Approaches to multiprocessor error recovery using an on-chip interconnect subsystem

For future multicores, a dedicated interconnect subsystem for on-chip monitors was found to be highly beneficial in terms of scalability, performance and area. In this thesis, such a monitor network (MNoC) is used for multicores to support selective error identification and recovery and maintain target chip reliability in the context of dynamic voltage and frequency scaling (DVFS). A selective shared memory multiprocessor recovery is performed using MNoC in which, when an error is detected, only the group of processors sharing an application with the affected processors are recovered. Although the use of DVFS in contemporary multicores provides significant protection from unpredictable thermal events, a potential side effect can be an increased processor exposure to soft errors. To address this issue, a flexible fault prevention and recovery mechanism has been developed to selectively enable a small amount of per-core dual modular redundancy (DMR) in response to increased vulnerability, as measured by the processor architectural vulnerability factor (AVF). Our new algorithm for DMR deployment aims to provide a stable effective soft error rate (SER) by using DMR in response to DVFS caused by thermal events. The algorithm is implemented in real-time on the multicore using MNoC and controller which evaluates thermal information and multicore performance statistics in addition to error information. DVFS experiments with a multicore simulator using standard benchmarks show an average 6% improvement in overall power consumption and a stable SER by using selective DMR versus continuous DMR deployment

Low-cost and efficient fault detection and diagnosis schemes for modern cores

Continuous improvements in transistor scaling together with microarchitectural advances have made possible the widespread adoption of high-performance processors across all market segments. However, the growing reliability threats induced by technology scaling and by the complexity of designs are challenging the production of cheap yet robust systems. Soft error trends are haunting, especially for combinational logic, and parity and ECC codes are therefore becoming insufficient as combinational logic turns into the dominant source of soft errors. Furthermore, experts are warning about the need to also address intermittent and permanent faults during processor runtime, as increasing temperatures and device variations will accelerate inherent aging phenomena. These challenges specially threaten the commodity segments, which impose requirements that existing fault tolerance mechanisms cannot offer. Current techniques based on redundant execution were devised in a time when high penalties were assumed for the sake of high reliability levels. Novel light-weight techniques are therefore needed to enable fault protection in the mass market segments. The complexity of designs is making post-silicon validation extremely expensive. Validation costs exceed design costs, and the number of discovered bugs is growing, both during validation and once products hit the market. Fault localization and diagnosis are the biggest bottlenecks, magnified by huge detection latencies, limited internal observability, and costly server farms to generate test outputs. This thesis explores two directions to address some of the critical challenges introduced by unreliable technologies and by the limitations of current validation approaches. We first explore mechanisms for comprehensively detecting multiple sources of failures in modern processors during their lifetime (including transient, intermittent, permanent and also design bugs). Our solutions embrace a paradigm where fault tolerance is built based on exploiting high-level microarchitectural invariants that are reusable across designs, rather than relying on re-execution or ad-hoc block-level protection. To do so, we decompose the basic functionalities of processors into high-level tasks and propose three novel runtime verification solutions that combined enable global error detection: a computation/register dataflow checker, a memory dataflow checker, and a control flow checker. The techniques use the concept of end-to-end signatures and allow designers to adjust the fault coverage to their needs, by trading-off area, power and performance. Our fault injection studies reveal that our methods provide high coverage levels while causing significantly lower performance, power and area costs than existing techniques. Then, this thesis extends the applicability of the proposed error detection schemes to the validation phases. We present a fault localization and diagnosis solution for the memory dataflow by combining our error detection mechanism, a new low-cost logging mechanism and a diagnosis program. Selected internal activity is continuously traced and kept in a memory-resident log whose capacity can be expanded to suite validation needs. The solution can catch undiscovered bugs, reducing the dependence on simulation farms that compute golden outputs. Upon error detection, the diagnosis algorithm analyzes the log to automatically locate the bug, and also to determine its root cause. Our evaluations show that very high localization coverage and diagnosis accuracy can be obtained at very low performance and area costs. The net result is a simplification of current debugging practices, which are extremely manual, time consuming and cumbersome. Altogether, the integrated solutions proposed in this thesis capacitate the industry to deliver more reliable and correct processors as technology evolves into more complex designs and more vulnerable transistors.El continuo escalado de los transistores junto con los avances microarquitectónicos han posibilitado la presencia de potentes procesadores en todos los segmentos de mercado. Sin embargo, varios problemas de fiabilidad están desafiando la producción de sistemas robustos. Las predicciones de "soft errors" son inquietantes, especialmente para la lógica combinacional: soluciones como ECC o paridad se están volviendo insuficientes a medida que dicha lógica se convierte en la fuente predominante de soft errors. Además, los expertos están alertando acerca de la necesidad de detectar otras fuentes de fallos (causantes de errores permanentes e intermitentes) durante el tiempo de vida de los procesadores. Los segmentos "commodity" son los más vulnerables, ya que imponen unos requisitos que las técnicas actuales de fiabilidad no ofrecen. Estas soluciones (generalmente basadas en re-ejecución) fueron ideadas en un tiempo en el que con tal de alcanzar altos nivel de fiabilidad se asumían grandes costes. Son por tanto necesarias nuevas técnicas que permitan la protección contra fallos en los segmentos más populares. La complejidad de los diseños está encareciendo la validación "post-silicon". Su coste excede el de diseño, y el número de errores descubiertos está aumentando durante la validación y ya en manos de los clientes. La localización y el diagnóstico de errores son los mayores problemas, empeorados por las altas latencias en la manifestación de errores, por la poca observabilidad interna y por el coste de generar las señales esperadas. Esta tesis explora dos direcciones para tratar algunos de los retos causados por la creciente vulnerabilidad hardware y por las limitaciones de los enfoques de validación. Primero exploramos mecanismos para detectar múltiples fuentes de fallos durante el tiempo de vida de los procesadores (errores transitorios, intermitentes, permanentes y de diseño). Nuestras soluciones son de un paradigma donde la fiabilidad se construye explotando invariantes microarquitectónicos genéricos, en lugar de basarse en re-ejecución o en protección ad-hoc. Para ello descomponemos las funcionalidades básicas de un procesador y proponemos tres soluciones de `runtime verification' que combinadas permiten una detección de errores a nivel global. Estas tres soluciones son: un verificador de flujo de datos de registro y de computación, un verificador de flujo de datos de memoria y un verificador de flujo de control. Nuestras técnicas usan el concepto de firmas y permiten a los diseñadores ajustar los niveles de protección a sus necesidades, mediante compensaciones en área, consumo energético y rendimiento. Nuestros estudios de inyección de errores revelan que los métodos propuestos obtienen altos niveles de protección, a la vez que causan menos costes que las soluciones existentes. A continuación, esta tesis explora la aplicabilidad de estos esquemas a las fases de validación. Proponemos una solución de localización y diagnóstico de errores para el flujo de datos de memoria que combina nuestro mecanismo de detección de errores, junto con un mecanismo de logging de bajo coste y un programa de diagnóstico. Cierta actividad interna es continuamente registrada en una zona de memoria cuya capacidad puede ser expandida para satisfacer las necesidades de validación. La solución permite descubrir bugs, reduciendo la necesidad de calcular los resultados esperados. Al detectar un error, el algoritmo de diagnóstico analiza el registro para automáticamente localizar el bug y determinar su causa. Nuestros estudios muestran un alto grado de localización y de precisión de diagnóstico a un coste muy bajo de rendimiento y área. El resultado es una simplificación de las prácticas actuales de depuración, que son enormemente manuales, incómodas y largas. En conjunto, las soluciones de esta tesis capacitan a la industria a producir procesadores más fiables, a medida que la tecnología evoluciona hacia diseños más complejos y más vulnerables

45-nm Radiation Hardened Cache Design

abstract: Circuits on smaller technology nodes become more vulnerable to radiation-induced upset. Since this is a major problem for electronic circuits used in space applications, designers have a variety of solutions in hand. Radiation hardening by design (RHBD) is an approach, where electronic components are designed to work properly in certain radiation environments without the use of special fabrication processes. This work focuses on the cache design for a high performance microprocessor. The design tries to mitigate radiation effects like SEE, on a commercial foundry 45 nm SOI process. The design has been ported from a previously done cache design at the 90 nm process node. The cache design is a 16 KB, 4 way set associative, write-through design that uses a no-write allocate policy. The cache has been tested to write and read at above 2 GHz at VDD = 0.9 V. Interleaved layout, parity protection, dual redundancy, and checking circuits are used in the design to achieve radiation hardness. High speed is accomplished through the use of dynamic circuits and short wiring routes wherever possible. Gated clocks and optimized wire connections are used to reduce power. Structured methodology is used to build up the entire cache.Dissertation/ThesisM.S. Electrical Engineering 201

Observation mechanisms for in-field software-based self-test

When electronic systems are used in safety critical applications, as in the space, avionic, automotive or biomedical areas, it is required to maintain a very low probability of failures due to faults of any kind. Standards and regulations play a significant role, forcing companies to devise and adopt solutions able to achieve predefined targets in terms of dependability. Different techniques can be used to reduce fault occurrence or to minimize the probability that those faults produce critical failures (e.g., by introducing redundancy). Unfortunately, most of these techniques have a severe impact on the cost of the resulting product and, in some cases, the probability of failures is too large anyway. Hence, a solution commonly used in several scenarios lies on periodically performing a test able to detect the occurrence of any fault before it produces a failure (in-field test). This solution is normally based on forcing the processor inside the Device Under Test to execute a properly written test program, which is able to activate possible faults and to make their effects visible in some observable locations. This approach is also called Software-Based Self-Test, or SBST. If compared with testing in an end of manufacturing scenario, in-field testing has strong limitations in terms of access to the system inputs and outputs because Design for Testability structures and testing equipment are usually not available. As a consequence there are reduced possibilities to activate the faults and to observe their effects. This reduced observability particularly affects the ability to detect performance faults, i.e. faults that modify the timing but not the final value of computations. This kind of faults are hard to detect by only observing the final content of predefined memory locations, that is the usual test result observation method used in-field. Initially, the present work was focused on fault tolerance techniques against transient faults induced by ionizing radiation, the so called Single Event Upsets (SEUs). The main contribution of this early stage of the thesis lies in the experimental validation of the feasibility of achieving a safe system by using an architecture that combines task-level redundancy with already available IP cores, thus minimizing the development time. Task execution is replicated and Memory Protection is used to guarantee that any SEU may affect one and only one of the replicas. A proof of concept implementation was developed and validated using fault injection. Results outline the effectiveness of the architecture, and the overhead analysis shows that the proposed architecture is effective in reducing the resource occupation with respect to N-modular redundancy, at an affordable cost in terms of application execution time. The main part of the thesis is focused on in-field software-based self-test of permanent faults. A set of observation methods exploiting existing or ad-hoc hardware is proposed, aimed at obtaining a better coverage, in particular of performance faults. An extensive quantitative evaluation of the proposed methods is presented, including a comparison with the observation methods traditionally used in end of manufacturing and in-field testing. Results show that the proposed methods are a good complement to the traditionally used final memory content observation. Moreover, they show that an adequate combination of these complementary methods allows for achieving nearly the same fault coverage achieved when continuously observing all the processor outputs, which is an observation method commonly used for production test but usually not available in-field. A very interesting by-product of what is described above is a detailed description of how to compute the fault coverage achieved by functional in-field tests using a conventional fault simulator, a tool that is usually applied in an end of manufacturing testing scenario. Finally, another relevant result in the testing area is a method to detect permanent faults inside the cache coherence logic integrated in each cache controller of a multi-core system, based on the concurrent execution of a test program by the different cores in a coordinated manner. By construction, the method achieves full fault coverage of the static faults in the addressed logic.Cuando se utilizan sistemas electrónicos en aplicaciones críticas como en las áreas biomédica, aeroespacial o automotriz, se requiere mantener una muy baja probabilidad de malfuncionamientos debidos a cualquier tipo de fallas. Los estándares y normas juegan un papel importante, forzando a los desarrolladores a diseñar y adoptar soluciones que sean capaces de alcanzar objetivos predefinidos en cuanto a seguridad y confiabilidad. Pueden utilizarse diferentes técnicas para reducir la ocurrencia de fallas o para minimizar la probabilidad de que esas fallas produzcan mal funcionamientos críticos, por ejemplo a través de la incorporación de redundancia. Lamentablemente, muchas de esas técnicas afectan en gran medida el costo de los productos y, en algunos casos, la probabilidad de malfuncionamiento sigue siendo demasiado alta. En consecuencia, una solución usada a menudo en varios escenarios consiste en realizar periódicamente un test que sea capaz de detectar la ocurrencia de una falla antes de que esta produzca un mal funcionamiento (test en campo). En general, esta solución se basa en forzar a un procesador existente dentro del dispositivo bajo prueba a ejecutar un programa de test que sea capaz de activar las posibles fallas y de hacer que sus efectos sean visibles en puntos observables. A esta metodología también se la llama auto-test basado en software, o en inglés Software-Based Self-Test (SBST). Si se lo compara con un escenario de test de fin de fabricación, el test en campo tiene fuertes limitaciones en términos de posibilidad de acceso a las entradas y salidas del sistema, porque usualmente no se dispone de equipamiento de test ni de la infraestructura de Design for Testability. En consecuencia se tiene menos posibilidades de activar las fallas y de observar sus efectos. Esta observabilidad reducida afecta particularmente la habilidad para detectar fallas de performance, es decir fallas que modifican la temporización pero no el resultado final de los cálculos. Este tipo de fallas es difícil de detectar por la sola observación del contenido final de lugares de memoria, que es el método usual que se utiliza para observar los resultados de un test en campo. Inicialmente, el presente trabajo estuvo enfocado en técnicas para tolerar fallas transitorias inducidas por radiación ionizante, llamadas en inglés Single Event Upsets (SEUs). La principal contribución de esa etapa inicial de la tesis reside en la validación experimental de la viabilidad de obtener un sistema seguro, utilizando una arquitectura que combina redundancia a nivel de tareas con el uso de módulos hardware (IP cores) ya disponibles, que minimiza en consecuencia el tiempo de desarrollo. Se replica la ejecución de las tareas y se utiliza protección de memoria para garantizar que un SEU pueda afectar a lo sumo a una sola de las réplicas. Se desarrolló una implementación para prueba de concepto que fue validada mediante inyección de fallas. Los resultados muestran la efectividad de la arquitectura, y el análisis de los recursos utilizados muestra que la arquitectura propuesta es efectiva en reducir la ocupación con respecto a la redundancia modular con N réplicas, a un costo accesible en términos de tiempo de ejecución. La parte principal de esta tesis se enfoca en el área de auto-test en campo basado en software para la detección de fallas permanentes. Se propone un conjunto de métodos de observación utilizando hardware existente o ad-hoc, con el fin de obtener una mejor cobertura, en particular de las fallas de performance. Se presenta una extensa evaluación cuantitativa de los métodos propuestos, que incluye una comparación con los métodos tradicionalmente utilizados en tests de fin de fabricación y en campo. Los resultados muestran que los métodos propuestos son un buen complemento del método tradicionalmente usado que consiste en observar el valor final del contenido de memoria. Además muestran que una adecuada combinación de estos métodos complementarios permite alcanzar casi los mismos valores de cobertura de fallas que se obtienen mediante la observación continua de todas las salidas del procesador, método comúnmente usado en tests de fin de fabricación, pero que usualmente no está disponible en campo. Un subproducto muy interesante de lo arriba expuesto es la descripción detallada del procedimiento para calcular la cobertura de fallas lograda mediante tests funcionales en campo por medio de un simulador de fallas convencional, una herramienta que usualmente se aplica en escenarios de test de fin de fabricación. Finalmente, otro resultado relevante en el área de test es un método para detectar fallas permanentes dentro de la lógica de coherencia de cache que está integrada en el controlador de cache de cada procesador en un sistema multi procesador. El método está basado en la ejecución de un programa de test en forma coordinada por parte de los diferentes procesadores. Por construcción, el método cubre completamente las fallas de la lógica mencionad

Design, analysis and optimization of a dynamically reconfi gurable regenerative comparator for ultra-low power 6-bit TC-ADCs in 90nm CMOS technology

In this work the threshold configurable regenerative comparator on which TC-ADCs are based is optimized to further reduce the power consumption for use in battery-less biomedical sensor applications.\nMoreover, the effect of device mismatches on the offset, gain and linearity errors of the ADC is analyzed by means of Monte Carlo simulations.\nThis optimized comparator reduces the power consumption from 13uW to 3uW, while maintaining the same full scale rang

Fault and Defect Tolerant Computer Architectures: Reliable Computing With Unreliable Devices

This research addresses design of a reliable computer from unreliable device technologies. A system architecture is developed for a fault and defect tolerant (FDT) computer. Trade-offs between different techniques are studied and yield and hardware cost models are developed. Fault and defect tolerant designs are created for the processor and the cache memory. Simulation results for the content-addressable memory (CAM)-based cache show 90% yield with device failure probabilities of 3 x 10(-6), three orders of magnitude better than non fault tolerant caches of the same size. The entire processor achieves 70% yield with device failure probabilities exceeding 10(-6). The required hardware redundancy is approximately 15 times that of a non-fault tolerant design. While larger than current FT designs, this architecture allows the use of devices much more likely to fail than silicon CMOS. As part of model development, an improved model is derived for NAND Multiplexing. The model is the first accurate model for small and medium amounts of redundancy. Previous models are extended to account for dependence between the inputs and produce more accurate results

Affordable techniques for dependable microprocessor design

As high computing power is available at an affordable cost, we rely on microprocessor-based systems for much greater variety of applications. This dependence indicates that a processor failure could have more diverse impacts on our daily lives. Therefore, dependability is becoming an increasingly important quality measure of microprocessors.;Temporary hardware malfunctions caused by unstable environmental conditions can lead the processor to an incorrect state. This is referred to as a transient error or soft error. Studies have shown that soft errors are the major source of system failures. This dissertation characterizes the soft error behavior on microprocessors and presents new microarchitectural approaches that can realize high dependability with low overhead.;Our fault injection studies using RISC processors have demonstrated that different functional blocks of the processor have distinct susceptibilities to soft errors. The error susceptibility information must be reflected in devising fault tolerance schemes for cost-sensitive applications. Considering the common use of on-chip caches in modern processors, we investigated area-efficient protection schemes for memory arrays. The idea of caching redundant information was exploited to optimize resource utilization for increased dependability. We also developed a mechanism to verify the integrity of data transfer from lower level memories to the primary caches. The results of this study show that by exploiting bus idle cycles and the information redundancy, an almost complete check for the initial memory data transfer is possible without incurring a performance penalty.;For protecting the processor\u27s control logic, which usually remains unprotected, we propose a low-cost reliability enhancement strategy. We classified control logic signals into static and dynamic control depending on their changeability, and applied various techniques including commit-time checking, signature caching, component-level duplication, and control flow monitoring. Our schemes can achieve more than 99% coverage with a very small hardware addition. Finally, a virtual duplex architecture for superscalar processors is presented. In this system-level approach, the processor pipeline is backed up by a partially replicated pipeline. The replication-based checker minimizes the design and verification overheads. For a large-scale superscalar processor, the proposed architecture can bring 61.4% reduction in die area while sustaining the maximum performance