Vector Generation for Maximum Instantaneous Current Through Supply Lines for CMOS Circuits

Abstract We present two new algorithms for generating a small set of patterns for estimating the maximum instantaneous current through the power supply lines for CMOS circuits. The rst algorithm is based on timed ATPG, while the second is a probability-based approach. Both algorithms can handle circuits with arbitrary but known delays and they produce a set of 2-vector tests. Experimental results demonstrating that the outcome of applying our algorithms is a small set of patterns producing a current that is a tight l o w er bound on the maximum instantaneous current are included

Supply Current Modeling and Analysis of Deep Sub-Micron Cmos Circuits

Continued technology scaling has introduced many new challenges in VLSI design. Instantaneous switching of the gates yields high current flow through them that causes large voltage drop at the supply lines. Such high instantaneous currents and voltage drop cause reliability and performance degradation. Reliability is an issue as high magnitude of current can cause electromigration, whereas, voltage drop can slow down the circuit performance. Therefore, designing power supply lines emphasizes the need of computing maximum current through them. However, the development of digital integrated circuits in short design cycle requires accurate and fast timing and power simulation. Unfortunately, simulators that employ device modeling methods, such as HSPICE are prohibitively slow for large designs. Therefore, methods which can produce good maximum current estimates in short times are critical. In this work a compact model has been developed for maximum current estimation that speeds up the computation by orders of magnitude over the commercial tools

Impact of parameter variations on circuits and microarchitecture

Parameter variations, which are increasing along with advances in process technologies, affect both timing and power. Variability must be considered at both the circuit and microarchitectural design levels to keep pace with performance scaling and to keep power consumption within reasonable limits. This article presents an overview of the main sources of variability and surveys variation-tolerant circuit and microarchitectural approaches.Peer ReviewedPostprint (published version

On the nature and effect of power distribution noise in CMOS digital integrated circuits

The thesis reports on the development of a novel simulation method aimed at modelling power distribution noise generated in digital CMOS integrated circuits. The simulation method has resulted in new information concerning: 1. The magnitude and nature of the power distribution noise and its dependence on the performance and electrical characteristics of the packaged integrated circuit. Emphasis is laid on the effects of resistive, capacitative and inductive elements associated with the packaged circuit. 2. Power distribution noise associated with a generic systolic array circuit comprising 1,020,000 transistors, of which 510,000 are synchronously active. The circuit is configured as a linear array which, if fabricated using two-micron bulk CMOS technology, would be over eight centimetres long and three millimetres wide. In principle, the array will perform 1.5 x 10 to the power of 11 operations per second. 3. Power distribution noise associated with a non-array-based signal processor which, if fabricated in 2-micron bulk CMOS technology, would occupy 6.7 sq. cm. The circuit contains about 900,000 transistors, of which 600,000 are functional and about 300,000 are used for yield enhancement. The processor uses the RADIX-2 algorithm and is designed to achieve 2 x 10 to the power of 8 floating point operations per second. 4. The extent to which power distribution noise limits the level of integration and/ or performance of such circuits using standard and non-standard fabrication and packaging technology. 5. The extent to which the predicted power distribution noise levels affect circuit susceptibility to transient latch-up and electromigration. It concludes the nature of CMOS digital integrated circuit power distribution noise and recommends ways in which it may be minimised. It outlines an approach aimed at mechanising the developed simulation methodology so that the performance of power distribution networks may more routinely be assessed. Finally. it questions the long term suitability of mainly digital techniques for signal processing

Design Solutions For Modular Satellite Architectures

The cost-effective access to space envisaged by ESA would open a wide range of new opportunities and markets, but is still many years ahead. There is still a lack of devices, circuits, systems which make possible to develop satellites, ground stations and related services at costs compatible with the budget of academic institutions and small and medium enterprises (SMEs). As soon as the development time and cost of small satellites will fall below a certain threshold (e.g. 100,000 to 500,000 €), appropriate business models will likely develop to ensure a cost-effective and pervasive access to space, and related infrastructures and services. These considerations spurred the activity described in this paper, which is aimed at: - proving the feasibility of low-cost satellites using COTS (Commercial Off The Shelf) devices. This is a new trend in the space industry, which is not yet fully exploited due to the belief that COTS devices are not reliable enough for this kind of applications; - developing a flight model of a flexible and reliable nano-satellite with less than 25,000€; - training students in the field of avionics space systems: the design here described is developed by a team including undergraduate students working towards their graduation work. The educational aspects include the development of specific new university courses; - developing expertise in the field of low-cost avionic systems, both internally (university staff) and externally (graduated students will bring their expertise in their future work activity); - gather and cluster expertise and resources available inside the university around a common high-tech project; - creating a working group composed of both University and SMEs devoted to the application of commercially available technology to space environment. The first step in this direction was the development of a small low cost nano-satellite, started in the year 2004: the name of this project was PiCPoT (Piccolo Cubo del Politecnico di Torino, Small Cube of Politecnico di Torino). The project was carried out by some departments of the Politecnico, in particular Electronics and Aerospace. The main goal of the project was to evaluate the feasibility of using COTS components in a space project in order to greatly reduce costs; the design exploited internal subsystems modularity to allow reuse and further cost reduction for future missions. Starting from the PiCPoT experience, in 2006 we began a new project called ARaMiS (Speretta et al., 2007) which is the Italian acronym for Modular Architecture for Satellites. This work describes how the architecture of the ARaMiS satellite has been obtained from the lesson learned from our former experience. Moreover we describe satellite operations, giving some details of the major subsystems. This work is composed of two parts. The first one describes the design methodology, solutions and techniques that we used to develop the PiCPoT satellite; it gives an overview of its operations, with some details of the major subsystems. Details on the specifications can also be found in (Del Corso et al., 2007; Passerone et al, 2008). The second part, indeed exploits the experience achieved during the PiCPoT development and describes a proposal for a low-cost modular architecture for satellite

Dynamically Controllable Integrated Radiation and Self-Correcting Power Generation in mm-Wave Circuits and Systems

This thesis presents novel design methodologies for integrated radiators and power generation at mm-wave frequencies that are enabled by the continued integration of various electronic and electromagnetic (EM) structures onto the same substrate. Beginning with the observation that transistors and their connections to EM radiating structures on an integrated substrate are essentially free, the concept of multi-port driven (MPD) radiators is introduced, which opens a vast design space that has been generally ignored due to the cost structure associated with discrete components that favors fewer transistors connected to antennas through a single port. From Maxwell's equations, a new antenna architecture, the radial MPD antennas based on the concept of MPD radiators, is analyzed to gain intuition as to the important design parameters that explain the wide-band nature of the antenna itself. The radiator is then designed and implemented at 160 GHz in a 0.13 um SiGe BiCMOS process, and the single element design has a measured effective isotropic radiated power (EIRP) of +4.6 dBm with a total radiated power of 0.63 mW. Next, the radial MPD radiator is adapted to enable dynamic polarization control (DPC). A DPC antenna is capable of controlling its radiated polarization dynamically, and entirely electronically, with no mechanical reconfiguration required. This can be done by having multiple antennas with different polarizations, or within a single antenna that has multiple drive points, as in the case of the MPD radiator with DPC. This radiator changes its polarization by adjusting the relative phase and amplitude of its multiple ports to produce polarizations with any polarization angle, and a wide range of axial ratios. A 2x1 MPD radiator array with DPC at 105 GHz is presented whose measurements show control of the polarization angle throughout the entire 0 degree through 180 degree range while in the linear polarization mode and maintaining axial ratios above 10 dB in all cases. Control of the axial ratio is also demonstrated with a measured range from 2.4 dB through 14 dB, while maintaining a fixed polarization angle. The radiator itself has a measured maximum EIRP of +7.8 dBm, with a total radiated power of 0.9 mW, and is capable of beam steering. MPD radiators were also applied in the domain of integrated silicon photonics. For these designs, the driver transistor circuitry was replaced with silicon optical waveguides and photodiodes to produce a 350 GHz signal. Three of these optical MPD radiator designs have been implemented as 2x2 arrays at 350 GHz. The first is a beam forming array that has a simulated gain of 12.1 dBi with a simulated EIRP of -2 dBm. The second has the same simulated performance, but includes optical phase modulators that enable two-dimensional beam steering. Finally, a third design incorporates multi-antenna DPC by combining the outputs of both left and right handed circularly polarized MPD antennas to produce a linear polarization with controllable polarization angle, and has a simulated gain of 11.9 dBi and EIRP of -3 dBm. In simulation, it can tune the polarization from 0 degrees through 180 degrees while maintaining a radiated power that has a 0.35 dB maximum deviation from the mean. The reliability of mm-wave radiators and power amplifiers was also investigated, and two self-healing systems have been proposed. Self-healing is a global feedback method where integrated sensors detect the performance of the circuit after fabrication and report that data to a digital control algorithm. The algorithm then is capable of setting actuators that can control the performance of the mm-wave circuit and counteract any performance degradation that is observed by the sensors. The first system is for a MPD radiator array with a partially integrated self-healing system. The self-healing MPD radiator senses substrate modes through substrate mode pickup sensors and infers the far-field radiated pattern from those sensors. DC current sensors are also included to determine the DC power consumption of the system. Actuators are implemented in the form of phase and amplitude control of the multiple drive points. The second self-healing system is a fully integrated self-healing power amplifier (PA) at 28 GHz. This system measures the output power, gain and efficiency of the PA using radio frequency (RF) power sensors, DC current sensors and junction temperature sensors. The digital block is synthesized from VHDL code on-chip and it can actuate the output power combining matching network using tunable transmission line stubs, as well as the DC operating point of the amplifying transistors through bias control. Measurements of 20 chips confirm self-healing for two different algorithms for process variation and transistor mismatch, while measurements from 10 chips show healing for load impedance mismatch, and linearity healing. Laser induced partial and total transistor failure show the benefit of self-healing in the case of catastrophic failure, with improvements of up to 3.9 dB over the default case. An exemplary yield specification shows self-healing improving the yield from 0% up through 80%.</p