6,990 research outputs found
Low-speed wind tunnel investigation of the lateral-directional characterisitcs of a large-scale variable wing-sweep fighter model in the high-lift configuration
The low-speed characteristics of a large-scale model of the F-14A aircraft were studied in tests conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel. The primary purpose of the present tests was the determination of lateral-directional stability levels and control effectiveness of the aircraft in its high-lift configuration. Tests were conducted at wing angles of attack between minus 2 deg and 30 deg and with sideslip angles between minus 12 deg and 12 deg. Data were taken at a Reynolds number of 8.0 million based on a wing mean aerodynamic chord of 2.24 m (7.36 ft). The model configuration was changed as required to show the effects of direct lift control (spoilers) at yaw, yaw angle with speed brake deflected, and various amounts and combinations of roll control
Development of microwave NDT inspection techniques for large solid propellant rocket motors Final report
Microwave nondestructive testing techniques for large solid propellant rocket engine
Recommended from our members
Towards a change process planning tool
The relationship between a product and its design process is generally complex and not fully understood. When modifying a product, industry still rarely considers the implementation process and its consequences for other design activities in the company, which is hard to assess with conventional planning methods. Although change processes are highly constrained, product and process constraints are not usually considered together or traded off against each other when planning the change. Inadequate assessment and planning of the change implementation process can lead to costly knock-on effects across the product and the design process. This paper argues for a combination of change and process research and discusses requirements for a change process planning tool. It proposes a system for the analysis of the impact of change on the product as well as other company activities. Then, a more informed selection between change alternatives is possible
Recommended from our members
Parameter trails
Successful communication is vital for the success of any design project. However, communication often fails, adversely affecting design process efficiency and product quality.understand the connections between different aspects of design and don–t know where to find out more information or who to talk to. This paper presents a new model, developed from current project planning techniques, which supports communication using parameter-specific data. It enables designers to question information, inform their colleagues pro-actively and assess the impact of changing parameter values on subsequent design tasks. Such interaction is critical in allowing designers to see how their own tasks fit into the overall product design
Aerodynamic design guidelines and computer program for estimation of subsonic wind tunnel performance
General guidelines are given for the design of diffusers, contractions, corners, and the inlets and exits of non-return tunnels. A system of equations, reflecting the current technology, has been compiled and assembled into a computer program (a user's manual for this program is included) for determining the total pressure losses. The formulation presented is applicable to compressible flow through most closed- or open-throat, single-, double-, or non-return wind tunnels. A comparison of estimated performance with that actually achieved by several existing facilities produced generally good agreement
A functional analysis of change propagation
A thorough understanding of change propagation is fundamental to effective change management during product redesign. A new model of change propagation, as a result of the interaction of form and function is presented and used to develop an analysis method that determines how change is likely to propagate. The analysis produces a Design Structure Matrix, which clearly illustrates change propagation paths and highlights connections that could otherwise be ignored. This provides the user with an in-depth knowledge of product connectivity, which has the potential to support the design process and reduce the product's susceptibility to future change
Environmental legislation as a driver of design
and other research output
Wind sensitivity studies of a non-return wind tunnel with a 216- by 432-mm (8.5- by 17.0-inches) test section, phase 2
The refinement of inlet and exit treatments were studied which would minimize the effect of external wind on the test-section flow quality of a nonreturn wind tunnel. The investigation was conducted in the Ames Research Center 40- by 80-foot Wind Tunnel which served as the wind source. Several inlets and two exits were tested at wind directions ranging from 0 to 180 degrees and at wind-to-test-section velocity ratios from zero to somewhat greater than one. For the best inlet configuration the flow quality was good, with a velocity deviation in each of the three component directions generally less. The loss in total pressure due to the inlet treatment was low: about 0.035 of the test-section dynamic pressure for the no-wind case
An aerodynamic investigation of two 1.83-meter-diameter fan systems designed to drive a subsonic wind tunnel
An experimental, aerodynamic investigation was made of two 1.83 m diameter fan systems which are being considered for the repowered drive section of the 40- by 80-foot wind tunnel at NASA Ames Research Center. One system was low speed, the other was high speed. The low speed fan was tested at various stagger angles from 32.9 deg to 62.9 deg. At a fan blade stagger angle of 40.8 deg and operating at a tip speed of 1155 m/sec, the low speed fan developed 207.3 m of head. The high speed fan had a design blade stagger angle of 56.2 deg and was tested at this stagger angle only. The high speed fan operating at 191.5 m/sec developed 207.3 m of head. Radial distributions of static pressure coefficients, total pressure coefficients, and angles of swirl are presented. Radial surveys were conducted at four azimuth locations in front of the fan, and repeated downstream of the fan. Data were taken for various flow control devices and for two inlet contraction lengths
- …