8,360 research outputs found
A 0.8 V T Network-Based 2.6 GHz Downconverter RFIC
A 2.6 GHz downconverter RFIC is designed and implemented using a 0.18 μm CMOS standard process. An important goal of the design is to achieve the high linearity that is required in WiMAX systems with a low supply voltage. A passive T phase-shift network is used as an RF input stage in a Gilbert cell to reduce supply voltage. A single supply voltage of 0.8 V is used with a power consumption of 5.87 mW. The T network-based downconverter achieves a conversion gain (CG) of 5 dB, a single-sideband noise figure (NF) of 16.16 dB, an RF-to-IF isolation of greater than 20 dB, and an input-referred third-order intercept point (IIP3) of 1 dBm when the LO power of -13 dBm is applied
Modelling the impact of infection control measures on the incidence of vancomycin-resistance enterococci: a time-series analysis
Numerical methods for analyzing electromagnetic scattering
Numerical methods to analyze electromagnetic scattering are presented. The dispersions and attenuations of the normal modes in a circular waveguide coated with lossy material were completely analyzed. The radar cross section (RCS) from a circular waveguide coated with lossy material was calculated. The following is observed: (1) the interior irradiation contributes to the RCS much more than does the rim diffraction; (2) at low frequency, the RCS from the circular waveguide terminated by a perfect electric conductor (PEC) can be reduced more than 13 dB down with a coating thickness less than 1% of the radius using the best lossy material available in a 6 radius-long cylinder; (3) at high frequency, a modal separation between the highly attenuated and the lowly attenuated modes is evident if the coating material is too lossy, however, a large RCS reduction can be achieved for a small incident angle with a thin layer of coating. It is found that the waveguide coated with a lossy magnetic material can be used as a substitute for a corrugated waveguide to produce a circularly polarized radiation yield
Numerical methods for analyzing electromagnetic scattering
Attenuation properties of the normal modes in an overmoded waveguide coated with a lossy material were analyzed. It is found that the low-order modes, can be significantly attenuated even with a thin layer of coating if the coating material is not too lossy. A thinner layer of coating is required for large attenuation of the low-order modes if the coating material is magnetic rather than dielectric. The Radar Cross Section (RCS) from an uncoated circular guide terminated by a perfect electric conductor was calculated and compared with available experimental data. It is confirmed that the interior irradiation contributes to the RCS. The equivalent-current method based on the geometrical theory of diffraction (GTD) was chosen for the calculation of the contribution from the rim diffraction. The RCS reduction from a coated circular guide terminated by a PEC are planned schemes for the experiments are included. The waveguide coated with a lossy magnetic material is suggested as a substitute for the corrugated waveguide
Wave attenuation and mode dispersion in a waveguide coated with lossy dielectric material
The modal attenuation constants in a cylindrical waveguide coated with a lossy dielectric material are studied as functions of frequency, dielectric constant, and thickness of the dielectric layer. A dielectric material best suited for a large attenuation is suggested. Using Kirchhoff's approximation, the field attenuation in a coated waveguide which is illuminated by a normally incident plane wave is also studied. For a circular guide which has a diameter of two wavelengths and is coated with a thin lossy dielectric layer (omega sub r = 9.1 - j2.3, thickness = 3% of the radius), a 3 dB attenuation is achieved within 16 diameters
First passage times and asymmetry of DNA translocation
Motivated by experiments in which single-stranded DNA with a short hairpin
loop at one end undergoes unforced diffusion through a narrow pore, we study
the first passage times for a particle, executing one-dimensional brownian
motion in an asymmetric sawtooth potential, to exit one of the boundaries. We
consider the first passage times for the case of classical diffusion,
characterized by a mean-square displacement of the form , and for the case of anomalous diffusion or subdiffusion, characterized by a
mean-square displacement of the form with
. In the context of classical diffusion, we obtain an expression
for the mean first passage time and show that this quantity changes when the
direction of the sawtooth is reversed or, equivalently, when the reflecting and
absorbing boundaries are exchanged. We discuss at which numbers of `teeth'
(or number of DNA nucleotides) and at which heights of the sawtooth potential
this difference becomes significant. For large , it is well known that the
mean first passage time scales as . In the context of subdiffusion, the
mean first passage time does not exist. Therefore we obtain instead the
distribution of first passage times in the limit of long times. We show that
the prefactor in the power relation for this distribution is simply the
expression for the mean first passage time in classical diffusion. We also
describe a hypothetical experiment to calculate the average of the first
passage times for a fraction of passage events that each end within some time
. We show that this average first passage time scales as in
subdiffusion.Comment: 10 pages, 4 figures We incorporated reviewers' suggestions from
Physical Review E. We reformulated a few paragraphs in the introduction and
further clarified the issue of the (a)symmetry of passage times. In the
results section, we re-expressed the results in a form that manifest the
important features. We also added a few references concerning anomalous
diffusion. The look (but not the content) of figure 1 was also change
- …