The auxiliary envelope tracking RF power amplifier system

The advancement of the mobile communication industry increases the need for RF power amplifier (RFPA) to be more efficient and linear. The communication network that is shifting towards smaller micro-cell or nano-cell network has also motivated the design of the RF power amplifier to be simple, compact and cost efficient. In this research work, a novel technique for efficiency and linearity improvement of the RFPA is presented. A simplistic approach in the technique called ‘Auxiliary Envelope Tracking' (AET) system has promoted the design for small and straightforward AET tracking generator, a key component in the system. The use of low cost components in the AET tracking generator has made the technique commercially attractive. The AET technique proposes a separation in generating DC and AC components of the AET signal that biases the drain of the RFPA. The separation eases the generation of the signals resulting in low power consumption that leads to efficiency improvement. The investigation of the gain characteristic of gallium nitride (GaN) RFPA has shown an important RFPA attribute where the gain varied substantially as the drain voltage increases. By using the AET technique, the gain characteristic is harnessed to get linearity improvement. In order to validate the technique, AET measurement systems for two-carrier and WCDMA signals were developed and experimented. A special Class AB RFPA is designed and implemented to use dedicatedly for this investigation. In two-carrier signal measurement, a tracking generator is developed that consists of an envelope amplifier (EA) and a diplexer. The RFPA and the tracking generator are then combined to be an integrated AET block. In order to accommodate the high peak-toaverage ratio (PAR) and high bandwidth WCDMA signal, a broadband RF transformer was designed as part of the AET tracking generator to replace the diplexer. The two-carrier and WCDMA signals measurement results have proven that the AET technique is a valid technique for efficiency and linearity improvement. The improvements were achieved with simple, compact and cost-effective implementation.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Analysis of the lateral diffuse metal-oxide semiconductor (LDMOS) power amplifier for cellular base stations

The primary purpose of this thesis was to present a theoretical large-signal analysis to study the power gain and efficiency of a microwave power amplifier for LS-band communications using software simulation. Power gain, efficiency, reliability, and stability are important characteristics in the power amplifier design process. These characteristics affect advance wireless systems, which require low-cost device amplification without sacrificing system performance. Large-signal modeling and input and output matching components are used for this thesis. Motorola\u27s Electro Thermal LDMOS model is a new transistor model that includes self-heating affects and is capable of small-large signal simulations. It allows for most of the design considerations to be on stability, power gain, bandwidth, and DC requirements. The matching technique allows for the gain to be maximized at a specific target frequency. Calculations and simulations for the microwave power amplifier design were performed using Matlab and Microwave Office respectively. Microwave Office is the simulation software used in this thesis. The study demonstrated that Motorola\u27s Electro Thermal LDMOS transistor in microwave power amplifier design process is a viable solution for common-source amplifier applications in high power base stations. The MET-LDMOS met the stability requirements for the specified frequency range without a stability-improvement model. The power gain of the amplifier circuit was improved through proper microwave matching design using input/output-matching techniques. The gain and efficiency of the amplifier improve approximately 4dB and 7.27% respectively. The gain value is roughly .89 dB higher than the maximum gain specified by the MRF21010 data sheet specifications. This work can lead to efficient modeling and development of high power LDMOS transistor implementations in commercial and industry applications

The auxiliary envelope tracking RF power amplifier system

The advancement of the mobile communication industry increases the need for RF power amplifier (RFPA) to be more efficient and linear. The communication network that is shifting towards smaller micro-cell or nano-cell network has also motivated the design of the RF power amplifier to be simple, compact and cost efficient. In this research work, a novel technique for efficiency and linearity improvement of the RFPA is presented. A simplistic approach in the technique called ‘Auxiliary Envelope Tracking' (AET) system has promoted the design for small and straightforward AET tracking generator, a key component in the system. The use of low cost components in the AET tracking generator has made the technique commercially attractive. The AET technique proposes a separation in generating DC and AC components of the AET signal that biases the drain of the RFPA. The separation eases the generation of the signals resulting in low power consumption that leads to efficiency improvement. The investigation of the gain characteristic of gallium nitride (GaN) RFPA has shown an important RFPA attribute where the gain varied substantially as the drain voltage increases. By using the AET technique, the gain characteristic is harnessed to get linearity improvement. In order to validate the technique, AET measurement systems for two-carrier and WCDMA signals were developed and experimented. A special Class AB RFPA is designed and implemented to use dedicatedly for this investigation. In two-carrier signal measurement, a tracking generator is developed that consists of an envelope amplifier (EA) and a diplexer. The RFPA and the tracking generator are then combined to be an integrated AET block. In order to accommodate the high peak-toaverage ratio (PAR) and high bandwidth WCDMA signal, a broadband RF transformer was designed as part of the AET tracking generator to replace the diplexer. The two-carrier and WCDMA signals measurement results have proven that the AET technique is a valid technique for efficiency and linearity improvement. The improvements were achieved with simple, compact and cost-effective implementation

On the design of high-efficiency RF Doherty power amplifiers

Power amplifiers (PAs) are one of the most crucial elements in wireless standards becasue they are the most power hungry subsystems. These elements have to face an important issue, which is the power efficiency, a fact related with the output back-off (OBO). But the OBO depends on the kind of modulated signal, in proportion to the modulated signal peak-to-average power ratio (PAPR). The higuer is the data rate, the higer is the OBO, and consequently the lower is the efficiency. A low efficiency of PAs causes the waste of energy as heat. Furthermore, the trade-off between linearity and efficiency in PAs is another major issue. To cope with the undesired circumstances producing efficiency degradation, the Doherty power amplifier (DPA) is one of the useful techniques which provide high efficiency for high PAPR of modern communication signals. Nevertheless, the limited bandwidth (BW) of this kind of PAs (about 10% of fractional bandwidth) and its importance (in modern wireless systems such as LTE, WiMAX, Wi-Fi and satellite systems) have encouraged the researchers to improve this drawback in recent years. Some typical BW limiting factors effect on the performance of DPAs: i) quarter-wave length transformers, ii) phase compensation networks in/output matching circuits, iii) offset lines and device non-idealities; The quarter-wave length transformers performs as an inverter impedance in the load modulation technique of DPAs. The future objective in designing DPAs is to decrease the impact of these issues. In this context, this PhD-thesis is focused on improving fractional bandwidth of DPAs using the new methods that are related to impedance transformers instead of impedance inverters in the load modulation technique. This study is twofold. First, it is presented a novel DPA where a wideband GaN DPA in the 2.5 GHz band with an asymmetrical Wilkinson splitter. The impedance transformer of the proposed architecture is based on a matching network including a tapered line with multi-section transformer in the main stage. The BW of this DPA has ranged from 1.8 to 2.7 GHz. Plus, the obtained power efficiency (drain) is higher than 33% in the whole BW at both maximum and OBO power levels. Second, based on the benefits of the Klopfenstein taper, a promising DPA design is proposed where a Klopfenstein taper replaces the tapered line. In fact, this substitution results on reducing the reflection coefficient of the transformer. From a practical prototype realization of this novel Doherty-like PA in the 2.25 GHz band, this modification has demonstrated that the resulting DPA BW is increased in comparison to the conventional topology while keeping the efficiency figures. Moreover, this study also shows that the Klopfenstein taper based design allows an easy tuning of the group delay through the output reactance of the taper, resulting in a more straightforward adjustments than other recently published designs where the quarter-wave transformer is replaced by multi-section transmission lines (hybrid or similar). Experimental results have shown 43-54% of drain efficiency at 42 dBm output power, in the range of 1.7 to 2.75 GHz. Concretely, the results presented in this novel Doherty-like PA implies an specific load modulation technique that uses the mixed Klopfenstein tapered line together with a multi-section transformer in order to obtain high bandwidth with the usual efficiency in DPAs.Los amplificadores de potencia (PAs) son uno de los elementos más importantes para los transmisores inalámbricos desde el punto de vista del consumo energético. Un aspecto muy importante es su eficiencia energética, un concepto relacionado con el back-off de salida (OBO), que a su vez viene condicionadpo por el PAPR de la señal modulada a amplificar. Una baja eficiencia de los PA hace que la pérdida de energía se manifieste en forma de calor. De hecho, esta cuestión conduce al incremento de los costes y tamaño, esto último por los radiadores. Además, el compromiso entre la linealidad y la eficiencia en los PA es otro problema importante. Para hacer frente a las circunstancias que producen la degradación de la eficiencia, el amplificador de potencia tipo Doherty (DPA) es una de las técnicas más útiles que proporcionan una buena eficiencia incluso para los altos PAPR comunes en señales de comunicación modernos. Sin embargo, el limitado ancho de banda (BW) de este tipo de PA (alrededor del 10% del ancho de banda fraccional) y su importancia (en los sistemas inalámbricos modernos, tales como LTE, WiMAX, Wi-Fi y sistemas de satélites) han animado a los investigadores para mejorar este inconveniente en los últimos años. Algunos aspectos típicos que limitan el BW en los DPA son: i) transformadores de longitud de cuarto de onda, ii) redes de compensación de fase y circuitos de adaptación de salida, iii) compensación de las líneas y los dispositivos no ideales. Los transformadores de cuarto de onda actuan como un inversor de impedancia en la técnica de modulación de carga de la DPA "("load modulation"). Concretamente, el objetivo futuro de diseño de DPA es disminuir el impacto de estos problemas. En este contexto, esta tesis doctoral se centra en mejorar el ancho de banda fraccional de DPA utilizando los nuevos métodos que están relacionados con el uso de transformadores de impedancias en vez de inversores en el subcircuito de modulación de carga. Este estudio tiene dos niveles. En primer lugar, se presenta una novedosa estructura del DPA de banda ancha usándose dispositivos de GaN en la banda de 2,5 GHz con un divisor Wilkinson asimétrico. El transformador de impedancias de la arquitectura propuesta se basa en una red de adaptación, incluyendo una línea cónica con múltiples secciones del transformador en la etapa principal. El BW de este DPA ha sido de 1,8 a 2,7 GHz. Además, se obtiene una eficiencia de drenador de más del 33% en todo el BW, tanto a nivel de potencia máxima como a nivel del OBO. En segundo lugar, aprovechando los beneficios de un adaptador de Klopfenstein, se propone un nuevo diseño del DPA. Con la sustitución de la lina conica por el Klopfenstein se reduce el coeficiente de reflexión de transformador de impedancias. Sobre un prototipo práctico de esta nueva estructura del Doherty, en la banda de 2,25 GHz, se ha demostrado que el BW resultante se incrementa en comparación con la topología convencional mientras se mantienen las cifras de eficiencia. Por otra parte, en este estudio se demuestra que el diseño basado en el Klopfenstein permite una afinación fácil del retardo de grupo a través de la reactancia de salida del taper, lo que resulta en un ajuste más sencillo que otros diseños publicados recientemente en el que el transformador de cuarto de onda se sustituye por multi-líneas de transmisión de la sección (híbridos o similar). Los resultados experimentales han mostrado un 43-54% de eficiencia de drenador sobre 42 dBm de potencia de salida, en el intervalo de 1,7 a 2,75 GHz. Concretamente, los resultados presentados en esta nueva estructura tipo-Doherty implican una técnica de modulación de carga que utiliza una combinación de un Klopfenstein junto con un transformador de múltiples secciones con el fin de obtener un alto ancho de banda con la eficiencia habitual en DPAs.Els amplificadors de potència (PA) són un dels elements més importants per els sistemes ràdio ja que sone ls principals consumidors d'energía. Un aspecte molt important és l'eficiència de l'amplificador, aspecte relacionat amb el back-off de sortida (OBO) que a la seva vegada ve condicionat pel PAPR del senyal modulat. Una baixa eficiència dels PA fa que la pèrdua d'energia en manifesti en forma de calor. De fet, aquesta qüestió porta a l'increment dels costos i grandària, degut als dissipadors de calor. A més, el compromís entre la linealitat i l'eficiència en els PA es un altre problema important. Per fer front a les circumstàncies que porten a la degradació de l'eficiència, l'amplificador de potència Doherty (DPA) és una de les tècniques més útils i que proporcionen una bona eficiència per als alts PAPR comuns en senyals de comunicació moderns. No obstant això, l'ample de banda limitat (BW) d'aquest tipus de PA (al voltant del 10% de l'ample de banda fraccional) i la seva importància (en els sistemes moderns, com ara LTE, WiMAX, Wi-Fi i sistemes de satèl·lits) han animat els investigadors per millorar aquest inconvenient en els últims anys. Alguns aspectes tipicament limitadors del BW en els DPA son: i) transformadors de longitud d'quart d'ona, ii) xarxes de compensació de fase en circuits / adaptacions de sortida, iii) compensació de les línies i els dispositius no ideals. Els transformadors de quart d'ona s'utilitzen com a inversors d'impedàncies en la tècnica de modulació de càrrega del DPA ("load modulation"). Concretament, l'objectiu futur de disseny d'DPA és disminuir l'impacte d'aquests problemes. En aquest context, aquesta tesi doctoral es centra en millorar l'ample de banda fraccional dels DPA utilitzant nous mètodes que estan relacionats amb l'ús de transformadors d'impedàncies, en comptes d'inversors, en el subcircuit de modulació de càrrega. Aquest treball té dos nivells. En primer lloc, es presenta un DPA novedós que fa servir dispositus GaN DPA a la banda de 2,5 GHz amb un divisor Wilkinson asimètric. El transformador d'impedàncies de l'arquitectura proposada es basa en una xarxa d'adaptació, incloent una línia cònica amb múltiples seccions del transformador en l'etapa principal. El BW d'aquest DPA ha mostrat ser d'1,8 a a 2,7 GHz. A més, s'obté una eficiència de drenador de més del 33% en tot el BW, tant a nivell de potència màxima com de OBO. En segon lloc, sobre la base dels beneficis del adaptador de Klopfenstein, un proposa un nou disseny on un Klopfenstein substitueix la anterior línia cònica. Aquesta substitució repercuteix en la reducció del coeficient de reflexió de transformador d'impedàncies.Des d'una realització pràctica (prototipus) d'aquest nou amplificador tipus Doherty a la banda de 2,25 GHz, s'ha demostrat que el BW resultant s'incrementa en comparació amb la topologia convencional mentre es mantenen les xifres d'eficiència. D'altra banda, en aquest estudi es demostra que el disseny basat en el Klopfenstein permet una afinació fàcil del retard de grup a través de la reactància de sortida de la forma cònica, el que resulta en un ajust més senzill que altres dissenys publicats recentment en què el transformador de quart d'ona es substitueix per multi-línies de transmissió de la secció (híbrids o similar). Els resultats experimentals han mostrat un 43-54% d'eficiència de drenador en 42 dBm de potència de sortida, en l'interval de 1,7-2,75 GHz. Concretament, els resultats presentats en aquest nou amplificador tipus Doherty impliquen una tècnica de modulació de càrrega específic que utilitza una combinació del Klopfenstein juntament amb un transformador de múltiples seccions per tal d'obtenir un alt ample de banda amb la usual eficiència en DPAs.Postprint (published version

A Doherty Power Amplifier with Extended Bandwidth and Reconfigurable Back-off Level

Emerging wireless standards are designed to be spectrally efficient to address the high cost of licensing wireless spectra. Unfortunately, the resulting signals have a high peak-to-average ratio that reduces the base station power amplifier efficiency at the back-off power level. The wasted energy is converted to heat that degrades the device reliability and increases the base-station’s carbon footprint and cooling requirements. In addition, these new standards place stringent re- quirements on the amplifier output power, linearity, efficiency, and bandwidth. To improve the back-off efficiency, a Doherty amplifier, which uses two device in parallel for back-off efficiency enhancement, is deployed in a typical base station. Unfortunately, the conventional Doherty amplifier is narrowband and thus cannot satisfy the bandwidth requirement of the modern base station that needs to support multiple standards and backward compatibility. In this thesis, we begin by studying the class F/F−1 high efficiency mode of operation. To this end, we designed a narrowband, harmonically-tuned 3.3 GHz, 10 W GaN high efficiency amplifier. Next, we investigate how to simultaneously achieve high efficiency and broad bandwidth by harnessing the simplified real frequency technique for the broadband matching network design. A 2 to 3 GHz, 45 W GaN amplifier and a 650 to 1050 MHz, 45 W LDMOS amplifier were designed. Finally, we analyze the conventional Doherty amplifier to determine the cause of its narrow bandwidth. We find that the narrow bandwidth can be attributed to the band-limited quarter-wave transformer as well as the widely adopted traditional design technique. As an original contribution to knowledge, we propose a novel Doherty amplifier configuration with intrinsically broadband characteristics by analyzing the load modulation concept and the conventional Doherty amplifier. The proposed amplifier uses asymmetrical drain voltage biases and symmetrical devices and it does not require a complex mixed-signal setup. To demonstrate the proposed concept in practice, we designed a 700 to 1000 MHz, 90 W GaN broadband Doherty amplifier. Moreover, to show that the proposed concept is applicable to high power designs, we designed a 200 W GaN broadband Doherty amplifier in the same band. In addition, to show that the technique is independent of the device technology, we designed a 700 to 900 MHz, 60 W LDMOS broadband Doherty amplifier. Using digital pre-distortion, the three prototypes were shown to be highly linearizable when driven with wideband 20 MHz LTE and WCDMA modulated signals and achieved excellent back-off efficiency. Lastly, using the insights from the previous analyses, we propose a novel mixed-technology Doherty amplifier with an extended and reconfigurable back-off level as well as an improved power utilization factor. The reconfigurability of the proposed amplifier makes it possible to customize the back-off level to achieve the highest average efficiency for a given modulated signal without redesigning the matching networks. A 790 to 960 MHz, 180 W LDMOS/GaN Doherty amplifier demonstrated the extended bandwidth and reconfigurability of the back-off level. The proposed amplifier addresses the shortcomings of the conventional Doherty amplifier and satisfies the many requirements of a modern base station power amplifier

Broadband Doherty Power Amplifiers with Enhanced Linearity for Emerging Radio Transmitters

The ever-increasing demand for utilizing wireless spectra has led to development of spectrally efficient radio systems. While these systems offer much higher data throughput, they employ more sophisticated modulation schemes, which result in wideband signals with high peak-to-average power ratios. These signal characteristics significantly complicate the design of RF transmitters, particularly power amplifiers, in terms of power efficiency and linearity requirements. Furthermore, upcoming wireless standards, such as long term evolution advanced (LTE-A) require adoption of carrier aggregation which incorporates multiple component carriers to yield aggregated channels of larger bandwidth (up to 100 MHz). On the other hand, the emerging systems are expected to support legacy standards with minimum area, cost, and power overhead, and thus call for highly-efficient linear broadband power amplifiers capable of efficiently amplifying concurrent modulated signals located over a broad carrier frequency range. This thesis focuses on Doherty power amplifiers (DPAs) with extended high-efficiency range, enhanced bandwidth and improved linearity as a solution for high-efficiency multi-band multi-standard transmitters. It addresses three major concerns associated with DPAs, namely, back-off efficiency, bandwidth, and linearity. The Thesis begins with a detailed theoretical analysis of two-way and three-way Doherty configurations from which the governing equations are derived. This is followed by a comprehensive study of bandwidth limitation in DPA variants. As the first contribution, it is shown that the two existing three-way Doherty structures, i.e., conventional and modified DPAs have inherently broadband characteristics and thus are promising solutions for multi-standard base station transmitters. As a proof of concept, a 30-W three-way modified Doherty amplifier was designed and implemented using packaged GaN transistors over 0.73-0.98 GHz. The prototype was successfully linearized under modulated signals with up to 20 MHz modulation bandwidth. To further improve the linearizability of the DPAs under wideband and multi-band modulated signals, this thesis investigates major sources of static and dynamic nonlinearity in two-way DPAs both at device and circuit levels and explores circuit techniques to mitigate them. Furthermore, the challenges of applying the Doherty technique for concurrent transmission of multiple modulated signals are tackled. The most significant contribution of this thesis is to develop a novel waveform engineering approach to designing ultrawideband DPAs. This approach completely reformulates the DPA's output combiner conditions in order to accommodate complex-valued load modulation. Moreover, it relaxes the harmonic termination requirements of the DPAs to further enlarge the Doherty design space, thereby enhancing the bandwidth. A 50-W waveform-engineered two-way DPA prototype was designed for 1.5-2.5 GHz range and was successfully linearized under intra- and inter-band carrier-aggregated signals with up to 600 MHz carrier spacing. Lastly, an input matching network design methodology is proposed for broadband DPAs. This methodology uses the novel concept of ``current contours'' to minimize the bandwidth, efficiency and linearity degradation of DPAs caused by device input non-idealities