Espirais e Hélices - Do Polímero mais abundante da natureza

A celulose é o polímero renovável mais abundante do mundo. É o principal constituinte das paredes celulares das plantas, as quais constituem a sua principal fonte

Experimental calibration of the bond-slip relationship of different CFRP-to-timber joints through digital image correlation measurements

UIDB/EMS/00667/2020Nowadays, the use of the Digital Image Correlation (DIC) technique has spread and it is being used in several engineering areas to measure displacements. The available data obtained from the DIC measurement to evaluate the bond performance between a Carbon fibre Reinforced Polymer (CFRP) externally bonded to a timber substrate is scarce. From the existing data obtained with other materials, this contactless technique revealed to be quite useful but its accuracy with other well-established techniques, such as the use of electric strain gauges is not well understood yet. Therefore, the current work aims to study the accuracy of 2D DIC measurements with the measurements obtained from the use of strain gauges within a low-cost perspective. To that end, several CFRP-to-timber bonded joints were tested under the single-lap shear test and different bonding techniques were considered as well. Some flaws intrinsically derived from the DIC measurements that complicate the bond assessment, such as the fluctuations in the generated displacements field, are identified, and to bypass this problem a new methodology is proposed. This new methodology is based on two different closed-form solutions that, after defining the local and global bond behaviours of different CFRP-to-timber bonded joints, allowed to eliminate the fluctuations found from the DIC measurements, facilitating the estimation and the comprehension of the full debonding process of the CFRP-to-timber joints, which was achieved with a good proximity to the homologous debonding process derived from the strain gauge measurements.publishersversionpublishe

Host effect on morphology of the fruit fly Anastrepha zenildae (Diptera: Tephritidae) from the Semi‑Arid region of Rio Grande do Norte

Anastrepha zenildae Zucchi is an important pest in the Semi-Arid region of Rio Grande do Norte and other states in Brazil, with Guava being its main host. Environment induced morphological changes in adult fruit flies can lead to mating incompatibilities among populations within a species. Furthermore, sexual isolation between these populations can be one of the first steps in the speciation process, as described to other tephritid fly species. Here, we compared several body measurements through analysis of variance and geometric morphometrics to assess significant morphological differences between sympatric flies from different hosts: Guava and Jua. We found significant differences in body size for both sexes of flies from the different fruit hosts, with flies from Guava being the larger. Different degrees of sexual size dimorphism of flies from each fruit has also been detected. Flies from different fruits also exhibited different wing shapes, even though the pattern of sexual shape dimorphism remained the same for both fruits. These results show the influence of the host fruits on adult fruit fly morphology, a phenomenon that must be considered when implementing pest control programs such as the Sterile Insect Technique (SIT). Further studies are needed to explore mating preference and genetic structure between these populations

An Overview

This work was financed by national funds from FCT—Fundação para a Ciência e a Tecnologia, I.P., in the scope of the projects LA/P/0037/2020 of the Associate Laboratory Institute of Nanostructures, Nanomodelling and Nanofabrication—i3N. European Cooperation in Science & Technology (COST) Action European Topology Interdisciplinary Action (PhoBioS CA21159). Publisher Copyright: © 2023 by the authors.Catastrophic oil spill accidents, oily industrial wastewater, and other types of uncontrolled release of oils into the environment are major global issues since they threaten marine ecosystems and lead to a big economic impact. It can also affect the public health of communities near the polluted area. This review addresses the different types of oil collecting methods. The focus of this work will be on the different approaches to materials and technologies for oil/water separation, with a special focus on water/oil emulsion separation. Emulsified oil/water mixtures are extremely stable dispersions being, therefore, more difficult to separate as the size of the droplets in the emulsion decreases. Oil-absorbent materials, such as sponges, foams, nanoparticles, and aerogels, can be adjusted to have both hydrophobic and oleophilic wettability while displaying a porous structure. This can be advantageous for targeting oil spills in large-scale environmental and catastrophic sets since these materials can easily absorb oil. Oil adsorbent materials, for example, meshes, textiles, membranes, and clays, involve the capture of the oily material to the surface of the adsorbent material, additionally attracting more attention than other technologies by being low-cost and easy to manufacture.publishersversionpublishe

Hierarchical wrinkling on elastometric Janus spheres

Hierarchical wrinkling on elastomeric Janus spheres is permanently imprinted by swelling, for different lengths of time, followed by drying the particles in an appropriate solvent. First-order buckling with a spatial periodicity (lambda(11)) of the order of a few microns and hierarchical structures comprising of 2nd order buckling with a spatial periodicity (lambda(12)) of the order of hundreds of nanometers have been obtained. The 2nd order buckling features result from a Grinfeld surface instability due to the diffusion of the solvent and the presence of sol molecules

New native host plant records for frugivorous flies (Diptera: Tephritidae, Lonchaeidae) in Northeastern Brazil

The fruit flies Anastrepha fraterculus (Wiedemann, 1830), Anastrepha sororcula Zucchi, 1979, Ceratitis capitata (Wiedemann, 1824) (Diptera: Tephritidae) and Neosilba pendula (Bezzi, 1989) (Diptera: Lonchaeidae) are recorded for the first time emerging from Campomanesia dichotoma (O.Berg) Mattos and Campomanesia ilhoensis Mattos (Myrtaceae), two native species occurring in fragments of Atlantic Forest over dunes, in the northernmost limit of this biome in the state of Rio Grande do Norte, Brazil. The flies emerged from fruit samples obtained at the conservation area at Parque Estadual Dunas do Natal. The parasitoids that emerged from the puparia were also recorded, with Aganaspis pelleranoi (Brèthes) being recorded for the first time for the state. These records are of importance for monitoring and further understanding of the cycles on alternative hosts especially where these species are considered agricultural pests.

Conductive electrospun Polyaniline/Polyvinylpyrrolidone nanofibers: Electrical and morphological characterization of new yarns for electronic textiles

UID/CTM/50025/2019Advanced functionalities textiles embedding electronic fibers, yarns and fabrics are a demand for innovative smart cloths. Conductive electrospun membranes and yarns based on polyaniline/polyvinylpyrrolidone (PANI/PVP) were investigated using the chemical modification of PANI instead of using conventional coating processes as in-situ polymerization. PANI was synthesized from the aniline monomer and the influence of the oxidant-to-monomer ratio on electrical conductivity was studied. The optimized conductivity of pellets made with pressed PANI powders was 21 S·cm-1. Yarns were then prepared from the t-Boc-PANI/PVP electrospun membranes followed by PANI protonation to enhance their electrical properties. Using this methodology, electrospun membranes and yarns were produced with electrical conductivities of 1.7 x 10-2 and 4.1 x 10-4 S·cm-1.publishersversionpublishe

Novel information on the cranial anatomy of the tapejarine pterosaur Caiuajara dobruskii

Caiuajara dobruskii is a tapejarid pterosaur from the Cretaceous of the 'Cemitério dos Pterossauros' (pterosaur graveyard) site, a unique pterosaur bonebed which is located at the municipality of Cruzeiro do Oeste (Paraná, Brazil). Preliminary inferences on Caiuajara morphology were founded on a few partial skeletons, with no detail on the skull anatomy. Here we describe a new specimen from the pterosaur graveyard site, which corresponds to the most complete skull of Caiuajara dobruskii known so far. Furthermore, we describe and compare other specimens including the holotype, a paratype, and several other undescribed specimens. The new specimen preserves the posterior portion of the skull, allowing a better comprehension of its morphology and provides an appreciation of the anatomic structures of the basicranium, enabling better interpretation of this region. We also described the lower jaw of Caiuajara, reporting a unique feature of its symphyseal which adds to the diagnosis for the species. A variability in the premaxillary crest is also noted in different specimens of Caiuajara, which might be interpreted as sexual dimorphism or ontogenetic variability. Therefore, those new findings allow a better comprehension of its skull and enables a more precise comparison between the skulls of those extinct flying reptiles

Rheo-optical characterization of liquid crystalline acetoxypropylcellulose melt undergoing large shear flow and relaxation after flow cessation

The rheological and structural characteristics of acetoxypropylcellulose (APC) nematic melt are studied at shear rates ranging from 10 s 1 to 1000 s 1 which are relevant to extrusion based processes. APC shows a monotonic shear thinning behavior over the range of shear rates tested. The negative extrudate-swell shows a minimum when a critical shear rate g_ c is reached. For shear rates smaller than g_ c, the flowinduced texture consists of two set of bands aligned parallel and normal to the flow direction. At shear rates larger than g_ c, the flow induced texture is reminiscent of a 2 fluids structure. Close to the shearing walls, domains elongated along the flow direction and stacked along the vorticity are imaged with POM, whereas SALS patterns indicate that the bulk of the sheared APC is made of elliptical domains oriented along the vorticity. No full nematic alignment is achieved at the largest shear rate tested. Below g_ c, the stress relaxation is described by a stretched exponential. Above g_ c, the stress relaxation is described by a fast and a slow process. The latter coincides with the growth of normal bands thicknesses, as the APC texture after flow cessation consists of two types of bands with parallel and normal orientations relative to the flow direction. Both bands thicknesses do not depend on the applied shear rate, in contrast to their orientation.This work was partially supported by the Portuguese Science and Technology Foundation through projects, PTDC/CTM/099595/2008, PTDC/CTM/101776/2008, PTDC/CTM-POL/1484/2012 and UID/CTM/500025/2013. S.N. Fernandes and J.P. Canejo acknowledge FCT for grants SFRH/BPD/78430/2011 and SFRH/BPD/101041/2014, respectively. Funding for project "Matepro e Optimizing Materials and Processes", with reference NORTE-07-0124-FEDER-000037 FEDER COMPETE, is also acknowledged

Investigating Asphalt Self-Healing with Colorless Binder and Pigmented Rejuvenator

This work was financed by national funds from FCT—Fundação para a Ciência e a Tecnologia, I.P., in the scope of the project LA/P/0037/2020. The authors would like to acknowledge the support given to this research by REPSOL and RAVAGO CHEMICALS, providing the binder and the red pellet pigment, respectively. © 2023 by the authors. Licensee MDPI, Basel, SwitzerlandDespite asphalt self-healing with encapsulated rejuvenators having been intensively researched over the last decade, there is still uncertainty about the performance advantages granted by this technology. As a way of adding to the existing set of research methodologies, this study aimed to test the feasibility of a visual method to investigate the working mechanism of encapsulated rejuvenators in the bituminous mixture. For this purpose, clear bituminous mixtures were produced using a colorless synthetic binder and a pigment was added to the rejuvenator incorporated in the calcium alginate capsules. The internal structure of the bituminous mixtures containing these capsules was inspected both on loaded and unloaded specimens. The colored rejuvenator was also directly added to cracked specimens and its distribution was studied, along with the interaction between the rejuvenator and the synthetic binder. The results show that the rejuvenator could modify the binder to a limited extent, and the bituminous mixtures containing capsules showed evidence of rejuvenator release. It is demonstrated that the aggregate gradation of mixtures has a significant effect on capsule damage and rejuvenator release. However, the pigment can be filtrated from the rejuvenator by the capsule polymer structure and the asphalt. Even though the methodology presented some constraints, it has been proven to be capable of achieving the initial goal, while also acting as an important first step in the visual study of rejuvenator release in asphalt.publishersversionpublishe