microcapsules demonstrated the proven chemical properties on characterization by FTIR with the stretching peak of 1537.99 - 1538.90 cm-1 (-H in -CH2), 1235.49 - 1238.77 cm-1 (C-O-C Vibrations at Ester) and 1017.65 - 1034.11 cm-1 (C-OH Stretching Vibrations). It was showed that sunflower oil can be considered as an alternative nature resource for self-healing agent in microencapsulation process. The characterization of microencapsulated sunflower oil using in-situ polymerization method showed that sunflower oil was viable self-healing agent to be encapsulated and incorporated in metal coating
Extraction of biological hydroxyapatite from tuna fish bone for biomedical applications
Natural hydroxyapatite (HAp) is known for its common use in biomedical applications including in orthopaedic and implantation. HAp can be extracted from natural resources such as eggshells, fish bones and coral. Annually, it is found that huge amount of tuna fish bones was thrown away and being wasted as results from great consumption of tuna fish. In this study, tuna fish bones were extracted and characterised to be used in biomedical applications. Specifically, tuna fish bones were cleaned, and calcined at high temperature of 700 °C, 900 °C and 1100 °C. Powders
calcined at 700 °C showed pure HAp compared to powders calcined at 900 °C and 1100 °C which showed the presence of β-TCP. As temperature rising, the morphology of the powders also changes
from spherical-shaped to irregular-shaped indicated the substitution of phosphate and calcium from the β-TCP which also influenced the ratio of Ca/P obtained. In this study, powders calcined at 700 °C obtained optimum Ca/P ratio of 1.60. Moreover, EDS analysis showed the presence of tracer elements such as Ca, Mg, Sr Na, K and Zn in all calcined samples. These elements can help improve the biocompatibility of the HAp and beneficial for biomedical applications
A review of gelatin: properties, sources, process, applications, and commercialisation
This review begins with a discussion of the general properties of gelatin and its sources, particularly in
the food and health industries, and then briefly address the status quo of gelatin in today’s market.
Apart from the basic chemical compounds and gelatin types, this paper also discussed the commercialisation
of gelatin. This study also highlights the production of conventional gelatin and its current method
of processing, i.e. enzymatic hydrolysis. In addition, the variety of raw materials of collagen is outlined
and briefly broached the plant hydrocolloids which have been labeled as ’veggie-gelatin’. With regard
to the potential and market stability of gelatin, its recent studies are summarised in this paper.
Accordingly, this paper focuses on assessing the general utilities of the various sources of collagen as gelatin
derivatives. At that basis, the aim of this review is to provide an insight into gelatin in current applications,
market value and progress in gelatin extraction
Extraction of biological hydroxyapatite from bovine bone for biomedical applications
Current biomedical field demands intensive research on cost-effective and high availability materials to fulfil its various applications. Owing to its similar characteristic to human bone, biological hydroxyapatite (HAp) has been used as an alternative in bone replacement and implantation. In this study, biological HAp was extracted from bovine bones via calcination. Powders calcined at 700 °C and 900 °C showed the presence of HAp. The field emission scanning electron microscope (FESEM) analysis shows that the irregular morphology emerged and the size was increasing as the calcination temperature increased. By increasing the temperature of 1100 °C, β-TCP (beta-tricalcium phosphate) started to develop and influenced the ratio of Ca/P. At 900 °C, the Ca/P ratio obtained was 1.70, and closest to the theoretical ratio of Ca/P. The presence of trace elements like Ca, Mg, Sr Na, K and Zn in all samples are proved via energy-dispersive X-ray spectroscopy (EDS) analysis, and these elements help to enhance the bioactivity hence make it a good alternative in biomedical applications
Estimation and variation of saturation mixing ratio and mixing ratio over Potiskum, Nigeria
In this study, the monthly average mean temperature, relative humidity and surface pressure data obtained from the European Centre for Medium-Range Weather Forecasts (ECMWF) for a period of thirty-eight (1979 – 2016) years was employed to estimate the saturation mixing ratio and mixing ratio for Potiskum located in the Sahelian climatic zone of Nigeria. The monthly variation of saturation mixing ratio and mixing ratio with the meteorological parameters during the period under focused was investigated. The results revealed that the maximum and minimum values of saturation mixing ratio were found in the months of May and December with 31.7067 g kg-1 and 17.5980 g kg-1, respectively. The maximum and minimum values of saturation mixing ratio were found in the months of September and February with 20.6797 g kg-1 and 4.1153 g kg-1, respectively. The results showed that high values of mixing ratio were observed during the rainy season and low values during the dry season. The monthly variation of saturation mixing ratio with mean temperature and the monthly variation of mixing ratio with relative humidity depicts direct relationship. The monthly variation of saturation mixing ratio with atmospheric pressure and relative humidity and the monthly variation of mixing ratio with mean temperature and atmospheric pressure varies differently
Surface properties of alginate/chitosan biofilm for wound healing application
This work focuses on the fabrication of film based on natural
iopolymers for wound healing application. Alginate and chitosan were choosen because of their oustanding properties such as biocompatible, hydrophilic and non-toxic. Earlier, the biopolymer film was fabricated by using alginate 1% wt and chitosan 1% wt. solutions at volume ratios of 99:1 and 97:3. Next, the biopolymer film solution was cross-linked with 1 M CaCl 2.2H2O for two hours and later dried for 24 hours at room temperature. Then, the surface properties of the prepared biopolymer films were characterised via Field Emission Scanning Electron Microscopy (FESEM), Atomic Force Microscopy (AFM) and contact angle measurement. It was observed that the surface of the biopolymer film became rougher as the volume of the chitosan increases. This condition was confirmed with average surface roughness, RA for biopolymer film with ratio of 97:3 resulted in higher values. Also, it was found that the surface of biopolymer films were hydrophilic after the contact angle was less than 90°. This can be concluded that the biopolymer based on alginate/chitosan is a promising candidate for wound healing materials particularly with good surface properties for faster healing process at the wound areas
Recent advance in high manufacturing readiness level and high temperature CMOS mixed-signal integrated circuits on silicon carbide
A high manufacturing readiness level silicon carbide (SiC) CMOS technology is presented. The unique process flow enables the monolithic integration of pMOS and nMOS transistors with passive circuit elements capable of operation at temperatures of 300 °C and beyond. Critical to this functionality is the behaviour of the gate dielectric and data for high temperature capacitance–voltage measurements are reported for SiO2/4H-SiC (n and p type) MOS structures. In addition, a summary of the long term reliability for a range of structures including contact chains to both n-type and p-type SiC, as well as simple logic circuits is presented, showing function after 2000 h at 300 °C. Circuit data is also presented for the performance of digital logic devices, a 4 to 1 analogue multiplexer and a configurable timer operating over a wide temperature range. A high temperature micro-oven system has been utilised to enable the high temperature testing and stressing of units assembled in ceramic dual in line packages, including a high temperature small form-factor SiC based bridge leg power module prototype, operated for over 1000 h at 300 °C. The data presented show that SiC CMOS is a key enabling technology in high temperature integrated circuit design. In particular it provides the ability to realise sensor interface circuits capable of operating above 300 °C, accommodate shifts in key parameters enabling deployment in applications including automotive, aerospace and deep well drilling
Measurement of dijet photoproduction for events with a leading neutron at HERA
Differential cross sections for dijet photoproduction and this process in
association with a leading neutron, e+ + p -> e+ + jet + jet + X (+ n), have
been measured with the ZEUS detector at HERA using an integrated luminosity of
40 pb-1. The fraction of dijet events with a leading neutron was studied as a
function of different jet and event variables. Single- and double-differential
cross sections are presented as a function of the longitudinal fraction of the
proton momentum carried by the leading neutron, xL, and of its transverse
momentum squared, pT^2. The dijet data are compared to inclusive DIS and
photoproduction results; they are all consistent with a simple pion-exchange
model. The neutron yield as a function of xL was found to depend only on the
fraction of the proton beam energy going into the forward region, independent
of the hard process. No firm conclusion can be drawn on the presence of
rescattering effects.Comment: 40 pages, 18 figure
Search for leptophobic Z ' bosons decaying into four-lepton final states in proton-proton collisions at root s=8 TeV
Peer reviewe
Search for black holes and other new phenomena in high-multiplicity final states in proton-proton collisions at root s=13 TeV
Peer reviewe
- …