118 research outputs found
Phosphorus Release Characteristics from Biosolids-Derived Organomineral Fertilizers
This study investigated the availability of phosphorus (P) following soil application of a novel biosolids-derived organomineral fertilizer (OMF15; 15:4:4) in comparison with single superphosphate (0:18:0). Two soil types of contrasting characteristics were incubated over a period of 90 days at 25 °C and maintained near field capacity. Phosphorus was applied at rates equivalent to 0 (control), 150, and 300 kg haâ1 of P2O5, respectively. Availability of P from OMF15 was low throughout the experiment accounting for less than 6.5% of total OMF15-P applied. It was shown that after the 90 days incubation period, the overall increase in soil extractable P in OMF15-treated soil was marginal in both soil types. For single superphosphate (SSP), P availability ranged from 16% to 46% of total SSP-P applied. Application of SSP increased soil extractable P levels significantly (P < 0.001) compared with unfertilized control soils. The results of this study aided the development of fertilization strategies for the best use of OMF produced from nutrient-enriched biosolids granules for applications in winter cereal and grass crops in England
Nitrogen release characteristics from biosolids-derived organomineral fertilizers
is study investigated the availability of nitrogen (N) following soil application of a novel biosolids-derived organomineral fertilizer (OMF15â15:4:4) in comparison with urea (46% N). OMF15 is produced by coating biosolids granules (particle size range: 1.10â5.50 mm in diameter) with urea and potash [60% potassium oxide (K2O)], which increase the concentration of mineral N and potassium (K), respectively, resulting in a balanced fertilizer material suitable for application in cereal and grass crops. The study comprised two soil types of contrasting characteristics which were incubated over a period of 90 days at 25 °C and maintained near field capacity. Nitrogen was applied at rates equivalent to 0 (control), 150, and 300 kg haâ1, and soil mineral N measured routinely using standard laboratory techniques. Results showed that the majority of N was released from OMF15 within 30 days from application (range: 40% to 72% of total OMF15-N applied) with a further 10% to 28% in the following 60â90 days. OMF15 required an accumulated thermal time of 2250 degrees-day to release between 68% and 79% of the total OMF15-N applied. From this, it was inferred that mineralization of the organic-N fraction in OMF15 is likely to progress beyond harvest of winter cereal crops in-field conditions in England. The results of this study aided the development of fertilization strategies for the best use of OMF in winter cereal and grass crops
An investigation into the fertilizer particle dynamics off-the-disc
The particle size range specifications for two biosolids-derived organomineral fertilizers (OMF) known as OMF10 (10:4:4) and OMF15 (15:4:4) were established. Such specifications will enable field application of OMF with spinning disc systems using conventional tramlines spacing. A theoretical model was developed, which predicts the trajectory of individual fertilizer particles off-the-disc. The drag coefficient (Cd) was estimated for small time steps (10-6 s) in the trajectory of the particle as a function of the Reynolds number. For the range of initial velocities (20 to 40 m s-1), release angles (0Ă° to 10Ă°) and particle densities (1000 to 2000 kg m-3) investigated, the analysis showed that OMF10 and OMF15 need to have particle diameters between 1.10 and 5.80 mm, and between 1.05 and 5.50 mm, respectively, to provide similar spreading performance to urea with particle size range of 1.00 to 5.25 mm in diameter. OMF10 and OMF15 should have 80% (by weight) of particles between 2.65 and 4.30 mm, and between 2.55 and 4.10 mm, respectively. Due to the physical properties of the material, disc designs and settings that enable working at a specified bout width by providing a small upward particle trajectory angle (e.g., 10Ă°) are preferred to high rotational velocities. However, field application of OMF with spinning discs applicators may be restricted to tramlines spaced at a maximum of 24 m; particularly, when some degree of overlapping is required between two adjacent bouts. The performance of granular fertilizers can be predicted based on properties of the material, such as particle density and size range, using the contour plots developed in this study
Understanding the JD7760 round module picker impacts
This paper communicates further the findings, pertaining to the John Deere 7760 (JD7760) round module picker, of the Cotton Growing Practices 2013 industry survey and current research at the National Centre for Engineering in Agriculture. The grower data is used to highlight decision making processes used and provides insight into potentially latent impacts on system components, particularly the land resource. Adoption drivers and considerations are discussed
against machine potential, the Australian picker market and
the potential for soil compaction is demonstrated to contrast
considerations
Characterisation of organomineral fertilisers derived from nutrient-enriched biosolids granules
Organomineral fertilisers (OMFs) were produced by coating biosolids granules with urea and potash. Two OMF formulations with Nâ:âP2O5â:âK2O compositions: 10â:â4â:â4 (OMF10) and 15â:â4â:â4 (OMF15) were developed for application in grassland and arable crops. Routine fertiliser analyses were conducted on four batches of OMF and biosolids granules and compared with a sample of urea to determine key physical and chemical properties of the materials which affect handling and spreading, soil behaviour, and fertiliser value. Bulk and particle densities were in the range of 608 to 618âkgâmâ3, and 1297 to 1357âkgâmâ3, respectively. Compression tests showed that OMF particles undergo deformation followed by multiple failures without disintegration of the granules when vertical load was applied. Static particle strength was between 1.18 and 4.33âNâmmâ2 depending on the particle diameter. The use of a model for fertiliser particle distribution studies showed that OMF granules should be between 1.10 and 5.50âmm in diameter with about 80% of the particles in the range of 2.25 to 4.40âmm to enable application at 18âm tramline spacing. This research utilises novel technology to improve the fertiliser value of biosolids, reduce disposal costs, and deliver a range of environmental benefits associated with recycling
Field-scale evaluation of biosolids-derived organomineral fertilizers applied to winter wheat in England
Field-scale experiments in four crop seasons established the agronomic performance of biosolids-derived organomineral fertilizers (OMF) for winter wheat (Triticum aestivum L.) production in England. Two OMF formulations (OMF10 10:4:4 and OMF15 15:4:4) were compared with urea and biosolids granules (â5:6:0.2) to determine crop responses and fertilizer effects on soil chemical properties. Fertilizers were applied at N rates between 0 and 250 kg haâ1 at regular increments of 50 kg haâ1 N. Average grain yields with OMF10 and OMF15 were higher than with biosolids granules, but lower than with urea (P < 0.05). The optimum N application rates, and corresponding grain yields, were 245 and 7900 kg haâ1 for biosolids, 257 and 9100 kg haâ1 for OMF10, 249 and 9500 kg haâ1 for OMF15, and 225 and 10350 kg haâ1 for urea, respectively. Differences in grain yield between fertilizer treatments were explained by differences in yield components, particularly number of grains and thousand-grain-weight. Grain-N recoveries were 31% for biosolids, â40% for OMF, and 52% for urea. Organomineral fertilizers-induced changes in soil extractable P and soil P Index were not significant. Thus, application of OMF replenished P offtake by the crop and therefore supported the choice of the proposed OMF formulations. By contrast, extractable P increased in biosolids and decreased in urea-treated soils, respectively. Heavy metals in soil were unaffected by fertilizer treatment and lower than permissible limit values. The use of OMF for winter wheat production appears to be a sustainable approach to recycling biosolids to land
Formulation, utilisation and evaluation of organomineral fertilisers
The water industry recognises significant cost advantages in recycling sewage sludge (biosolids) to agricultural land compared with alternative more expensive disposal options such as incineration or landfill. A recent technique was proposed by United Utilities plc for the production of organomineral fertilisers (OMF) from biosolids granules which adds additional nitrogen to the biosolidsâ nutrients to form a balanced NPK fertiliser. The aim of this research was to determine the effects in cereal and grass crops of using organomineral fertilisers (OMF) made from nutrients-enriched biosolids granules and to contribute towards the understanding of nutrient management and dynamics in agricultural systems. The research included soil incubation, glasshouse, lysimeters and field studies which used winter wheat (Triticum aestivum L.) and ryegrass (Lolium perenne L.). A theoretical model was developed for fertiliser particle distribution studies which required the determination of key physical properties of the products. Two OMF formulations have been suggested: OMF10 and OMF15 which have the following NPK compositions: 10:4:4 and 15:4:4 respectively. These were suggested for use in grassland as well as arable cropping. The particle trajectory model showed that the particle size range for OMF10 and OMF15 should be between 1.10 and 5.50 mm and between 1.05 and 5.30 mm in diameter respectively. Cont/d.EThOS - Electronic Theses Online ServiceGBUnited Kingdo
Field-scale evaluation of biosolids-derived organomineral fertilisers applied to ryegrass (Lolium perenne L.) in England
A field-scale experiment was conducted to compare the suitability of two organomineral fertiliser (OMF) formulations (OMF- 10: 4: 4 and OMF- 15: 4: 4) with urea and biosolids granules applied to perennial ryegrass. Results showed a 25% to 30% increase in dry matter yield (DMY) with application of OMF compared with biosolids granules but about 5% lower than urea. For OMF, an average input of 0.8 Ă N max yielded 0.98 Ă DMY max which was similar to that of urea; whereas, for biosolids, a yield of 0.92 Ă DMY max required an input of 0.6 Ă N max but DMY was lower (P 0.05), in soil extractable P. The application of OMF at rates which do not exceed the optimum N rate for the grass crop should not induce significant changes in soil P Index including application to soils with satisfactory P levels. OMF application strategies are discussed which will enable minimising environmental concerns and maximising fertiliser use efficiency
Recommended from our members
In vitro pre-vascularisation of tissue-engineered constructs A co-culture perspective
In vitro pre-vascularization is one of the main vascularization strategies in the tissue engineering field. Culturing cells within a tissue-engineered construct (TEC) prior to implantation provides researchers with a greater degree of control over the fate of the cells. However, balancing the diverse range of different cell culture parameters in vitro is seldom easy and in most cases, especially in highly vascularized tissues, more than one cell type will reside within the cell culture system. Culturing multiple cell types in the same construct presents its own unique challenges and pitfalls. The following review examines endothelial-driven vascularization and evaluates the direct and indirect role other cell types have in vessel and capillary formation. The article then analyses the different parameters researchers can modulate in a co-culture system in order to design optimal tissue-engineered constructs to match desired clinical applications
- âŠ