The formation of ultrafine grained steel microstructures through thermomechanical processing.

The formation of ultrafine grained steels is an area of intense research around the World. There are a number of methods to produce grain sizes of approximately 1 &micro;m, ranging from extreme thermal and deformation cycles to more typical thermomechanical processes. This paper reviews the status of the production of ultrafine grained steels through relatively simple thermomechanical processing. It is shown that this requires deformation within the Ae3 to Ar3 temperature range for a given alloy. The formation of ultrafine ferrite involves a dynamic transformation of a significant volume fraction of the austenite to ferrite. This dynamic strain induced transformation arises from the introduction of additional intragranular nucleation sites. It is possible that the deformation also hinders the growth or coarsening of the ferrite and may also lead to dynamic recrystallization of the ferrite. The most likely commercial exploitation of ultrafine ferrite would appear to rely on the formation of a critical volume fraction of dynamic strain induced ferrite followed by controlled cooling to ensure this is maintained to room temperature and to also form other secondary phases, such as martensite, bainite and/or retained austenite to improve the formability.<br /

Crystallographic analysis of nano-structured bainitic steels

A 0.79C-1.5Si-1.98Mn-0.98Cr-0.24Mo-1.06Al-1.58Co (wt%) steel was isothermally heat treated at 200 and 350&deg;C bainitic transformation temperatures. The microstructure was consisted of bainitic ferrite lath and retained austenite for both heat treatment conditions. The crystallographic analysis revealed that the bainitic ferrite laths are close to the Nishiyama-Wassermann orientation relationship with their parent austenite. The isothermal bainite transformation temperature has a significant effect on the retained austenite characteristics and the variant selection of the bainitic ferrite laths. In general, a decrease in the isothennal bainite transformation temperature refined the bainitic structure and weakened the variant selection.<br /

Effect of composition and processing parameters on the formation of nano-bainite in advanced high strength steels

The nano-bainitic microstructures were compared in a 0.79C-1.5Si-1.98Mn-0.24Mo-1.06Al (wt%) steel after isothermal heat-treatment and a Fe-0.2C-1.5Mn-1.2Si-0.3M0-0.6Al-0.02Nb (wt%) steel after controlled thermo-mechanical processing. The microstructure for both steels consisted of bainite. The microstructural characteristics of bainite, such as the morphology of the nano-bainite and thicknesses of bainitic ferrite and retained austenite layers, as a function of steel composition and processing was studied using transmission electron microscopy (TEM). It was found that the nano-bainitic structure can be formed in the low alloy steel through thermomechanical processing. Atom probe tomography (APT) was employed as a powerful technique to determine local composition distributions in three dimensions with atomic resolution. The important conclusions from the APT research were that the carbon content of bainitic ferrite is higher than expected from paraequilibrium level of carbon in ferrite for both steels and that Fe-C clusters and fine particles are formed in the bainitic ferrite in both steels despite the high level of Si

Formation of ultrafine grained microstructures in steel through strain induced transformation during single pass hot rolling

In the present study, wedge-shape samples were used to study the effect of strain induced transformation on the formation of ultrafine grained structures in steel by single pass rolling. The results showed two different transition strains for bainite formation and ultrafine ferrite (UFF) formation in the surface layer of strip at reductions of 40% and 70%, respectively, in a plain carbon steel. The bainitic microstructure formed by strain induced bainitic transformation during single pass rolling was also very fine. The evolution of UFF formation in the surface layer showed that ferrite coarsening is significantly reduced through strain induced transformation combined with rapid cooling in comparison with the centre of the strip. In the surface, the ferrite coarsening mostly occurred for intragranular nucleated grains (IG) rather than grain boundary (GB) ferrite grains. The results suggest that normal grain growth occurred during overall transformation in the GB ferrite grains. In the centre of the strip, there was significantly more coarsening of ferrite grains nucleated on the prior austenite grain boundaries.<br /

The influence of solute carbon in cold-rolled steels on shear band formation and recrystallization texture

Two experiments were conducted to clarify the roles of grain size, solute carbon and strain in determining the recrystallization textures of cold-rolled and annealed steels. In the first experiment, samples of coarse-grained low-carbon (LC) and interstitial-free (IF) steels were cold-rolled to a 75% reduction in thickness. One sample from each steel was polished and cold-rolled an additional 5%, while the remaining samples were annealed for various times at 650&deg;C. In the second experiment, three samples from a commercial LC steel sheet were rolled 70% at 300&deg;C. Two of the samples were given a further rolling reduction of 5% of the original thickness, with one of the samples being given this additional reduction at 300&deg;C and the other at room temperature. Goss recrystallization textures are strengthened by coarse initial grain sizes, the presence of solute carbon and rolling at a temperature where dynamic strain ageing occurs, but are weakened by additional rolling beyond a reduction of 70%, especially when this extra rolling is conducted at a temperature where dynamic strain ageing does not occur. Characterization of key features of the deformed and recrystallized steels using optical microscopy, scanning electron microscopy (SEM) and electron back-scatter diffraction (EBSD) supports a rationale for these effects based on the repeated activation and deactivation of shear bands and the influence of solute carbon and dynamic strain ageing on the operating life of the bands and the accumulation of strain within them

New Insight into Toughness Enhancement in a Lath Martensitic Steel

Grain refinement of the parent austenite led to a significant change in the intervariant boundary network of martensite, ultimately improving the mechanical properties (i.e., toughness and hardness). Molecular dynamics simulation demonstrated that the propensity for crack propagation was largely governed by the intervariant boundary energy, where the crack propagation rate was much faster for the high-energy 60 deg/[110] twist boundary than the low-energy 60 deg/[111] symmetric tilt boundary. This agreed with experimental observations where parent austenite grain refinement increased the low-energy boundary population at the expense of high-energy intervariant boundaries in martensite. In turn, this led to a significant toughness improvement without sacrificing the strength. This finding demonstrates that the mechanical properties of a martensitic microstructure can be significantly improved through intervariant boundary network engineering.publishedVersio

The influence of parent austenite characteristics on the intervariant boundary network in a lath martensitic steel

The influence of the parent austenite deformation state on the intervariant boundary network (i.e., population, plane orientation, and connectivity) of a lath martensitic microstructure was investigated using conventional EBSD mapping and five-parameter boundary analysis approach along with quantification of boundary connectivity using homology metrics. The lath martensite largely revealed a bimodal misorientation angle distribution, closely matched with the Kurdjumov–Sachs (K–S) orientation relationship. The application of deformation significantly changed the distribution, gradually reducing the intensity of the 60° misorientation angle peak. This was largely ascribed to substructure development within the parent austenite upon deformation, which stimulates particular variant/s having a habit plane (011)α′ closely parallel to the primary (111)γ and/or secondary (11¯¯¯1)γ slip plane. The interaction of these variants eventually promoted specific intervariant boundaries (e.g., 60°/[111], 10.5°/[011], and 49.5°/[110]) at the expense of 60°/[011]. The application of deformation in the parent austenite did not change the intervariant boundary plane character distribution, which mostly exhibited an anisotropic character terminated on {110} planes because of the displacive nature of the martensitic transformation. However, the extent of anisotropy progressively decreased with increasing strain in the austenite prior to transformation. The grain boundary network connectivity was markedly altered due to the local variant selection induced by the deformation. Deformation in the austenite regime generally decreased the connectivity of boundaries having a {110} plane orientation. The intervariant boundaries with the {110} twist character also displayed a similar trend, though the connectivity of {110} tilt boundaries progressively enhanced with increasing strain. The former was closely matched with a decrease in the population of 60°/[110] intervariant boundaries with the strain. The current findings suggest that the intervariant boundary network of lath martensite can be manipulated through changes in the parent austenite deformation state which, in turn, can be used to enhance key final product properties such as toughness.publishedVersio

The nitrocarburising response of low temperature bainite steel

The nitrocarburising response of low transformation temperature ultrafine and nanoscale bainitic steel was investigated and compared with martensite and pearlite from the same steel composition. It was found that the retained austenite content of the bainitic steel dictated the core hardness after nitrocarburising. The refined bainitic structure showed improvements in the nitriding depth and hardness of the nitrocarburised layer, compared to coarser grained martensitic and pearlitic structures, possibly due to the fine structure and the distribution of nitride forming elements

The role of parent austenite grain size on the variant selection and intervariant boundary network in a lath martensitic steel

This study investigated the influence of parent austenite grain refinement on the intervariant boundary network (population and connectivity) in a lath martensitic steel. Parent austenite grain refinement revealed a progressive reduction in the fraction of the 60° misorientation boundaries in martensite, which was linked to a decrease in the 60° / [110] intervariant boundary population. The phenomenological theory of martensite crystallography demonstrated that the variant selection mechanism altered from the 3-variant clustering (V1V3V5) in the coarse parent austenite towards the 4-variant clustering (V1V2V3V4) in the fine parent austenite grain, due to the change in the lattice parameter of the parent and daughter phase in which the martensite transformation occurs, as measured using in situ neutron diffraction. The change in the variant clustering arrangement with the parent austenite grain refinement led to a progressive promotion of 60° / [111] and 10.5° / [011] intervariant boundaries at the expense of 60° / [110] martensite intervariant boundaries. Subsequently, the connectivity of low energy {110} tilt intervariant boundaries gradually increased through the refinement of parent austenite grain size, eventually reducing the high energy {110} twist boundary connectivity. This change improved the impact toughness of martensite produced from the fine-grained austenite as the weak connectivity of high energy boundaries delays the coalescence of voids, promoting ductile fracture.publishedVersio

The effect of multiple deformations on the formation of ultrafine grained steels

A C-Mn-Nb-Ti steel was deformed by hot torsion to study ultrafine ferrite formation through dynamic strain-induced transformation (DSIT) in conjunction with air cooling. A systematic study was carried out first to evaluate the effect of deformation temperature and prior austenite grain size on the critical strain for ultrafine ferrite formation (&epsilon; C,UFF) through single-pass deformation. Then, multiple deformations in the nonrecrystallization region were used to study the effect of thermomechanical parameters (i.e., strain, deformation temperature, etc.) on &epsilon; C,UFF. The multiple deformations in the nonrecrystallization region significantly reduced &epsilon; C,UFF, although the total equivalent strain for a given thermomechanical condition was higher than that required in single-pass deformation. The current study on a Ni-30Fe austenitic model alloy revealed that laminar microband structures were the key intragranular defects in the austenite for nucleation of ferrite during the hot torsion test. The microbands were refined and overall misorientation angle distribution increased with a decrease in the deformation temperature for a given thermomechanical processing condition. For nonisothermal multipass deformation, there was some contribution to the formation of high-angle microband boundaries from strains at higher temperature, although the strains were not completely additive.<br /