577 research outputs found
Concrete beams reinforced with carbon laminates strips bonded into slits
A strengthening technique based on carbon laminate (CFRP) strips applied into slits cut on the concrete cover, and bonded to concrete by epoxy adhesive, was used for increasing the load bearing capacity of concrete beams failed by bending. This technique avoids the occurrence of the peeling phenomenon, mobilizes high percentage of the full strengthening capacity of the CFRP used, and provides higher protection against fire and vandalism. The adopted strengthening technique is briefly described and the main results obtained are presented and discussed. Using a numerical model developed for non-linear analysis of reinforced concrete structures, the response of the beams tested was predicted. The applicability of this kind of models in such type of reinforced concrete structures is commented
Desempenho de três técnicas de reforço à flexão de vigas de betão armado com CFRP
No reforço de estruturas com materiais compósitos (CFRP) as técnicas mais correntes recorrem à
colagem dos CFRP (laminados e mantas) nas faces externas dos elementos a reforçar. Nos
últimos anos tem vindo a ser estudada uma técnica de reforço baseada na inserção de faixas de
laminado de CFRP no betão de recobrimento das peças a reforçar. Neste trabalho procede-se à
análise comparativa da eficácia de reforço destas técnicas
Flexural strengthening of concrete beams with CFRP laminates bonded into slits
Near surface mounted (NSM) strengthening technique using carbon fibre reinforced polymer (CFRP) laminate strips was applied
for doubling the load carrying capacity of concrete beams failing in bending. This objective was attained and the deformational
capacity of the strengthened beams was similar to the corresponding reference beams. The NSM technique has provided a significant increment of the load at serviceability limit state, as well as, the stiffness after concrete cracking. The maximum strain in the CFRP laminates has attained values between 62% and 91% of its ultimate strain. A numerical strategy was developed to simulate the deformational behaviour of RC beams strengthened by NSM technique. Not only the load carrying capacity of the tested beams was well predicted, but also the corresponding deflection
Reforço à flexão de vigas de betão armado por intermédio da inserção de laminados de CFRP no betão de recobrimento
Nos últimos anos tem vindo a ser caracterizada uma técnica de reforço baseada na inserção de
faixas de laminado de fibras de carbono em entalhes realizados no betão de recobrimento das
peças a reforçar. Esta técnica foi aplicada no reforço de vigas de betão armado, com o objectivo
de duplicar a capacidade de carga das vigas de referência, armadas com quatro distintas
percentagens de armadura convencional. Este objectivo foi conseguido, tendo as vigas reforçadas
apresentado ductilidade elevada. Neste trabalho os procedimentos associados à técnica de reforço
são transcritos, os ensaios efectuados são descritos, os resultados obtidos são apresentados e
analisados e os mecanismos de rotura ocorridos são interpretados
Africanidades na escola – possibilidades de uma educação inclusiva para a diversidade
"Série Anais dos XII Colóquio sobre Questões Curriculares, VIII Colóquio Luso-Brasileiro de Currículo e II Colóquio LusoAfro-Brasileiro de Questões Curriculares, vol. 1"O processo educativo brasileiro tem sido marcado por significativas influências relacionadas ao racismo e preconceito contra o negro, consequentemente, contra toda a sua contribuição e potencial educativo, em espaços formais, para nossos jovens e crianças. Neste sentido, realizamos uma investigação, em programa de doutoramento, sobre a contribuição da cultura corporal, em particular, da capoeira, samba e maculele, no processo de educação formal, explorado através de um conjunto de ações que designamos de enriquecimento curricular (AEC), considerando o impacto na formação de questões ligadas à prática pedagógica, formação de professores e atuação social, com motivo da utilização da matriz afro-descendente como principio para construção do conhecimento, articulada através de um processo de desenvolvimento curricular integrado.CIEC - Centro de Investigação em Estudos da Criança, IE, UMinho (UI 317 da FCT), PortugalEste trabalho foi financiado por Fundos Nacionais através da FCT (Fundação para a Ciência e a Tecnologia) e co-financiado pelo Fundo Europeu de Desenvolvimento Regional (FEDER) através do COMPETE 2020 – Programa Operacional Competitividade e Internacionalização (POCI) no âmbito do CIEC (Centro de Investigação em Estudos da Criança da Universidade do Minho) com a referência POCI-01-0145-FEDER-007562info:eu-repo/semantics/publishedVersio
Relação da posição dos terceiros molares inferiores inclusos com as complicações pós-operatórias
Dissertação para obtenção do grau de Mestre no Instituto Universitário Egas MonizObjetivos: Este estudo tem como objetivo comparar a posição clínica e radiográfica dos
terceiros molares inferiores inclusos com as complicações pós-operatórias associadas.
Materiais e Métodos: O presente estudo inclui uma amostra de 43 atos clínicos de
doentes submetidos à extração de terceiros molares inclusos inferiores, para os quais
existisse uma radiografia panorâmica recente, onde fosse possível classificar o dente
segundo a classificação de Pell e Gregory e de Winter. Após uma semana foi registado,
numa folha de recolha de dados, as complicações pós-operatórias. Os dados relativos à
dor foram recolhidos através do preenchimento de uma ficha por parte do paciente, em
que este indicava o valor correspondente ao nível de dor sentido no 1º, 3º e 7º dia após a cirurgia. A distância interincisiva do paciente foi medida no dia da extração e após uma
semana.
Resultados: Dos 43 terceiros molares inferiores inclusos analisados a posição mais
frequente foi a mesioangular (44,2%) e em relação ao grau de retenção de Pell e Gregory foi a II (48,8%) e a A (41,9%). As posições com mais complicações pós-operatórias foram a II, a B e a mesioangular, porém não foi estatisticamente significativo a relação entre as complicações pós-operatórias e a classificação de Winter (p>0,05) e entre as classes I, II e III (p>0,05). A dor foi a única complicação em que houve uma diferença significativa (p=0,003) entre as classes A, B e C.
Conclusão: A posição mandibular do terceiro molar incluso pode estar relacionada ao
desenvolvimento de complicações pós-operatórias, porém a única relação que obteve
resultados significativos foi entre a dor e as classes A, B e C.Objectives: This study aims to compare the clinical and radiographic position of the
impacted lower third molars with the associated postoperative complications.
Materials and Methods: The present study includes a sample of 43 clinical acts of
patients that undergone extraction of the impacted lower third molars, for which a recent
panoramic radiograph existed, where it was possible to classify the tooth according to the
classification of Pell and Gregory and of Winter. After one week, postoperative
complications were registered on a data collection sheet. Data related to pain were
collected by filling out a form by the patient, which indicated the value corresponding to
the pain level felt on the 1st, 3rd and 7th day after surgery.
Results: Of the 43 impacted lower third molars analyzed, the most frequent position was
the mesioangular position (44.2%) and in relation to the Pell and Gregory classification
was the II (48.8%) and A (41.9%). The positions with the most postoperative complications were II, B and mesioangular, however the relationship between
postoperative complications and Winter classification and between classes I, II and III
was not statistically significant (p> 0.05). Pain was the only complication in which there
was a significant difference (p = 0.003) between classes A, B and C.
Conclusion: The mandibular position of the impacted third molar may be related to the
development of postoperative complications, but the only relationship that obtained
significant results was between pain and classes A, B and C
Study of surface free energy on a lattice-gas model applied to Liquid bridge
The pulmonary crackling and the formation of liquid bridges are problems that for centuries have been attracting the attention of scientists. In order to study these phenomena, it was developed a canonical cubic lattice-gas like model to explain the rupture of liquid bridges in lung airways [A. Alencar et al., 2006, PRE]. Here, we further develop this model and add entropy analysis to study thermodynamic properties, such as free energy and force. The simulations were performed using the Monte Carlo method with Metropolis algorithm. The exchange between gas and liquid particles were performed randomly according to the Kawasaki dynamics and weighted by the Boltzmann factor. Each particle, which can be solid (s), liquid (l) or gas (g), has 26 neighbors: 6 + 12 + 8, with distances 1, √2 and √3, respectively. The energy of a lattice's site m is calculated by the following expression:\ud
Em = ∑k=126 Ji(m)j(k) in witch (i, j) = g, l or s. Specifically, it was studied the surface free\ud
energy of the liquid bridge, trapped between two planes, when its height is changed. For that, was considered two methods. First, just the internal energy was calculated. Then was considered the entropy. It was fond no difference in the surface free energy between this two methods. We calculate the liquid bridge force between the two planes using the numerical surface free energy. This force is strong for small height, and decreases as the distance between the two planes, height, is increased. The liquid-gas system was also characterized studying the variation of internal energy and heat capacity with the temperature. For that, was performed simulation with the same proportion of liquid and gas particle, but different lattice size. The scale of the liquid-gas system was also studied, for low temperature, using different values to the interaction Jij.CNPqFAPES
Elementos de casca em alvenaria cerâmica reforçados com laminados de fibras de carbono
Este trabalho refere-se a um estudo experimental efectuado sobre elementos de casca em alvenaria cerâmica
com juntas e camada de compressão em betão simples, reforçados com laminados de CFRP para esforços de flexão. No
reforço utilizaram-se duas técnicas: laminados colados sobre a superfície do betão das juntas; laminados inseridos em
entalhes executados no betão das juntas. Os resultados obtidos demonstram a eficiência das técnicas de reforço utilizadas,
dado se ter registado um substancial aumento da capacidade resistente e das condições de segurança dos elementos
ensaiados.Shell elements made by ceramic units bonded by concrete joints and covered by a concrete compression
layer were strengthening by strips of carbon fiber reinforced polymer laminates (CFRP), using two reinforcing techniques:
CFRP laminates externally bonded to concrete joints, CFRP laminates bonded into slits made on the concrete joints. Both
reinforcing techniques have shown to be effective in terms of increasing the ultimate load and its corresponding
deformability, but the last one was more effectiveness. In the present work the experimental research is described and the
main results are presented and discussed
Vigas de betão armado reforçadas com laminados de CFRP inseridos no betão de recobrimento
Relatório 02-DEC/E-1
- …