Realization of Low-Voltage Modified CBTA and Design of Cascadable Current-Mode All-Pass Filter

In this paper, a low voltage modified current backward transconductance amplifier (MCBTA) and a novel first-order current-mode (CM) all-pass filter are presented. The MCBTA can operate with ±0.9 V supply voltage and the total power consumption of MCBTA is 1.27 mW. The presented all-pass filter employs single MCBTA, a grounded resistor and a grounded capacitor. The circuit possesses low input and high output impedances which make it ideal for current-mode systems. The presented all-pass filter circuit can be made electronically tunable due to the bias current of the MCBTA. Non-ideal study along with simulation results are given for validation purpose. Further, an nth-order cascadable all-pass filter is also presented. It uses n MCBTAs, n grounded resistors and n grounded capacitors. The performance of the proposed circuits is demonstrated by using PSPICE simulations based on the 0.18 µm TSMC level-7 CMOS technology parameters

Low-Voltage High-Linearity Wideband Current Differencing Transconductance Amplifier and Its Application on Current-Mode Active Filter

A low-voltage high-linearity wideband current differencing transconductance amplifier (CDTA) is presented in this paper. The CDTA consists of a current differencing circuit and a cross-coupling transconductance circuit. The PSPICE simulations of the proposed CDTA show a good performance: -3dB frequency bandwith is about 900 MHz, low power consumption is 2.48 mW, input current linear range is ±100 µA and low current-input resistance is less than 20 Ω, high current-output resistance is more than 3 MΩ. PSpice simulations for a current-mode universal filter and a proposed high-order filter are also conducted, and the results verify the validity of the proposed CDTA

A wideband linear tunable CDTA and its application in field programmable analogue array

This document is the Accepted Manuscript version of the following article: Hu, Z., Wang, C., Sun, J. et al. ‘A wideband linear tunable CDTA and its application in field programmable analogue array’, Analog Integrated Circuits and Signal Processing, Vol. 88 (3): 465-483, September 2016. Under embargo. Embargo end date: 6 June 2017. The final publication is available at Springer via https://link.springer.com/article/10.1007%2Fs10470-016-0772-7 © Springer Science+Business Media New York 2016In this paper, a NMOS-based wideband low power and linear tunable transconductance current differencing transconductance amplifier (CDTA) is presented. Based on the NMOS CDTA, a novel simple and easily reconfigurable configurable analogue block (CAB) is designed. Moreover, using the novel CAB, a simple and versatile butterfly-shaped FPAA structure is introduced. The FPAA consists of six identical CABs, and it could realize six order current-mode low pass filter, second order current-mode universal filter, current-mode quadrature oscillator, current-mode multi-phase oscillator and current-mode multiplier for analog signal processing. The Cadence IC Design Tools 5.1.41 post-layout simulation and measurement results are included to confirm the theory.Peer reviewedFinal Accepted Versio

Novel active function blocks and their applications in frequency filters and quadrature oscillators

Kmitočtové filtry a sinusoidní oscilátory jsou lineární elektronické obvody, které jsou používány v široké oblasti elektroniky a jsou základními stavebními bloky v analogovém zpracování signálu. V poslední dekádě pro tento účel bylo prezentováno velké množství stavebních funkčních bloků. V letech 2000 a 2006 na Ústavu telekomunikací, VUT v Brně byly definovány univerzální proudový konvejor (UCC) a univerzální napět'ový konvejor (UVC) a vyrobeny ve spolupráci s firmou AMI Semiconductor Czech, Ltd. Ovšem, stále existuje požadavek na vývoj nových aktivních prvků, které nabízejí nové výhody. Hlavní přínos práce proto spočívá v definici dalších původních aktivních stavebních bloků jako jsou differential-input buffered and transconductance amplifier (DBTA), current follower transconductance amplifier (CFTA), z-copy current-controlled current inverting transconductance amplifier (ZC-CCCITA), generalized current follower differential input transconductance amplifier (GCFDITA), voltage gain-controlled modified current-feedback operational amplifier (VGC-MCFOA), a minus-type current-controlled third-generation voltage conveyor (CC-VCIII-). Pomocí navržených aktivních stavebních bloků byly prezentovány původní zapojení fázovacích článků prvního řádu, univerzální filtry druhého řádu, ekvivalenty obvodu typu KHN, inverzní filtry, aktivní simulátory uzemněného induktoru a kvadraturní sinusoidní oscilátory pracující v proudovém, napět'ovém a smíšeném módu. Chování navržených obvodů byla ověřena simulací v prostředí SPICE a ve vybraných případech experimentálním měřením.Frequency filters and sinusoidal oscillators are linear electric circuits that are used in wide area of electronics and also are the basic building blocks in analogue signal processing. In the last decade, huge number of active building blocks (ABBs) were presented for this purpose. In 2000 and 2006, the universal current conveyor (UCC) and the universal voltage conveyor (UVC), respectively, were designed at the Department of Telecommunication, BUT, Brno, and produced in cooperation with AMI Semiconductor Czech, Ltd. There is still the need to develop new active elements that offer new advantages. The main contribution of this thesis is, therefore, the definition of other novel ABBs such as the differential-input buffered and transconductance amplifier (DBTA), the current follower transconductance amplifier (CFTA), the z-copy current-controlled current inverting transconductance amplifier (ZC-CCCITA), the generalized current follower differential input transconductance amplifier (GCFDITA), the voltage gain-controlled modified current-feedback operational amplifier (VGC-MCFOA), and the minus-type current-controlled third-generation voltage conveyor (CC-VCIII-). Using the proposed ABBs, novel structures of first-order all-pass filters, second-order universal filters, KHN-equivalent circuits, inverse filters, active grounded inductance simulators, and quadrature sinusoidal oscillators working in the current-, voltage-, or mixed-mode are presented. The behavior of the proposed circuits has been verified by SPICE simulations and in selected cases also by experimental measurements.

Dual-mode multifunction filter realized with a single voltage differencing gain amplifier (VDGA)

This article presents the dual-mode multifunction biquad filter realized employing only a single voltage differencing gain amplifier (VDGA), one resistor and three capacitors. The proposed filterwith one input and three outputs can configure as voltage-mode or current-mode filter circuit with the appropriate input injection choice. It can also synthesis the three standard filter functions, which are highpass, bandpass, and lowpass responses without modifying the circuit configuration. Orthogonal adjustment between the natural angular frequency (o) and the quality factor (Q) of the filter is achieved. Detail analysis of non-ideal VDGA effects and circuit component sensitivity are included. The circuit principle is verified by means of simulation results with TSMC 0.35-m CMOS process parameters

New Electronically Tunable Third Order Filters and Dual Mode Sinusoidal Oscillator Using VDTAs and Grounded Capacitors

This study introduces a third order filter and a third order oscillator configuration. Both the circuits use two voltage difference transconductance amplifiers (VDTAs) and three grounded capacitors. By selecting the input and output terminals properly, current mode and transimpedance mode low-pass and band-pass filters can be obtained without component matching conditions. The natural frequency (ω0) can be tuned electronically. The oscillator circuit provides voltage and current outputs explicitly. The condition of oscillation (CO) and the frequency of oscillation (FO) can be adjusted orthogonally and electronically. The workability of the configurations is judged using TSMC CMOS 0.18 μm technology parameter as well as commercially available LM13700 integrated circuits (ICs). The simulation results show that: for ±0.9V power supply, the power consumption is 1.08 mW for both the configurations, while total harmonic distortions (THDs) are less than 2.06% and 2.17% for the filter and oscillator configurations, respectively

Current and Voltage Mode Multiphase Sinusoidal Oscillators Using CBTAs

Current-mode (CM) and voltage-mode (VM) multiphase sinusoidal oscillator (MSO) structures using current backward transconductance amplifier (CBTA) are proposed. The proposed oscillators can generate n current or voltage signals (n being even or odd) equally spaced in phase. n+1 CBTAs, n grounded capacitors and a grounded resistor are used for nth-state oscillator. The oscillation frequency can be independently controlled through transconductance (gm) of the CBTAs which are adjustable via their bias currents. The effects caused by the non-ideality of the CBTA on the oscillation frequency and condition have been analyzed. The performance of the proposed circuits is demonstrated on third-stage and fifth-stage MSOs by using PSPICE simulations based on the 0.25 µm TSMC level-7 CMOS technology parameters

Electronically Tunable Voltage-Mode Multiphase Sinusoidal Oscillator with Low Output Impedance Nodes Employing VD-DIBAs

The multiphase sinusoidal oscillator (MSO) is useful for various electrical and electronic applications. This study aims to design an MSO employing voltage differencing differential input buffered amplifiers (VD-DIBAs). The design procedure is based on cascading the first-order low-pass filter. Each phase consists of a VD-DIBA, two resistors, and a grounded capacitor. An odd-phase system without requiring an additional amplifier. The frequency is electronically controlled through the bias current without affecting the condition. The sinewave amplitudes and the phase difference between each waveform are identical. The proposed MSO is designed to obtain three-phase waveforms (n = 3). PSPICE simulation demonstrates the performance of the proposed oscillator with 0.18 μm TSMC CMOS parameters with ±0.9 V power supply. The feasibility of the proposed MSO is also verified with experiments using the VD-DIBA constructed from commercial integrated circuits (ICs) with a ±5 V power supply. The simulated and experimental results align with theoretical predictions

Current mode fractional order filters using VDTAs with Grounded capacitors

In this work, the design of current mode Fractional order filter using VDTAs (Voltage differencing trans-conductance amplifier) as an active element with grounded capacitors has been proposed. The approximate transfer functions of low and high pass filters of fractional order on the basis of the integer order transfer has been shown and the form of those functions of filters is also implemented using VDTA as an active building block. In this work, filters of the different sequence have been realized. The frequency domain simulation results of the proposed filters are obtained on Matlab and PSPICE with TSMC CMOS 180 nm technology parameters. Stability and sensitivity is also verifie

A Novel (DDCC-SFG)-Based Systematic Design Technique of Active Filters

This paper proposes a novel idea for the synthesis of active filters that is based on the use of signal-flow graph (SFG) stamps of differential difference current conveyors (DDCCs). On the basis of an RLC passive network or a filter symbolic transfer function, an equivalent SFG is constructed. DDCCs’ SFGs are identified inside the constructed ‘active’ graph, and thus the equivalent circuit can be easily synthesized. We show that the DDCC and its ‘derivatives’, i.e. differential voltage current conveyors and the conventional current conveyors, are the main basic building blocks in such design. The practicability of the proposed technique is showcased via three application examples. Spice simulations are given to show the viability of the proposed technique