Digital predistortion of wideband radar waveforms

As demands for increased radio frequency system performance have grown over time, sufficiently mitigating the distortion introduced by high power amplifiers has proven to be a major challenge to overcome. Digital predistortion is one technique commonly used to reduce the distortion products seen at the output of amplifiers, to great effect. While some of the most widely used predistortion algorithms to date may seem most applicable to waveforms with properties most commonly seen in wireless communication systems, it will be seen that with some specialization, these methods can be quite applicable to linear frequency-modulated pulse radar waveforms. In this thesis, a frequency-domain approach to parameter estimation is presented, and a simple window-based approach to predistortion of wideband linear frequency-modulated pulses is also explored. To test the performance of these predistortion algorithms, a modular radar signal processing FPGA testbench architecture is discussed. Finally, a software defined radio was used to measure the performance of the algorithms discussed in this thesis, and a significant improvement in the peak range sidelobe level was observed. These results enable the integration of digital predistortion into modern radar systems with minimal computational overhead to correct radar pulse envelope distortion

Linearization techniques to suppress optical nonlinearity

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.This thesis is shown the implementation of the linearization techniques such as feedforward and pre-distortion feedback linearization to suppress the optical components nonlinearities caused by the fibre and semiconductor optical amplifier (SOA). The simulation verified these two linearization techniques for single tone direct modulation, two tone indirect modulation and ultra wideband input to the optical fibre. These techniques uses the amplified spontaneously emission (ASE) noise reduction in two loops of SOA by a feed-forward and predistortion linearizer and is shown more than 6dB improvement. Also it investigates linearization for the SOA amplifier to cancel out the third order harmonics or inter-modulation distortion (IMD) or four waves mixing. In this project, more than 20 dB reductions is seen in the spectral re-growth caused by the SOA. Amplifier non-linearity becomes more severe with two strong input channels leading to inter-channel distortion which can completely mask a third adjacent channel. The simulations detailed above were performed utilizing optimum settings for the variable gain, phase and delay components in the error correction loop of the feed forward and Predistortion systems and hence represent the ideal situation of a perfect feed-forward and Predistortion system. Therefore it should be consider that complexity of circuit will increase due to amplitude, phase and delay mismatches in practical design. Also it has describe the compatibility of Software Defined Radio with Hybrid Fibre Radio with simulation model of wired optical networks to be used for future research investigation, based on the star and ring topologies for different modulation schemes, and providing the performance for these configurations

Nonlinear Equalization and Digital Pre-Distortion Techniques for Future Radar and Communications Digital Array Systems

Modern radar (military, automotive, weather, etc.) and communication systems seek to leverage the spatio-spectral efficiency of phased arrays. Specifically, there is an increasingly large demand for fully-digital arrays, with each antenna element having its own transmitter and receiver. Further, in order to makes these systems realizable, low-cost, low-complexity solutions are required, often sacrificing the system's linearity. Lower linearity paired with the inherent lack of RF spacial filtering can make these highly digital systems vulnerable to high-power interferering signals-- potentially introducing spectral regrowth and/or gain compression, distorting the signal-of-interest. Digital linearization solutions such as Digital Pre-Distiortion (DPD) and Nonlinear Equalization (NLEQ) have been shown to effectively mitigate nonlinearities for transmitters and receivers, respectively. Further, DPD and NLEQ seek to extend the effective dynamic range of digital arrays, helping the systems reach their designed dynamic range improvement of $10\log_{10}(N)$~dB, where $N$ is the number of transmitters/receivers. However, the performance of these solutions is ultimately determined by training model and waveform. Further, the nonlinear characteristics of a system can change with temperature, frequency, power, time, etc., requiring a robust calibration technique to maintain a high-level of nonlinear mitigation. This dissertation reviews the different types of nonlinear models and the current NLEQ and DPD algorithms for digital array systems. Further, a generalized calibration waveform for both NLEQ and DPD is proposed, allowing a system to maximize its dynamic range over power and frequency. Additionally, an \textit{in-situ} calibration method, leveraging the inherent mutual coupling in an array, is proposed as a solution to maintaining a high level of performance in a fielded digital array system over the system's lifetime. The combination of the proposed training waveform and \textit{in-situ} calibration technique prove to be very effective at adaptively creating a generalized solution to extending the dynamic range of future low-cost digital array systems

Caracterização, modelação e compensação de efeitos de memória lenta em amplificadores de potência baseados em GAN HEMTS

Gallium nitride (GaN) high-electron-mobility transistors (HEMTs) have emerged as the most compelling technology for the transmission of highpower radio-frequency (RF) signals for cellular mobile communications and radar applications. However, despite their remarkable power capabilities, the deployment of GaN HEMT-based RF power amplifiers (PAs) in the mobile communications infrastructure is often ruled out in favor of alternative siliconbased technologies. One of the main reasons for this is the pervasiveness of nonlinear long-term memory effects in GaN HEMT technology caused by thermal and charge-trapping phenomena. While these effects can be compensated for using sophisticated digital predistortion algorithms, their implementation and model-extraction complexity—as well as the power necessary for their real-time execution—make them unsuitable for modern small cells and large-scale multiple-input multiple-output transceivers, where the power necessary for the linearization of each amplification element is of great concern. In order to address these issues and further the deployment of high-powerdensity high-efficiency GaN HEMT-based RF PAs in next-generation communications and radar applications, in this thesis we propose novel methods for the characterization, modeling, and compensation of long-term memory effects in GaN HEMT-based RF PAs. More specifically, we propose a method for the characterization of the dynamic self-biasing behavior of GaN HEMTbased RF PAs; multiple behavioral models of charge trapping and their implementation as analog electronic circuits for the accurate real-time prediction of the dynamic variation of the threshold voltage of GaN HEMTs; a method for the compensation of the pulse-to-pulse instability of GaN HEMT-based RF PAs for radar applications; and a hybrid analog/digital scheme for the linearization of GaN HEMT-based RF PAs for next-generation communications applications.Os transístores de alta mobilidade eletrónica de nitreto de gálio (GaN HEMTs) são considerados a tecnologia mais atrativa para a transmissão de sinais de radiofrequência de alta potência para comunicações móveis celulares e aplicações de radar. No entanto, apesar das suas notáveis capacidades de transmissão de potência, a utilização de amplificadores de potência (PAs) baseados em GaN HEMTs é frequentemente desconsiderada em favor de tecnologias alternativas baseadas em transístores de silício. Uma das principais razões disto acontecer é a existência pervasiva na tecnologia GaN HEMT de efeitos de memória lenta causados por fenómenos térmicos e de captura eletrónica. Apesar destes efeitos poderem ser compensados através de algoritmos sofisticados de predistorção digital, estes algoritmos não são adequados para transmissores modernos de células pequenas e interfaces massivas de múltipla entrada e múltipla saída devido à sua complexidade de implementação e extração de modelo, assim como a elevada potência necessária para a sua execução em tempo real. De forma a promover a utilização de PAs de alta densidade de potência e elevada eficiência baseados em GaN HEMTs em aplicações de comunicação e radar de nova geração, nesta tese propomos novos métodos de caracterização, modelação, e compensação de efeitos de memória lenta em PAs baseados em GaN HEMTs. Mais especificamente, nesta tese propomos um método de caracterização do comportamento dinâmico de autopolarização de PAs baseados em GaN HEMTs; vários modelos comportamentais de fenómenos de captura eletrónica e a sua implementação como circuitos eletrónicos analógicos para a previsão em tempo real da variação dinâmica da tensão de limiar de condução de GaN HEMTs; um método de compensação da instabilidade entre pulsos de PAs baseados em GaN HEMTs para aplicações de radar; e um esquema híbrido analógico/digital de linearização de PAs baseados em GaN HEMTs para comunicações de nova geração.Programa Doutoral em Telecomunicaçõe

Mixed-Signal Multimode Radio Software/Hardware Development Platform

Radio frequency power amplifiers (PAs) are the most challenging part of the design of radio systems since they dictate the overall system's performance in terms of power efficiency and distortion generation. The performance is further challenged by modern modulation schemes which are characterized by highly varying signal envelopes. In order to meet the spectrum mask requirements, PAs are usually operated at high power back-off to ensure linearity, at the cost of efficiency. To tackle this issue, many efficiency enhancement techniques have been presented in the literature. In fact, these techniques do increase the PA power efficiency at back-off, however, efficiency enhancement techniques do not ensure the linearity of the PA. Furthermore, these techniques may lead to additional distortion. On the other hand, several linearization techniques have been developed to mitigate the PA nonlinearity problem and allow the PA to operate at less back-off. Digital Pre-Distortion (DPD) technique is gaining more attention, as compared to other linearization techniques, thanks to its simple concept and advancements in digital signal processors (DSP) and signal converters. DPD technique consists of introducing a nonlinear function before the PA so that the overall cascaded system behaves linearly. It was clear from the literature that this technique showed good performance. Yet, it has primarily been validated using commercial test equipment, which has good capabilities, and far from the real world environment in which this technique would be implemented. Indeed, DPDs would need to be implemented in signal processors characterised by limited resources and computational accuracy. This thesis presents an implementation of several DPD models, namely look-up table (LUT), memoryless polynomial and memory polynomial (MP), on a field programmable gate array (FPGA). A novel model reformulation made this implementation possible in fixed-point arithmetic. Measurements were collected to validate the DPD models' implementation and an improvement of the signal quality was recorded in terms of error vector magnitude (EVM) and adjacent channel leakage ratio (ACLR). As many wireless access technologies must continue to coexist, multi-standard radio systems are required to reduce the cost while maintaining the interoperability. This thesis presents a development platform for multimode radio which comprises mixed-signal modules. The platform provides the capacity for hardware and software development. In fact, the FPGA under investigation allowed for the implementation of a baseband transceiver and DPD schemes. In addition, a software tool was developed as a dashboard to control and monitor the system. The radio system in the platform was optimized through the equalization of the feedback receiver frequency response performed through a simultaneous measurement of the amplitude ripple of the transmitter and receiver. Furthermore, a phase-coherent frequency synthesizer was designed to bring more flexibility by allowing the transmitter's carrier frequency to be different from the receiver's frequency

Vidutinių dažnių 5G belaidžių tinklų galios stiprintuvų tyrimas

This dissertation addresses the problems of ensuring efficient radio fre-quency transmission for 5G wireless networks. Taking into account, that the next generation 5G wireless network structure will be heterogeneous, the device density and their mobility will increase and massive MIMO connectivity capability will be widespread, the main investigated problem is formulated – increasing the efficiency of portable mid-band 5G wireless network CMOS power amplifier with impedance matching networks. The dissertation consists of four parts including the introduction, 3 chapters, conclusions, references and 3 annexes. The investigated problem, importance and purpose of the thesis, the ob-ject of the research methodology, as well as the scientific novelty are de-fined in the introduction. Practical significance of the obtained results, defended state-ments and the structure of the dissertation are also included. The first chapter presents an extensive literature analysis. Latest ad-vances in the structure of the modern wireless network and the importance of the power amplifier in the radio frequency transmission chain are de-scribed in detail. The latter is followed by different power amplifier archi-tectures, parameters and their improvement techniques. Reported imped-ance matching network design methods are also discussed. Chapter 1 is concluded distinguishing the possible research vectors and defining the problems raised in this dissertation. The second chapter is focused around improving the accuracy of de-signing lumped impedance matching network. The proposed methodology of estimating lumped inductor and capacitor parasitic parameters is dis-cussed in detail provi-ding complete mathematical expressions, including a summary and conclusions. The third chapter presents simulation results for the designed radio fre-quency power amplifiers. Two variations of Doherty power amplifier archi-tectures are presented in the second part, covering the full step-by-step de-sign and simulation process. The latter chapter is concluded by comparing simulation and measurement results for all designed radio frequency power amplifiers. General conclusions are followed by an extensive list of references and a list of 5 publications by the author on the topic of the dissertation. 5 papers, focusing on the subject of the discussed dissertation, have been published: three papers are included in the Clarivate Analytics Web of Sci-ence database with a citation index, one paper is included in Clarivate Ana-lytics Web of Science database Conference Proceedings, and one paper has been published in unreferred international conference preceedings. The au-thor has also made 9 presentations at 9 scientific conferences at a national and international level.Dissertatio

A fast engineering approach to high efficiency power amplifier linearization for avionics applications

This PhD thesis provides a fast engineering approach to the design of digital predistortion (DPD) linearizers from several perspectives: i) enhancing the off-line training performance of open-loop DPD, ii) providing robustness and reducing the computational complexity of the parameters identification subsystem and, iii) importing machine learning techniques to favor the automatic tuning of power amplifiers (PAs) and DPD linearizers with several free-parameters to maximize power efficiency while meeting the linearity specifications. One of the essential parts of unmanned aerial vehicles (UAV) is the avionics, being the radio control one of the earliest avionics present in the UAV. Unlike the control signal, for transferring user data (such as images, video, etc.) real-time from the drone to the ground station, large transmission rates are required. The PA is a key element in the transmitter chain to guarantee the data transmission (video, photo, etc.) over a long range from the ground station. The more linear output power, the better the coverage or alternatively, with the same coverage, better SNR allows the use of high-order modulation schemes and thus higher transmission rates are achieved. In the context of UAV wireless communications, the power consumption, size and weight of the payload is of significant importance. Therefore, the PA design has to take into account the compromise among bandwidth, output power, linearity and power efficiency (very critical in battery-supplied devices). The PA can be designed to maximize its power efficiency or its linearity, but not both. Therefore, a way to deal with this inherent trade-off is to design high efficient amplification topologies and let the PA linearizers take care of the linearity requirements. Among the linearizers, DPD linearization is the preferred solution to both academia and industry, for its high flexibility and linearization performance. In order to save as many computational and power resources as possible, the implementation of an open-loop DPD results a very attractive solution for UAV applications. This thesis contributes to the PA linearization, especially on off-line training for open-loop DPD, by presenting two different methods for reducing the design and operating costs of an open-loop DPD, based on the analysis of the DPD function. The first method focuses on the input domain analysis, proposing mesh-selecting (MeS) methods to accurately select the proper samples for a computationally efficient DPD parameter estimation. Focusing in the MeS method with better performance, the memory I-Q MeS method is combined with feature extraction dimensionality reduction technique to allow a computational complexity reduction in the identification subsystem by a factor of 65, in comparison to using the classical QR-LS solver and consecutive samples selection. In addition, the memory I-Q MeS method has been proved to be of crucial interest when training artificial neural networks (ANN) for DPD purposes, by significantly reducing the ANN training time. The second method involves the use of machine learning techniques in the DPD design procedure to enlarge the capacity of the DPD algorithm when considering a high number of free parameters to tune. On the one hand, the adaLIPO global optimization algorithm is used to find the best parameter configuration of a generalized memory polynomial behavioral model for DPD. On the other hand, a methodology to conduct a global optimization search is proposed to find the optimum values of a set of key circuit and system level parameters, that properly combined with DPD linearization and crest factor reduction techniques, can exploit at best dual-input PAs in terms of maximizing power efficiency along wide bandwidths while being compliant with the linearity specifications. The advantages of these proposed techniques have been validated through experimental tests and the obtained results are analyzed and discussed along this thesis.Aquesta tesi doctoral proporciona unes pautes per al disseny de linealitzadors basats en predistorsió digital (DPD) des de diverses perspectives: i) millorar el rendiment del DPD en llaç obert, ii) proporcionar robustesa i reduir la complexitat computacional del subsistema d'identificació de paràmetres i, iii) incorporació de tècniques d'aprenentatge automàtic per afavorir l'auto-ajustament d'amplificadors de potència (PAs) i linealitzadors DPD amb diversos graus de llibertat per poder maximitzar l’eficiència energètica i al mateix temps acomplir amb les especificacions de linealitat. Una de les parts essencials dels vehicles aeris no tripulats (UAV) _es l’aviònica, sent el radiocontrol un dels primers sistemes presents als UAV. Per transferir dades d'usuari (com ara imatges, vídeo, etc.) en temps real des del dron a l’estació terrestre, es requereixen taxes de transmissió grans. El PA _es un element clau de la cadena del transmissor per poder garantir la transmissió de dades a grans distàncies de l’estació terrestre. A major potència de sortida, més cobertura o, alternativament, amb la mateixa cobertura, millor relació senyal-soroll (SNR) la qual cosa permet l’ús d'esquemes de modulació d'ordres superiors i, per tant, aconseguir velocitats de transmissió més altes. En el context de les comunicacions sense fils en UAVs, el consum de potència, la mida i el pes de la càrrega útil són de vital importància. Per tant, el disseny del PA ha de tenir en compte el compromís entre ample de banda, potència de sortida, linealitat i eficiència energètica (molt crític en dispositius alimentats amb bateries). El PA es pot dissenyar per maximitzar la seva eficiència energètica o la seva linealitat, però no totes dues. Per tant, per afrontar aquest compromís s'utilitzen topologies amplificadores d'alta eficiència i es deixa que el linealitzador s'encarregui de garantir els nivells necessaris de linealitat. Entre els linealitzadors, la linealització DPD és la solució preferida tant per al món acadèmic com per a la indústria, per la seva alta flexibilitat i rendiment. Per tal d'estalviar tant recursos computacionals com consum de potència, la implementació d'un DPD en lla_c obert resulta una solució molt atractiva per a les aplicacions UAV. Aquesta tesi contribueix a la linealització del PA, especialment a l'entrenament fora de línia de linealitzadors DPD en llaç obert, presentant dos mètodes diferents per reduir el cost computacional i augmentar la fiabilitat dels DPDs en llaç obert. El primer mètode se centra en l’anàlisi de l’estadística del senyal d'entrada, proposant mètodes de selecció de malla (MeS) per seleccionar les mostres més significatives per a una estimació computacionalment eficient dels paràmetres del DPD. El mètode proposat IQ MeS amb memòria es pot combinar amb tècniques de reducció del model del DPD i d'aquesta manera poder aconseguir una reducció de la complexitat computacional en el subsistema d’identificació per un factor de 65, en comparació amb l’ús de l'algoritme clàssic QR-LS i selecció de mostres d'entrenament consecutives. El segon mètode consisteix en l’ús de tècniques d'aprenentatge automàtic pel disseny del DPD quan es considera un gran nombre de graus de llibertat (paràmetres) per sintonitzar. D'una banda, l'algorisme d’optimització global adaLIPO s'utilitza per trobar la millor configuració de paràmetres d'un model polinomial amb memòria generalitzat per a DPD. D'altra banda, es proposa una estratègia per l’optimització global d'un conjunt de paràmetres clau per al disseny a nivell de circuit i sistema, que combinats amb linealització DPD i les tècniques de reducció del factor de cresta, poden maximitzar l’eficiència de PAs d'entrada dual de gran ample de banda, alhora que compleixen les especificacions de linealitat. Els avantatges d'aquestes tècniques proposades s'han validat mitjançant proves experimentals i els resultats obtinguts s'analitzen i es discuteixen al llarg d'aquesta tesi

Millimetre-wave and Terahertz Electronics

Overview: The basic thesis for the advancement of millimetre-wave and terahertz electronics is represented in four sections: Signal Processing, Component Design and Realization, Modelling and Materials, and Paradigm Shift. The first section is at system and circuit levels and reports on complex signal process functions that have been performed directly on the millimetre-wave carrier signal, intended for realizing low-cost and adaptive communications and radar systems architectures. The second section is at circuit and component levels and reports on techniques for the design and realization of low-loss passives for use at millimetrewave frequencies. The third section is at component and material levels and reports on modelling techniques for passives for use at both millimetre-wave and terahertz frequencies. Finally, the fourth section introduces a revolutionary new technology that represents a paradigm shift in the way millimetre-wave and terahertz electronics (i.e. components, circuits and systems) can be implemented. As found with the new generation of mobile phone handsets, a fusion of two extreme technologies can take place; here, complex signal processing operations could be performed both directly on the carrier signal and with the use of a spatial light modulator. Based on a selection of 20 papers (co-)authored by the candidate †b, and published over a period of 15 years, it will be seen that a coherent theme runs throughout this body of work, for the advancement of knowledge in millimetre-wave and terahertz electronics