Synthesis of Clock Trees with Useful Skew based on Sparse-Graph Algorithms

Computer-aided design (CAD) for very large scale integration (VLSI) involve

Clock Polarity Assignment Methodologies for Designing High-Performance and Robust Clock Trees

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2016. 8. 김태환.In modern synchronous circuits, the system relies on one single signal, namely, the clock signal. All data sampling of flip-flops rely on the timing of the clock signal. This makes clock trees, which deliver the clock signal to every clock sink in the whole system, one of the most active components on a chip, as it must switch without halting. Naturally, this makes clock trees a primary target of optimization for low power/high performance designs. First, bounded skew clock polarity assignment is explored. Buffers in the clock tree switch simultaneously as the clock signal switch, which causes power/ground supply voltage fluctuation. This phenomenon is referred to as clock noise and brings adverse effects on circuit robustness. Clock polarity assignment technique replaces some of the buffers in the clock trees with inverters. Since buffers draw larger current at the rising edge of the clock while inverters draw larger current at the falling edge, this technique can mitigate peak noise problem at the power/ground supply rails. Second, useful skew clock polarity assignment method is developed. Useful clock skew methodology allows consideration of individual clock skew restraints between each clock sinks, allowing further noise reduction by exploiting more time slack. Through experiments with ISPD 2010 clock network synthesis contest benchmark circuits, the results show that the proposed clock polarity algorithm is able to reduce the peak noise caused by clock buffers by 10.9% further over that of the global skew bound constrained polarity assignment while satisfying all setup and hold time constraints. Lastly, as multi-corner multi-mode (MCMM) design methodologies, process variations and clock gating techniques are becoming common place in advanced technology nodes, clock polarity assignment methods that mitigate these problems are devised. Experimental results indicate that the proposed methods successfully satisfy required design constraints imposed by such variations. In summary, this dissertation presents clock polarity assignments that considers useful clock skew, delay variations, MCMM design methodologies and clock gating techniques.Chapter 1 Introduction 1 1.1 Clock Trees 1 1.2 Simultaneous Switching Noise 3 1.3 Clock Polarity Assignment Technique 4 1.4 Contributions of this Dissertation 5 Chapter 2 Clock Polarity Assignment Under Bounded Skew 7 2.1 Introduction 7 2.2 Motivational Example 9 2.3 Problem Formulation 13 2.4 Proposed Algorithm 17 2.4.1 Independence Assumption 17 2.4.2 Characterization of Noise 18 2.4.3 Overview of the Proposed Algorithm 19 2.4.4 Mapping WaveMin Problem to MOSP problem 22 2.4.5 A Fast Algorithm 26 2.4.6 Zone Sizing/Partitioning Method 27 2.5 Experimental Results 28 2.5.1 Experimental Setup 28 2.5.2 Noise Reduction 28 2.5.3 Simulation on Full Circuit 29 2.6 Effects of Clock Polarity Assignment on Simultaneous Switching Noise 34 2.6.1 Model of Power Delivery Network 34 2.6.2 Peak-to-Peak Voltage Swing 35 2.7 Effects of Decoupling Capacitors 36 2.8 Effects of Clock Polarity Assignment on Clock Jitter 40 2.8.1 Noise in Frequency Domain 40 2.9 Summary 43 Chapter 3 Clock Polarity Assignment Under Useful Skew 44 3.1 Introduction 44 3.2 Motivational Example 45 3.3 Problem Formulation 47 3.4 Proposed Algorithm 49 3.4.1 Integer Linear Programming Formulation and Linear Programming Relaxation 49 3.4.2 Formulating into Maximum Clique Problem 49 3.4.3 Scalable Algorithm for Clique Exploration 51 3.5 Experimental Results 54 3.5.1 Experimental Setup 54 3.5.2 Assessing the Performance of UsefulMin over Wavemin 56 3.6 Summary 57 Chapter 4 Extensions of Clock Polarity Assignment Methods 60 4.1 Coping With Thermal Variations 60 4.1.1 Introduction 60 4.1.2 Proposed Method 61 4.1.3 Experimental Results 66 4.2 Coping with Delay Variations 70 4.2.1 Introduction 70 4.2.2 The Impact of Process Variations on Polarity Assignment 71 4.2.3 Proposed Method for Variation Resiliency 72 4.2.4 Experimental Results 73 4.3 Coping With Multi-Mode Designs 75 4.3.1 Introduction 75 4.3.2 Proposed Method 76 4.3.3 Experimental Results 84 4.4 Orthogonality with Other Design Techniques ? Clock Gating 87 4.4.1 Introduction 87 4.4.2 Proposed Partitioning Method 87 4.4.3 Experimental Results 88 4.5 Summary 90 Chapter 5 Conclusion 92 5.1 Clock Polarity Assignment Under Bounded Skew 92 5.2 Clock Polarity Assignment Under Useful Skew 93 5.3 Extensions of Clock Polarity Assignment 93 Appendices 94 Chapter A Power Spectral Densities of ISCAS89 Circuits 95 Chapter B The Effect of Decoupling Capacitors 99 초록 109Docto

로직 및 피지컬 합성에서의 타이밍 분석과 최적화

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2020. 8. 김태환.Timing analysis is one of the necessary steps in the development of a semiconductor circuit. In addition, it is increasingly important in the advanced process technologies due to various factors, including the increase of process–voltage–temperature variation. This dissertation addresses three problems related to timing analysis and optimization in logic and physical synthesis. Firstly, most static timing analysis today are based on conventional fixed flip-flop timing models, in which every flip-flop is assumed to have a fixed clock-to-Q delay. However, setup and hold skews affect the clock-to-Q delay in reality. In this dissertation, I propose a mathematical formulation to solve the problem and apply it to the clock skew scheduling problems as well as to the analysis of a given circuit, with a scalable speedup technique. Secondly, near-threshold computing is one of the promising concepts for energy-efficient operation of VLSI systems, but wide performance variation and nonlinearity to process variations block the proliferation. To cope with this, I propose a holistic hardware performance monitoring methodology for accurate timing prediction in a near-threshold voltage regime and advanced process technology. Lastly, an asynchronous circuit is one of the alternatives to the conventional synchronous style, and asynchronous pipeline circuit especially attractive because of its small design effort. This dissertation addresses the synthesis problem of lightening two-phase bundled-data asynchronous pipeline controllers, in which delay buffers are essential for guaranteeing the correct handshaking operation but incurs considerable area increase.타이밍 분석은 반도체 회로 개발 필수 과정 중 하나로, 최신 공정일수록 공정-전압-온도 변이 증가를 포함한 다양한 요인으로 하여금 그 중요성이 커지고 있다. 본 논문에서는 로직 및 피지컬 합성과 관련하여 세 가지 타이밍 분석 및 최적화 문제에 대해 다룬다. 첫째로, 오늘날 대부분의 정적 타이밍 분석은 모든 플립-플롭의 클럭-출력 딜레이가 고정된 값이라는 가정을 바탕으로 이루어졌다. 하지만 실제 클럭-출력 딜레이는 해당 플립-플롭의 셋업 및 홀드 스큐에 영향을 받는다. 본 논문에서는 이러한 특성을 수학적으로 정리하였으며, 이를 확장 가능한 속도 향상 기법과 더불어 주어진 회로의 타이밍 분석 및 클럭 스큐 스케쥴링 문제에 적용하였다. 둘째로, 유사 문턱 연산은 초고집적 회로 동작의 에너지 효율을 끌어 올릴 수 있다는 점에서 각광받지만, 큰 폭의 성능 변이 및 비선형성 때문에 널리 활용되고 있지 않다. 이를 해결하기 위해 유사 문턱 전압 영역 및 최신 공정 노드에서 보다 정확한 타이밍 예측을 위한 하드웨어 성능 모니터링 방법론 전반을 제안하였다. 마지막으로, 비동기 회로는 기존 동기 회로의 대안 중 하나로, 그 중에서도 비동기 파이프라인 회로는 비교적 적은 설계 노력만으로도 구현 가능하다는 장점이 있다. 본 논문에서는 2위상 묶음 데이터 프로토콜 기반 비동기 파이프라인 컨트롤러 상에서, 정확한 핸드셰이킹 통신을 위해 삽입된 딜레이 버퍼에 의한 면적 증가를 완화할 수 있는 합성 기법을 제시하였다.1 INTRODUCTION 1 1.1 Flexible Flip-Flop Timing Model 1 1.2 Hardware Performance Monitoring Methodology 4 1.3 Asynchronous Pipeline Controller 10 1.4 Contributions of this Dissertation 15 2 ANALYSIS AND OPTIMIZATION CONSIDERING FLEXIBLE FLIP-FLOP TIMING MODEL 17 2.1 Preliminaries 17 2.1.1 Terminologies 17 2.1.2 Timing Analysis 20 2.1.3 Clock-to-Q Delay Surface Modeling 21 2.2 Clock-to-Q Delay Interval Analysis 22 2.2.1 Derivation 23 2.2.2 Additional Constraints 26 2.2.3 Analysis: Finding Minimum Clock Period 28 2.2.4 Optimization: Clock Skew Scheduling 30 2.2.5 Scalable Speedup Technique 33 2.3 Experimental Results 37 2.3.1 Application to Minimum Clock Period Finding 37 2.3.2 Application to Clock Skew Scheduling 39 2.3.3 Efficacy of Scalable Speedup Technique 43 2.4 Summary 44 3 HARDWARE PERFORMANCE MONITORING METHODOLOGY AT NTC AND ADVANCED TECHNOLOGY NODE 45 3.1 Overall Flow of Proposed HPM Methodology 45 3.2 Prerequisites to HPM Methodology 47 3.2.1 BEOL Process Variation Modeling 47 3.2.2 Surrogate Model Preparation 49 3.3 HPM Methodology: Design Phase 52 3.3.1 HPM2PV Model Construction 52 3.3.2 Optimization of Monitoring Circuits Configuration 54 3.3.3 PV2CPT Model Construction 58 3.4 HPM Methodology: Post-Silicon Phase 60 3.4.1 Transfer Learning in Silicon Characterization Step 60 3.4.2 Procedures in Volume Production Phase 61 3.5 Experimental Results 62 3.5.1 Experimental Setup 62 3.5.2 Exploration of Monitoring Circuits Configuration 64 3.5.3 Effectiveness of Monitoring Circuits Optimization 66 3.5.4 Considering BEOL PVs and Uncertainty Learning 68 3.5.5 Comparison among Different Prediction Flows 69 3.5.6 Effectiveness of Prediction Model Calibration 71 3.6 Summary 73 4 LIGHTENING ASYNCHRONOUS PIPELINE CONTROLLER 75 4.1 Preliminaries and State-of-the-Art Work 75 4.1.1 Bundled-data vs. Dual-rail Asynchronous Circuits 75 4.1.2 Two-phase vs. Four-phase Bundled-data Protocol 76 4.1.3 Conventional State-of-the-Art Pipeline Controller Template 77 4.2 Delay Path Sharing for Lightening Pipeline Controller Template 78 4.2.1 Synthesizing Sharable Delay Paths 78 4.2.2 Validating Logical Correctness for Sharable Delay Paths 80 4.2.3 Reformulating Timing Constraints of Controller Template 81 4.2.4 Minimally Allocating Delay Buffers 87 4.3 In-depth Pipeline Controller Template Synthesis with Delay Path Reusing 88 4.3.1 Synthesizing Delay Path Units 88 4.3.2 Validating Logical Correctness of Delay Path Units 89 4.3.3 Updating Timing Constraints for Delay Path Units 91 4.3.4 In-depth Synthesis Flow Utilizing Delay Path Units 95 4.4 Experimental Results 99 4.4.1 Environment Setup 99 4.4.2 Piecewise Linear Modeling of Delay Path Unit Area 99 4.4.3 Comparison of Power, Performance, and Area 102 4.5 Summary 107 5 CONCLUSION 109 5.1 Chapter 2 109 5.2 Chapter 3 110 5.3 Chapter 4 110 Abstract (In Korean) 127Docto

Energy-Efficient Digital Circuit Design using Threshold Logic Gates

abstract: Improving energy efficiency has always been the prime objective of the custom and automated digital circuit design techniques. As a result, a multitude of methods to reduce power without sacrificing performance have been proposed. However, as the field of design automation has matured over the last few decades, there have been no new automated design techniques, that can provide considerable improvements in circuit power, leakage and area. Although emerging nano-devices are expected to replace the existing MOSFET devices, they are far from being as mature as semiconductor devices and their full potential and promises are many years away from being practical. The research described in this dissertation consists of four main parts. First is a new circuit architecture of a differential threshold logic flipflop called PNAND. The PNAND gate is an edge-triggered multi-input sequential cell whose next state function is a threshold function of its inputs. Second a new approach, called hybridization, that replaces flipflops and parts of their logic cones with PNAND cells is described. The resulting \hybrid circuit, which consists of conventional logic cells and PNANDs, is shown to have significantly less power consumption, smaller area, less standby power and less power variation. Third, a new architecture of a field programmable array, called field programmable threshold logic array (FPTLA), in which the standard lookup table (LUT) is replaced by a PNAND is described. The FPTLA is shown to have as much as 50% lower energy-delay product compared to conventional FPGA using well known FPGA modeling tool called VPR. Fourth, a novel clock skewing technique that makes use of the completion detection feature of the differential mode flipflops is described. This clock skewing method improves the area and power of the ASIC circuits by increasing slack on timing paths. An additional advantage of this method is the elimination of hold time violation on given short paths. Several circuit design methodologies such as retiming and asynchronous circuit design can use the proposed threshold logic gate effectively. Therefore, the use of threshold logic flipflops in conventional design methodologies opens new avenues of research towards more energy-efficient circuits.Dissertation/ThesisDoctoral Dissertation Computer Science 201

High-speed, economical design implementation of transit network router

Thesis (M.S.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 1995.Includes bibliographical references (p. 88-90).by Kazuhiro Hara.M.S

Power efficient resilient microarchitectures for PVT variability mitigation

Nowadays, the high power density and the process, voltage, and temperature variations became the most critical issues that limit the performance of the digital integrated circuits because of the continuous scaling of the fabrication technology. Dynamic voltage and frequency scaling technique is used to reduce the power consumption while different time relaxation techniques and error recovery microarchitectures are used to tolerate the process, voltage, and temperature variations. These techniques reduce the throughput by scaling down the frequency or flushing and restarting the errant pipeline. This thesis presents a novel resilient microarchitecture which is called ERSUT-based resilient microarchitecture to tolerate the induced delays generated by the voltage scaling or the process, voltage, and temperature variations. The resilient microarchitecture detects and recovers the induced errors without flushing the pipeline and without scaling down the operating frequency. An ERSUT-based resilient 16 × 16 bit MAC unit, implemented using Global Foundries 65 nm technology and ARM standard cells library, is introduced as a case study with 18.26% area overhead and up to 1.5x speedup. At the typical conditions, the maximum frequency of the conventional MAC unit is about 375 MHz while the resilient MAC unit operates correctly at a frequency up to 565 MHz. In case of variations, the resilient MAC unit tolerates induced delays up to 50% of the clock period while keeping its throughput equal to the conventional MAC unit’s maximum throughput. At 375 MHz, the resilient MAC unit is able to scale down the supply voltage from 1.2 V to 1.0 V saving about 29% of the power consumed by the conventional MAC unit. A double-edge-triggered microarchitecture is also introduced to reduce the power consumption extremely by reducing the frequency of the clock tree to the half while preserving the same maximum throughput. This microarchitecture is applied to different ISCAS’89 benchmark circuits in addition to the 16x16 bit MAC unit and the average power reduction of all these circuits is 63.58% while the average area overhead is 31.02%. All these circuits are designed using Global Foundries 65nm technology and ARM standard cells library. Towards the full automation of the ERSUT-based resilient microarchitecture, an ERSUT-based algorithm is introduced in C++ to accelerate the design process of the ERSUT-based microarchitecture. The developed algorithm reduces the design-time efforts dramatically and allows the ERSUT-based microarchitecture to be adopted by larger industrial designs. Depending on the ERSUT-based algorithm, a validation study about applying the ERSUT-based microarchitecture on the MAC unit and different ISCAS’89 benchmark circuits with different complexity weights is introduced. This study shows that 72% of these circuits tolerates more than 14% of their clock periods and 54.5% of these circuits tolerates more than 20% while 27% of these circuits tolerates more than 30%. Consequently, the validation study proves that the ERSUT-based resilient microarchitecture is a valid applicable solution for different circuits with different complexity weights

Clock Generator Circuits for Low-Power Heterogeneous Multiprocessor Systems-on-Chip

In this work concepts and circuits for local clock generation in low-power heterogeneous multiprocessor systems-on-chip (MPSoCs) are researched and developed. The targeted systems feature a globally asynchronous locally synchronous (GALS) clocking architecture and advanced power management functionality, as for example fine-grained ultra-fast dynamic voltage and frequency scaling (DVFS). To enable this functionality compact clock generators with low chip area, low power consumption, wide output frequency range and the capability for ultra-fast frequency changes are required. They are to be instantiated individually per core. For this purpose compact all digital phase-locked loop (ADPLL) frequency synthesizers are developed. The bang-bang ADPLL architecture is analyzed using a numerical system model and optimized for low jitter accumulation. A 65nm CMOS ADPLL is implemented, featuring a novel active current bias circuit which compensates the supply voltage and temperature sensitivity of the digitally controlled oscillator (DCO) for reduced digital tuning effort. Additionally, a 28nm ADPLL with a new ultra-fast lock-in scheme based on single-shot phase synchronization is proposed. The core clock is generated by an open-loop method using phase-switching between multi-phase DCO clocks at a fixed frequency. This allows instantaneous core frequency changes for ultra-fast DVFS without re-locking the closed loop ADPLL. The sensitivity of the open-loop clock generator with respect to phase mismatch is analyzed analytically and a compensation technique by cross-coupled inverter buffers is proposed. The clock generators show small area (0.0097mm2 (65nm), 0.00234mm2 (28nm)), low power consumption (2.7mW (65nm), 0.64mW (28nm)) and they provide core clock frequencies from 83MHz to 666MHz which can be changed instantaneously. The jitter performance is compliant to DDR2/DDR3 memory interface specifications. Additionally, high-speed clocks for novel serial on-chip data transceivers are generated. The ADPLL circuits have been verified successfully by 3 testchip implementations. They enable efficient realization of future low-power MPSoCs with advanced power management functionality in deep-submicron CMOS technologies.In dieser Arbeit werden Konzepte und Schaltungen zur lokalen Takterzeugung in heterogenen Multiprozessorsystemen (MPSoCs) mit geringer Verlustleistung erforscht und entwickelt. Diese Systeme besitzen eine global-asynchrone lokal-synchrone Architektur sowie Funktionalität zum Power Management, wie z.B. das feingranulare, schnelle Skalieren von Spannung und Taktfrequenz (DVFS). Um diese Funktionalität zu realisieren werden kompakte Taktgeneratoren benötigt, welche eine kleine Chipfläche einnehmen, wenig Verlustleitung aufnehmen, einen weiten Bereich an Ausgangsfrequenzen erzeugen und diese sehr schnell ändern können. Sie sollen individuell pro Prozessorkern integriert werden. Dazu werden kompakte volldigitale Phasenregelkreise (ADPLLs) entwickelt, wobei eine bang-bang ADPLL Architektur numerisch modelliert und für kleine Jitterakkumulation optimiert wird. Es wird eine 65nm CMOS ADPLL implementiert, welche eine neuartige Kompensationsschlatung für den digital gesteuerten Oszillator (DCO) zur Verringerung der Sensitivität bezüglich Versorgungsspannung und Temperatur beinhaltet. Zusätzlich wird eine 28nm CMOS ADPLL mit einer neuen Technik zum schnellen Einschwingen unter Nutzung eines Phasensynchronisierers realisiert. Der Prozessortakt wird durch ein neuartiges Phasenmultiplex- und Frequenzteilerverfahren erzeugt, welches es ermöglicht die Taktfrequenz sofort zu ändern um schnelles DVFS zu realisieren. Die Sensitivität dieses Frequenzgenerators bezüglich Phasen-Mismatch wird theoretisch analysiert und durch Verwendung von kreuzgekoppelten Taktverstärkern kompensiert. Die hier entwickelten Taktgeneratoren haben eine kleine Chipfläche (0.0097mm2 (65nm), 0.00234mm2 (28nm)) und Leistungsaufnahme (2.7mW (65nm), 0.64mW (28nm)). Sie stellen Frequenzen von 83MHz bis 666MHz bereit, welche sofort geändert werden können. Die Schaltungen erfüllen die Jitterspezifikationen von DDR2/DDR3 Speicherinterfaces. Zusätzliche können schnelle Takte für neuartige serielle on-Chip Verbindungen erzeugt werden. Die ADPLL Schaltungen wurden erfolgreich in 3 Testchips erprobt. Sie ermöglichen die effiziente Realisierung von zukünftigen MPSoCs mit Power Management in modernsten CMOS Technologien

Proceedings of the 5th International Workshop on Reconfigurable Communication-centric Systems on Chip 2010 - ReCoSoC\u2710 - May 17-19, 2010 Karlsruhe, Germany. (KIT Scientific Reports ; 7551)

ReCoSoC is intended to be a periodic annual meeting to expose and discuss gathered expertise as well as state of the art research around SoC related topics through plenary invited papers and posters. The workshop aims to provide a prospective view of tomorrow\u27s challenges in the multibillion transistor era, taking into account the emerging techniques and architectures exploring the synergy between flexible on-chip communication and system reconfigurability