Model investigation of inlet plenum flow straightening techniques for altitude test facility

An investigation was conducted to evaluate and improve the quality of the airflow to be supplied to the engine in altitude test chambers 3 and 4 of the Propulsion Systems Laboratory at the Lewis Research Center. One-twentieth-scale models of the inlet plenum chamber of the two test chambers were used in the investigation to minimize time and cost. It was possible to reduce the velocity spread in the inlet plenum from approximately 100 m/sec (330 ft/sec) to approximately 10 m/sec (30 ft/sec) through the combined use of flow diverters, multiple spaced screens, flow straighteners, and turning vanes

Mesoscopic Thermovoltage Measurement Design

Quantitative thermoelectric measurements in the mesoscopic regime require accurate knowledge of temperature, thermovoltage, and device energy scales. We consider the effect of a finite load resistance on thermovoltage measurements of InAs/InP heterostructure nanowires. Load resistance and ac attenuation distort the measured thermovoltage therefore complicating the evaluation of device performance. Understanding these effects improves experimental design and data interpretation.Comment: 2 pages, 3 figure

Increasing thermoelectric performance using coherent transport

We show that coherent electron transport through zero-dimensional systems can be used to tailor the shape of the system's transmission function. This quantum-engineering approach can be used to enhance the performance of quantum dots or molecules in thermal-to-electric power conversion. Specifically, we show that electron interference in a two-level system can substantially improve the maximum thermoelectric power and the efficiency at maximum power by suppressing parasitic charge flow near the Fermi energy, and by reducing electronic heat conduction. We discuss possible realizations of this approach in molecular junctions or quantum dots.Comment: 4+ pages, 4 figure

Assessment of mechanical properties and microstructure characterizing techniques in their ability to quantify amount of cold work in 316l alloy

Stress corrosion cracking (SCC) behavior is a matter of concern for structural materials, namely, stainless steels and nickel alloys, in nuclear power plants. High levels of cold work (CW) have shown to both reduce crack initiation times and increase crack growth rates. Cold working has numerous effects on a material, including changes in microstructure, mechanical properties, and residual stress state, yet it is typically reported as a simple percent change in geometry. There is need to develop a strategy for quantitative assessment of cold-work level in order to better understand stress corrosion cracking test data. Five assessment techniques, commonly performed alongside stress corrosion cracking testing (optical microscopy (OM), electron backscatter diffraction (EBSD), X-ray diffraction (XRD), tensile testing, and hardness testing) are evaluated with respect to their ability to quantify the level of CW in a component. The test material is stainless steel 316L that has been cold-rolled to three conditions: 0%, 20%, and 30% CW. Measurement results for each assessment method include correlation with CW condition and repeatability data. Measured values showed significant spatial variation, illustrating that CW level is not uniform throughout a component. Mechanical properties (tensile testing, hardness) were found to correlate most linearly with the amount of imparted CW

Experimental verification of reciprocity relations in quantum thermoelectric transport

Symmetry relations are manifestations of fundamental principles and constitute cornerstones of modern physics. An example are the Onsager relations between coefficients connecting thermodynamic fluxes and forces, central to transport theory and experiments. Initially formulated for classical systems, these reciprocity relations are also fulfilled in quantum conductors. Surprisingly, novel relations have been predicted specifically for thermoelectric transport. However, whereas these thermoelectric reciprocity relations have to date not been verified, they have been predicted to be sensitive to inelastic scattering, always present at finite temperature. The question whether the relations exist in practice is important for thermoelectricity: whereas their existence may simplify the theory of complex thermoelectric materials, their absence has been shown to enable, in principle, higher thermoelectric energy conversion efficiency for a given material quality. Here we experimentally verify the thermoelectric reciprocity relations in a four-terminal mesoscopic device where each terminal can be electrically and thermally biased, individually. The linear response thermoelectric coefficients are found to be symmetric under simultaneous reversal of magnetic field and exchange of injection and emission contacts. Intriguingly, we also observe the breakdown of the reciprocity relations as a function of increasing thermal bias. Our measurements thus clearly establish the existence of the thermoelectric reciprocity relations, as well as the possibility to control their breakdown with the potential to enhance thermoelectric performanceComment: 7 pages, 5 figure

Threshold feedback control for a collective flashing ratchet: threshold dependence

We study the threshold control protocol for a collective flashing ratchet. In particular, we analyze the dependence of the current on the values of the thresholds. We have found analytical expressions for the small threshold dependence both for the few and for the many particle case. For few particles the current is a decreasing function of the thresholds, thus, the maximum current is reached for zero thresholds. In contrast, for many particles the optimal thresholds have a nonzero finite value. We have numerically checked the relation that allows to obtain the optimal thresholds for an infinite number of particles from the optimal period of the periodic protocol. These optimal thresholds for an infinite number of particles give good results for many particles. In addition, they also give good results for few particles due to the smooth dependence of the current up to these threshold values.Comment: LaTeX, 10 pages, 7 figures, improved version to appear in Phys. Rev.

Diffusion Enhancement in a Periodic Potential under High-Frequency Space-Dependent Forcing

We study the long-time behavior of underdamped Brownian particle moving through a viscous medium and in a systematic potential, when it is subjected to a space-dependent high-frequency periodic force. When the frequency is very large, much larger than all other relevant system-frequencies, there is a Kapitsa time-window wherein the effect of frequency dependent forcing can be replaced by a static effective potential. Our new analysis includes the case when the forcing, in addition to being frequency-dependent, is space-dependent as well. The results of the Kapitsa analysis then lead to additional contributions to the effective potential. These are applied to the numerical calculation of the diffusion coefficient (D) for a Brownian particle moving in a periodic potential. Presented are numerical results, which are in excellent agreement with theoretical predictions and which indicate a significant enhancement of D due to the space-dependent forcing terms. In addition we study the transport property (current) of underdamped Brownian particles in a ratchet potential.Comment: RevTex 6 pages, 5 figure

Effect of time delay on feedback control of a flashing ratchet

It was recently shown that the use of feedback control can improve the performance of a flashing ratchet. We investigate the effect of a time delay in the implementation of feedback control in a closed-loop collective flashing ratchet, using Langevin dynamics simulations. Surprisingly, for a large ensemble, a well-chosen delay time improves the ratchet performance by allowing the system to synchronize into a quasi-periodic stable mode of oscillation that reproduces the optimal average velocity for a periodically flashing ratchet. For a small ensemble, on the other hand, finite delay times significantly reduce the benefit of feedback control for the time-averaged velocity, because the relevance of information decays on a time scale set by the diffusion time of the particles. Based on these results, we establish that experimental use of feedback control is realistic.Comment: 6 pages, 6 figures, to appear in Europhysics Letter

Quantum-dot thermometry

We present a method for the measurement of a temperature differential across a single quantum dot that has transmission resonances that are separated in energy by much more than the thermal energy. We determine numerically that the method is accurate to within a few percent across a wide range of parameters. The proposed method measures the temperature of the electrons that enter the quantum dot and will be useful in experiments that aim to test theory which predicts quantum dots are highly-efficient thermoelectrics.Comment: 3 pages, 4 Figure