Survey on Photo-Voltaic Powered Interleaved Converter System

Renewable energy is the best solution to meet the growing demand for energy in the country. The solar energy is considered as the most promising energy by the researchers due to its abundant availability, eco-friendly nature, long lasting nature, wide range of application and above all it is a maintenance free system. The energy absorbed by the earth can satisfy 15000 times of today’s total energy demand and its hundred times more than that our conventional energy like coal and other fossil fuels. Though, there are overwhelming advantages in solar energy, It has few drawbacks as well such as its low conversion ratio, inconsistent supply of energy due to variation in the sun light, less efficiency due to ripples in the converter, time dependent and, above all, high capitation cost. These aforementioned flaws have been addressed by the researchers in order to extract maximum energy and attain hundred percentage benefits of this heavenly resource. So, this chapter presents a comprehensive investigation based on photo voltaic (PV) system requirements with the following constraints such as system efficiency, system gain, dynamic response, switching losses are investigated. The overview exhibits and identifies the requirements of a best PV power generation system

Power converters and controllers for UPS applications with backup PEM fuel cell

This paper studies the practical cost-effective DC/DC converter, DC/AC inverter and AC/DC rectifier for an uninterruptible power supply (UPS) system with backup proton exchange membrane fuel cell (PEMFC). Furthermore, a comprehensive controller for the PEMFC is designed according to the change of the load, while the energy storage elements, such as battery and ultracapacitor, are chosen in order to compensate the slow dynamic response of PEMFC and to meet the sudden peak load energy demand. The designed power converters can supply high quality power with flexible conversion functions, leading to the establishment of reliable power management for UPS applications. Finally, a suitable control strategy and technique, capable of coping with the change of the load for PEMFC and realizing the energy managements of UPS hybrid system, is implemented. The performances of the proposed power converters and controllers are evaluated by experimental results, showing that the developed UPS system with backup PEMFC and battery power sources is suitable for industry applications. © 2008 IEEE

Design and Control of Power Converters 2020

In this book, nine papers focusing on different fields of power electronics are gathered, all of which are in line with the present trends in research and industry. Given the generality of the Special Issue, the covered topics range from electrothermal models and losses models in semiconductors and magnetics to converters used in high-power applications. In this last case, the papers address specific problems such as the distortion due to zero-current detection or fault investigation using the fast Fourier transform, all being focused on analyzing the topologies of high-power high-density applications, such as the dual active bridge or the H-bridge multilevel inverter. All the papers provide enough insight in the analyzed issues to be used as the starting point of any research. Experimental or simulation results are presented to validate and help with the understanding of the proposed ideas. To summarize, this book will help the reader to solve specific problems in industrial equipment or to increase their knowledge in specific fields

Analysis and Design of High Efficiency Grid-to-Vehicle (G2V) Plug-in Chargers for Local e-Transportation

Electric transportation worldwide has witnessed a tremendous increase in the use of electric vehicles (EV's) due to increased awareness of environmental issues. Road EV's compromise a broad spectrum of vehicles right from two-wheelers three-wheelers (rickshaws/Auto/Trio), cars and electric buses. E-Rickshaw has gained popularity in the Asian market post-2010 because of their symbolic resemblance with traditional auto-rickshaw. The fast growth of the market is principally pushed by the low ownership cost of electric three-wheelers, falling battery prices, and favorable government policies and support. These EVs run on low-cost 48 V, 120 Ah lead acid battery packs having low depth-of-discharge (DOD). Hence, frequent battery charging becomes essential for such EVs. Conventional battery chargers available in the market utilize flyback converter based topologies in order to charge such battery packs. On one hand such battery chargers are easy to implement, these topologies fail to achieve unity power factor (UPF) operation leading to high total harmonic distortion (THD) and poor input power quality at the input. Thus active power factor correction (PFC) becomes a vital constituent in AC-DC converters. By understanding the constraints posed by continuous current mode (CCM) based battery chargers, the proposed converters are designed to operate in discontinuous current mode (DCM) because of its evident benefits such as inherent PFC, zero current turn-on and zero diode reverse recovery losses. By omitting sensors at the input and utilizing only the output sensors, regulated voltage or current can be obtained which makes the system cost-effective and improves its reliability and robustness to high frequency noise. This thesis presents both isolated and non-isolated battery charger for local e-transportation EVs utilizing 48 V lead acid battery pack. At first, a non-isolated single-stage interleaved buck-boost float charger is proposed by considering the advantages such as reduced current stresses, minimum number of semiconductor devices and absence of bulky high frequency transformer. DCM operation of the proposed converter ensure UPF operation for variable input voltage and utilizing just a single sensor makes this charger configuration economical and easy to implement. However, such a configuration had high current stress on the semiconductor devices leading to increased thermal requirement and reduced efficiency at light loads. Thus addressing these problems, a high efficiency two-stage battery charger is proposed. The battery charger uses an interleaved DCM buck-boost converter in order to achieve PFC at variable input voltage, whereas the second stage is an unregulated half-bridge LLC resonant converter which provides isolation as well as soft-switching for the primary switches. Synchronous rectification (SR) along with only capacitive filter is used on center tapped transformer secondary to improve converter efficiency. Due to DCM of the front-end AC-DC converter achieves zero current turn-on of the switches and DC-DC converter switches achieve zero voltage turn-on because of the LLC resonant. The proposed battery charger implements constant current (CC) and constant voltage (CV) method of charging using simple PI controllers, thus making it suitable for commercial use. Small signal models for both the battery charger configurations are developed using the current injected equivalent circuit approach and a detailed controller design is illustrated. Simulation results using PSIM11.1 software and experimental results from proof-of-concept laboratory hardware prototypes are provided in order to validate the reported analysis and design which demonstrates their performance

Design and Control of Power Converters for High Power-Quality Interface with Utility and Aviation Grids

Power electronics as a subject integrating power devices, electric and electronic circuits, control, and thermal and mechanic design, requires not only knowledge and engineering insight for each subarea, but also understanding of interface issues when incorporating these different areas into high performance converter design.Addressing these fundamental questions, the dissertation studies design and control issues in three types of power converters applied in low-frequency high-power transmission, medium-frequency converter emulated grid, and high-frequency high-density aviation grid, respectively, with the focus on discovering, understanding, and mitigating interface issues to improve power quality and converter performance, and to reduce the noise emission.For hybrid ac/dc power transmission,• Analyze the interface transformer saturation issue between ac and dc power flow under line unbalances.• Proposed both passive transformer design and active hybrid-line-impedance-conditioner to suppress this issue.For transmission line emulator,• Propose general transmission line emulation schemes with extension capability.• Analyze and actively suppress the effects of sensing/sampling bias and PWM ripple on emulation considering interfaced grid impedance.• Analyze the stability issue caused by interaction of the emulator and its interfaced impedance. A criterion that determines the stability and impedance boundary of the emulator is proposed.For aircraft battery charger,• Investigate architectures for dual-input and dual-output battery charger, and a three-level integrated topology using GaN devices is proposed to achieve high density.• Identify and analyze the mechanisms and impacts of high switching frequency, di/dt, dv/dt on sensing and power quality control; mitigate solutions are proposed.• Model and compensate the distortion due to charging transition of device junction capacitances in three-level converters.• Find the previously overlooked device junction capacitance of the nonactive devices in three-level converters, and analyze the impacts on switching loss, device stress, and current distortion. A loss calculation method is proposed using the data from the conventional double pulse tester.• Establish fundamental knowledge on performance degradation of EMI filters. The impacts and mechanisms of both inductive and capacitive coupling on different filter structures are understood. Characterization methodology including measuring, modeling, and prediction of filter insertion loss is proposed. Mitigation solutions are proposed to reduce inter-component coupling and self-parasitics

Design and Control of Power Converters 2019

In this book, 20 papers focused on different fields of power electronics are gathered. Approximately half of the papers are focused on different control issues and techniques, ranging from the computer-aided design of digital compensators to more specific approaches such as fuzzy or sliding control techniques. The rest of the papers are focused on the design of novel topologies. The fields in which these controls and topologies are applied are varied: MMCs, photovoltaic systems, supercapacitors and traction systems, LEDs, wireless power transfer, etc

Advances in Control of Power Electronic Converters

This book proposes a list of contributions in the field of control of power electronics converters for different topologies: DC-DC, DC-AC and AC-DC. It particularly focuses on the use of different advanced control techniques with the aim of improving the performances, flexibility and efficiency in the context of several operation conditions. Sliding mode control, fuzzy logic based control, dead time compensation and optimal linear control are among the techniques developed in the special issue. Simulation and experimental results are provided by the authors to validate the proposed control strategies