214 research outputs found
Quench propagation and detection in the superconducting bus-bars of the ATLAS magnets
The ATLAS superconducting magnet system comprising Barrel (BT) and End-Cap Toroids (ECT) and also Central Solenoid (CS) will store more than 1.5 GJ of magnetic energy. The magnet system will have many superconducting busbars, a few meters long each, running from the current leads to Central Solenoid and Toroids as well as between the coils of each Toroid. Quench development in the busbars, i.e., the normal zone propagation process along the busbar superconductors, is slow and exhibits very low voltages. Therefore, its timely and appropriate detection represents a real challenge. The temperature evolution in the busbars under quench is of primary importance. Conservative calculations of the temperature were performed for all the magnets. Also, a simple and effective method to detect a normal zone in a busbar is presented. A thin superconducting wire, whose normal resistance can be easily detected, is placed in a good thermal contact to busbar. Thus, the wire can operate as straightforward and low-noise quench-detector. (4 refs)
The ATLAS magnet test facility at CERN
The magnet system for the ATLAS detector at CERN consists of a Barrel Toroid (BT), two End-Cap Toroids (ECT) and a Central Solenoid (CS). The overall dimensions of the system are 20 m in diameter by 26 m in length. Before underground installation all coils will be tested on surface in a magnet test facility which is under construction. Moreover two model coils are tested as well as subsystems. In this paper the design and construction of the test facility is presented. (3 refs)
Recommended from our members
The Effect of Magnetic Field on the Position of HTS Leads and theCooler in the Services Tower of the MICE Focusing Magnet
The MICE focusing solenoids have three 4 K coolers (two forthe superconducting magnet and one for the liquid absorber) and four HTSleads that feed the current to the focusing coils. The focusing solenoidsproduce large radial external fields when they operate with the polarityof the two coils in opposition (the gradient or flip mode). When the MICEfocusing coils operate at the same polarity (the solenoid or non-flipmode), the fields are much smaller and parallel to the axis of thesolenoid. The worst-case magnetic field affects the selection of thecooler and the HTS leads. This magnetic field can also determine theheight of the service towers that house the three coolers and the fourHTS leads. This paper shows the criteria used for Cooler selection, HTSlead selection, and the position of both the cooler and leads withrespect to the solenoid axis of rotation
AmrZ is a major determinant of c-di-GMP levels in Pseudomonas fluorescens F113
The transcriptional regulator AmrZ is a global regulatory protein conserved within the pseudomonads. AmrZ can act both as a positive and a negative regulator of gene expression, controlling many genes implicated in environmental adaption. Regulated traits include motility, iron homeostasis, exopolysaccharides production and the ability to form biofilms. In Pseudomonas fluorescens F113, an amrZ mutant presents a pleiotropic phenotype, showing increased swimming motility, decreased biofilm formation and very limited ability for competitive colonization of rhizosphere, its natural habitat. It also shows different colony morphology and binding of the dye Congo Red. The amrZ mutant presents severely reduced levels of the messenger molecule cyclic-di-GMP (c-di-GMP), which is consistent with the motility and biofilm formation phenotypes. Most of the genes encoding proteins with diguanylate cyclase (DGCs) or phosphodiesterase (PDEs) domains, implicated in c-di-GMP turnover in this bacterium, appear to be regulated by AmrZ. Phenotypic analysis of eight mutants in genes shown to be directly regulated by AmrZ and encoding c-di-GMP related enzymes, showed that seven of them were altered in motility and/or biofilm formation. The results presented here show that in P. fluorescens, AmrZ determines c-di-GMP levels through the regulation of a complex network of genes encoding DGCs and PDEs
Recommended from our members
Liquid Cryogen Absorber for MICE
The Muon Ionization Cooling Experiment (MICE) will test ionization cooling of muons. In order to have effective ionization cooling, one must use an absorber that is made from a low-z material. The most effective low z materials for ionization cooling are hydrogen, helium, lithium hydride, lithium and beryllium, in that order. In order to measure the effect of material on cooling, several absorber materials must be used. This report describes a liquid-hydrogen absorber that is within a pair of superconducting focusing solenoids. The absorber must also be suitable for use with liquid helium. The following absorber components are discussed in this report; the absorber body, its heat exchanger, the hydrogen system, and the hydrogen safety. Absorber cooling and the thin windows are not discussed here
Recommended from our members
The Physical Connection and Magnetic Coupling of the MICE Cooling Channel Magnets and the Magnet Forces for Various MICE OperatingModes
A key issue in the construction of the MICE cooling channel is the magnetic forces between various elements in the cooling channel and the detector magnets. This report describes how the MICE cooling channel magnets are hooked to together so that the longitudinal magnetic forces within the cooling channel can be effectively connected to the base of the experiment. This report presents a magnetic force and stress analysis for the MICE cooling channel magnets, even when longitudinal magnetic forces as large as 700 kN (70 tons) are applied to the vacuum vessel of various magnets within the MICE channel. This report also shows that the detector magnets can be effectively separated from the central MICE cooling channel magnets without damage to either type of magnet component
- …