Report on ITER Emergency Task Fatigue studies of S65c beryllium

SIGLEAvailable from British Library Document Supply Centre- DSC:4672.2625(JET-R--94/04) / BLDSC - British Library Document Supply CentreGBUnited Kingdo

High performance Joint European Torus (JET) plasmas for deuterium-tritium operation with the MkII divertor

Planned experiments in the Joint European Torus [Plasma Physics and Controlled Fusion Research, Proceedings, 13th International Conference, Washington, D.C., 1990 (International Atomic Energy Agency, Vienna, 1991), Vol. 1, p. 27] (JET) with deuterium-tritium (D-T) plasmas require high fusion performance for alpha-particle heating studies and for investigation of isotope dependence in conditions relevant to the International Thermonuclear Experimental Reactor [Plasma Phys. Controlled Fusion 37, A19 (1995)]. In deuterium plasmas, the highest neutron rates have been obtained in the hot-ion high-confinement mode (H mode) which is ultimately limited by magnetohydrodynamic (MHD) phenomena when the pressure gradient approaches ideal ballooning and kink stability limits in the vicinity of the edge transport barrier. Results are reported confirming the MkII divertor's increased closure and pumping in this regime, progress in understanding the MHD-related termination is discussed, and the use of ion cyclotron resonance heating (ICRH) in combination with high-power neutral beams to increase the neutron yield is described. In separate experiments internal transport barriers have been established through careful programming of the current ramp and heating waveforms, and neutron emission comparable with the best hot-ion II-modes achieved. Steady-state II-mode discharges exhibiting edge localized modes (ELMs) in reactor-like configurations and conditions have been demonstrated, including cases in which relevant dimensionless parameter values are preserved, ready also for testing in D-T. (C) 1997 American institute of Physics

JET results with the new pumped divertor and implications for ITER

This paper presents an overview of results of the 1994/95 experimental campaign on JET with the new pumped divertor and draws implications for ITER in the areas of detached and radiative divertor plasmas, the use of beryllium as a divertor target the material, the confinement properties of discharges with the same dimensionless parameters (except for the dimensionless Larmor radius) as ITER and the effect of varying the toroidal magnetic field ripple in the ITER relevant range. Discharges with high fusion performance at high current, in steady-state with ELMs and in the ELM-free hot-ion H-mode, are also reported. Limits to operations are discussed and projections to D-T performance are made

Fusion Energy-Production from a Deuterium-Tritium Plasma in the Jet Tokamak

The paper describes a series of experiments in the Joint European Torus (JET), culminating in the first tokamak discharges in deuterium-tritium fuelled mixtures. The experiments were undertaken within limits imposed by restrictions on vessel activation and tritium usage. The objectives were: (i) to produce more than one megawatt of fusion power in a controlled way; (ii) to validate transport codes and provide a basis for accurately predicting the performance of deuterium-tritium plasma from measurements made in deuterium plasmas; (iii) to determine tritium retention in the torus systems and to establish the effectiveness of discharge cleaning techniques for tritium removal; (iv) to demonstrate the technology related to tritium usage; and (v) to establish safe procedures for handling tritium in compliance with the regulatory requirements. A single-null X-point magnetic configuration, diverted onto the upper carbon target, with reversed toroidal magnetic field was chosen. Deuterium plasmas were heated by high power, long duration deuterium neutral beams from fourteen sources and fuelled also by up to two neutral beam sources injecting tritium. The results from three of these high performance hot ion H-mode discharges are described: a high performance pure deuterium discharge; a deuterium-tritium discharge with a 1% mixture of tritium fed to one neutral beam source; and a deuterium-tritium discharge with 100% tritium fed to two neutral beam sources. The TRANSP code was used to check the internal consistency of the measured data and to determine the origin of the measured neutron fluxes. In the best deuterium-tritium discharge, the tritium concentration was about 11% at the time of peak performance, when the total neutron emission rate was 6.0 x 10(17) neutrons/s. The integrated total neutron yield over the high power phase, which lasted about 2 s, was 7.2 x 10(17) neutrons, with an accuracy of +/- 7%. The actual fusion amplification factor, Q(DT), was about 0.15. With an optimum tritium concentration, this pulse would have produced a fusion power of almost-equal-to 5 MW and a nominal Q(DT) almost-equal-to 0.46. The same extrapolation for the pure deuterium discharge would have given almost-equal-to 11 MW and a nominal Q(DT) = 1.14, so that the total fusion power (neutrons and alpha-particles) would have exceeded the total losses in the equivalent deuterium-tritium discharge in these transient conditions. Techniques for introducing, tracking, monitoring and recovering tritium were demonstrated to be highly effective: essentially all of the tritium introduced into the neutral beam system and, so far, about two thirds of that introduced into the torus have been recovered