Numerical modelling of porosity with combined gas and shrinkage effects in HPDC

High-pressure die casting is a manufacturing process in which near-net-shape components are produced rapidly under a pressurized environment. However, due to the relatively higher cooling rate prevailing during the process, isolated liquid pockets form at certain locations, leading to increased porosity formation. A one-dimensional deformable grid numerical model has been developed for predicting the evolution of a single pore in an elementary volume, which combines the diffusion model with the shrinkage affected growth. The model accounts for the change in pore size due to shrinkage and inter-granular growth. This model can provide predictions in representative volumes and be used for component level predictions by combining with a macroscopic model

Role of the local stress systems on microstructural inhomogeneity during semisolid injection

High pressure metal die casting is an extremely dynamic process with widely ranging cooling rates and intensifying pressures, resulting in a wide range of solid fractions and deformation rates simultaneously existing in the same casting. These process parameters and their complex interplay dictate the formation of microstructural solidification defects. In this study, fast synchrotron X-ray imaging experiments simulating high pressure die casting of aluminium alloys were conducted to investigate the effect of solid fraction, loading conditions and semisolid flow on local microstructural inhomogeneity. While most of the existing literature in this field reports speeds up to 10 µm/s for in situ deformation, the present work captures much faster filling and solidification, at speeds closer to 100 µm/s and at different solid fractions. Semisolid deformation of low solid fractions reveals two typical microstructural features: (i) coarser grains in the middle and finer ones near the walls, and (ii) remelting near the solid-liquid interface due to Cu enrichment in the liquid by the flow. Ex situ scans and digital image correlation analysis of the higher solid fraction samples reveal a porosity formation mechanism based on the local state of stresses, microstructure and feeding. Four different characteristics were identified: (i) plug flow, (ii) dead zone (densified mush), (iii) shear and (iv) bulk zones. These insights will be used to develop zone-specific strategies for the numerical modelling of defect formation during die casting

Effects of strain rate on hot tear formation in Al-Si-Cu alloys

The alloy casting process is one of the major manufacturing processes to produce near net shape components. The casing process is prone to a wide variety of defects, with hot tear being one of the most detrimental. The two main factors generally recognized as the primary cause for formation of hot tears are the mechanical response of the mush (which effects its permeability), and the solidification range (solidification time). The response of the mushy zone under deformation is mainly affected by the solid fraction, strain rate and grain morphology. Even though the science behind the formation of hot tear is understood, there is no general criterion to quantify the hot tear formation under varying casting conditions. The development of ultra-fast X-ray imaging has facilitated the means to quantify the effects of the critical parameters in-situ and develop better correlations for hot tear prediction. The in situ experiments will also provide insights into mush rheology, which has significant influence on hot tear formation. In this study, isothermal semi solid compression studies of Al-Si-Cu alloys were carried out using specially built thermo-mechanical rig. We studied the effects of the strain rate in the range of 2 × 10^{-4} –0.02/s and solid fraction (~0.6-0.9) on the mechanical response of the mushy zone. The sample were characterized before and after deformation using X-ray micro tomography. The data was subjected to an image processing routine and the amount of porosity and hot tear was quantified. The stress-strain curve of the semisolid alloys showed a characteristic strain softening behaviour for semi solid samples with ~0.6-0.7 solid fraction, irrespective of loading rates, whereas the behaviour at higher fractions were that of constant flow stress. Additionally, in situ compression experiments were carried out, wherein the liquid channel thickness at various strain values were measured. Isolated liquid channels were formed under loading, from where the hot tears were found to nucleate. Hot tear susceptibility was found to increase with increasing strain rate and rheology of the mush, which is dependent on solid fraction

Pore evolution mechanisms during directed energy deposition additive manufacturing.

Porosity in directed energy deposition (DED) deteriorates mechanical performances of components, limiting safety-critical applications. However, how pores arise and evolve in DED remains unclear. Here, we reveal pore evolution mechanisms during DED using in situ X-ray imaging and multi-physics modelling. We quantify five mechanisms contributing to pore formation, migration, pushing, growth, removal and entrapment: (i) bubbles from gas atomised powder enter the melt pool, and then migrate circularly or laterally; (ii) small bubbles can escape from the pool surface, or coalesce into larger bubbles, or be entrapped by solidification fronts; (iii) larger coalesced bubbles can remain in the pool for long periods, pushed by the solid/liquid interface; (iv) Marangoni surface shear flow overcomes buoyancy, keeping larger bubbles from popping out; and (v) once large bubbles reach critical sizes they escape from the pool surface or are trapped in DED tracks. These mechanisms can guide the development of pore minimisation strategies

Role of the local stress systems on microstructural inhomogeneity during semisolid injection

High pressure metal die casting is an extremely dynamic process with widely ranging cooling rates and intensifying pressures, resulting in a wide range of solid fractions and deformation rates simultaneously existing in the same casting. These process parameters and their complex interplay dictate the formation of microstructural solidification defects. In this study, fast synchrotron X-ray imaging experiments simulating high pressure die casting of aluminium alloys were conducted to investigate the effect of solid fraction, loading conditions and semisolid flow on local microstructural inhomogeneity. While most of the existing literature in this field reports speeds up to 10 µm/s for in situ deformation, the present work captures much faster filling and solidification, at speeds closer to 100 µm/s and at different solid fractions. Semisolid deformation of low solid fractions reveals two typical microstructural features: (i) coarser grains in the middle and finer ones near the walls, and (ii) remelting near the solid-liquid interface due to Cu enrichment in the liquid by the flow. Ex situ scans and digital image correlation analysis of the higher solid fraction samples reveal a porosity formation mechanism based on the local state of stresses, microstructure and feeding. Four different characteristics were identified: (i) plug flow, (ii) dead zone (densified mush), (iii) shear and (iv) bulk zones. These insights will be used to develop zone-specific strategies for the numerical modelling of defect formation during die casting

Combined deformation and solidification-driven porosity formation in aluminum alloys

In die-casting processes, the high cooling rates and pressures affect the alloy solidification and deformation behavior, and thereby impact the final mechanical properties of cast components. In this study, isothermal semi-solid compression and subsequent cooling of aluminum die-cast alloy specimens were characterized using fast synchrotron tomography. This enabled the investigation and quantification of gas and shrinkage porosity evolution during deformation and solidification. The analysis of the 4D images (3D plus time) revealed two distinct mechanisms by which porosity formed; (i) deformation-induced growth due to the enrichment of local hydrogen content by the advective hydrogen transport, as well as a pressure drop in the dilatant shear bands, and (ii) diffusion-controlled growth during the solidification. The rates of pore growth were quantified throughout the process, and a Gaussian distribution function was found to represent the variation in the pore growth rate in both regimes. Using a one-dimensional diffusion model for hydrogen pore growth, the hydrogen flux required for driving pore growth during these regimes was estimated, providing a new insight into the role of advective transport associated with the deformation in the mushy region

Previous cesarean section and abortion as risk factors for developing placenta previa

Journal of Obstetrics and Gynaecology Research252137-142JOGR

Ovarian hyperstimulation syndrome is associated with reversible impairment of vascular reactivity

10.1016/S0015-0282(02)04392-3Fertility and Sterility7861159-1163FEST

Effects of strain rate on hot tear formation in Al-Si-Cu alloys

The alloy casting process is one of the major manufacturing processes to produce near net shape components. The casing process is prone to a wide variety of defects, with hot tear being one of the most detrimental. The two main factors generally recognized as the primary cause for formation of hot tears are the mechanical response of the mush (which effects its permeability), and the solidification range (solidification time). The response of the mushy zone under deformation is mainly affected by the solid fraction, strain rate and grain morphology. Even though the science behind the formation of hot tear is understood, there is no general criterion to quantify the hot tear formation under varying casting conditions. The development of ultra-fast X-ray imaging has facilitated the means to quantify the effects of the critical parameters in-situ and develop better correlations for hot tear prediction. The in situ experiments will also provide insights into mush rheology, which has significant influence on hot tear formation. In this study, isothermal semi solid compression studies of Al-Si-Cu alloys were carried out using specially built thermo-mechanical rig. We studied the effects of the strain rate in the range of 2 × 10-4–0.02/s and solid fraction (∼0.6-0.9) on the mechanical response of the mushy zone. The sample were characterized before and after deformation using X-ray micro tomography. The data was subjected to an image processing routine and the amount of porosity and hot tear was quantified. The stress-strain curve of the semisolid alloys showed a characteristic strain softening behaviour for semi solid samples with ∼0.6-0.7 solid fraction, irrespective of loading rates, whereas the behaviour at higher fractions were that of constant flow stress. Additionally, in situ compression experiments were carried out, wherein the liquid channel thickness at various strain values were measured. Isolated liquid channels were formed under loading, from where the hot tears were found to nucleate. Hot tear susceptibility was found to increase with increasing strain rate and rheology of the mush, which is dependent on solid fraction

Post-Market Surgeon Safety Outcomes and Experience Performing Laparoscopic Ultrasound-Guided Radiofrequency Ablation using the Acessa™ System

Study Objective: 1) Evaluate intraoperative and near-term safety outcomes following laparoscopic radiofrequency ablation of fibroids (Lap-RFA) performed by gynecologic surgeons new to the procedure, using the Acessa™ system (Acessa Health, Austin, TX, USA). 2) Compare observed complication rates with those from the pivotal study. Design: Post-market, prospective, single-arm, multicenter analysis; 4-8 weeks’ follow-up. Setting: Community and university hospitals in the U.S. and Canada. Patients or Participants: Surgeons (N=29) with varying levels of laparoscopic surgery experience participating in the ongoing, multinational Treatment Results of Uterine Sparing Technologies (TRUST) randomized clinical trial. Patients were premenopausal women (N=110), aged ≥18 years, enrolled as either run-in patients or randomized to the TRUST Lap-RFA arm. Interventions: During run-in, surgeons received proctored Lap-RFA training. Following training, and after performing ≥2 procedures, surgeons provided feedback using a standardized form. Measurements and Main Results: The primary endpoints were acute intraoperative and serious near-term postoperative complications, defined as occurring \u3c48 hours and 48 hours to ≤30 days post-procedure, respectively, and to compare these outcomes to pivotal study results. Per protocol, surgeons performed 105 procedures (mean number proctored cases per surgeon, 2.48); 100 of the 105 patients were followed at all time points to 30 days. No intraoperative or acute serious complications were reported in this study, unlike the pivotal study where there were 2 acute serious complications (atelectasis and colon injury, 1.46%). Similar to the pivotal study, 1 near-term complication (0.96%) related to uterine entry/manipulation occurred (fever of unknown origin requiring hospitalization), and was categorized as probably device-related. The patient was treated and discharged. Twenty-six surgeons completed the evaluation form; none reported experiencing any problems with the procedure. Conclusion: There were no significant differences in safety outcomes when comparing the pre- and post-market studies. Minimally invasive gynecologic surgeons can safely learn the Lap-RFA procedure with acceptable outcomes after 2-3 proctored cases