1,329 research outputs found
High Linearity SAR ADC for Smart Sensor Applications
This paper presents capacitive array optimization technique to improve the Spurious Free Dynamic Range (SFDR) and Signal-to-Noise-and-Distortion Ratio (SNDR) of Successive Approximation Register (SAR) Analog-to-Digital Converter (ADC) for smart sensor application. Monte Carlo simulation results show that capacitive array optimization technique proposed can make the SFDR, SNDR and (Signal-to-Noise Ratio) SNR more concentrated, which means the differences between maximum value and minimum value of SFDR, SNDR and SNR are much smaller than the conventional calibration techniques, more stable performance enhancement can be achieved, and the averaged SFDR is improved from 72.9 dB to 91.1 dB by using the capacitive array optimization method, 18.2 dB improvement of SFDR is obtained with only little expense of digital logic circuits, which makes it good choice for high resolution and high linearity smart sensing systems
Capacitor Mismatch Calibration Technique to Improve the SFDR of 14-Bit SAR ADC
This paper presents mismatch calibration technique to improve the SFDR in a 14-bit successive approximation register (SAR) analog-to-digital converter (ADC) for wearable electronics application. Behavioral Monte-Carlo simulations are applied to demonstrate the effect of the proposed method where no complex digital calibration algorithm or auxiliary calibration DAC needed. Simulation results show that with a mismatch error typical of modern technology, the SFDR is enhanced by more than 20 dB with the proposed technique for a 14-bit SAR ADC
Recommended from our members
Noise shaping Asynchronous SAR ADC based time to digital converter
Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin
High-Resolution ADCs Design in Image Sensors
This paper presents design considerations for high-resolution and high-linearity ADCs for biomedical imaging ap-plications. The work discusses how to improve dynamic spec-ifications such as Spurious Free Dynamic Range (SFDR) and Signal-to-Noise-and-Distortion Ratio (SNDR) in ultra-low power and high-resolution analog-to-digital converters (ADCs) including successive approximation register (SAR) for biomedical imaging application. The results show that with broad range of mismatch error, the SFDR is enhanced by about 10 dB with the proposed performance enhancement technique, which makes it suitable for high resolution image sensors sensing systems
Exploiting smallest error to calibrate non-linearity in SAR ADCs
This paper presents a statistics-optimised organisation technique to achieve better element matching in Successive Approximation Register (SAR) Analog-to-Digital Converter (ADC) in smart sensor systems. We demonstrate the proposed technique ability to achieve a significant improvement of around 23 dB on Spurious Free Dynamic Range (SFDR) of the ADC than the conventional, testing with a capacitor mismatch σu = 0.2% in a 14 bit SAR ADC system. For the static performance, the max root mean square (rms) value of differential nonlinearity (DNL) reduces from 1.63 to 0.20 LSB and the max rms value of integral nonlinearity (INL) reduces from 2.10 to 0.21 LSB. In addition, it is demonstrated that by applying grouping optimisation and strategy optimisation, the performance boosting on SFDR can be effectively achieved. Such great improvement on the resolution of the ADC only requires an off-line pre-processing digital part
A radiation-hard dual-channel 12-bit 40 MS/s ADC prototype for the ATLAS liquid argon calorimeter readout electronics upgrade at the CERN LHC
The readout electronics upgrade for the ATLAS Liquid Argon Calorimeters at
the CERN Large Hadron Collider requires a radiation-hard ADC. The design of a
radiation-hard dual-channel 12-bit 40 MS/s pipeline ADC for this use is
presented. The design consists of two pipeline A/D channels each with four
Multiplying Digital-to-Analog Converters followed by 8-bit
Successive-Approximation-Register analog-to-digital converters. The custom
design, fabricated in a commercial 130 nm CMOS process, shows a performance of
67.9 dB SNDR at 10 MHz for a single channel at 40 MS/s, with a latency of 87.5
ns (to first bit read out), while its total power consumption is 50 mW/channel.
The chip uses two power supply voltages: 1.2 and 2.5 V. The sensitivity to
single event effects during irradiation is measured and determined to meet the
system requirements
Recommended from our members
Design and implementation of Radix-3/Radix-2 based novel hybrid SAR ADC in scaled CMOS technologies
This thesis focuses on low power and high speed design techniques for successive
approximation register (SAR) analog-to-digital converters (ADCs) in nanoscale
CMOS technologies. SAR ADCs’ speed is limited by the number of bits of
resolution. An N-bit conventional SAR ADC takes N conversion cycles. To speed
up the conversion process, we introduce a radix-3 SAR ADC which can compute
1:6 bits per cycle. To our knowledge, it is the first fully programmable and efficiently
hardware controlled radix-3 SAR ADC. We had to use two comparators per
cycle due to ADC architecture and we proposed a simple calibration scheme for
the comparators. Also, as the architecture of the DAC array is completely different
from the architecture of conventional radix-2 SAR ADC’s DAC arrays, we came up
with an algorithm for calibration of capacitors of the DAC.
Low power SAR ADCs face two major challenges especially at high resolutions:
(1) increased comparator power to suppress the noise, and (2) increased
DAC switching energy due to the large DAC size. Due to our proposed architecture,the radix-3 SAR ADC uses two comparators per cycle and two differential DACs.
To improve the comparator’s power efficiency, an efficient and low cost calibration
technique has been introduced. It allows a low power and noisy comparator to
achieve high signal-to-noise ratio (SNR).
To improve the DAC switching energy, we introduced a radix-3/radix-2
based novel hybrid SAR ADC. We use two single ended DACs for radix-3 SAR
ADC and these two single ended DACs can be used as one differential DAC for
radix-2 SAR ADC. So, overall, we only have a single DAC as conventional radix-
2 SAR ADC. In addition, a monotonic switching technique is adopted for radix-2
search to reduce the DAC capacitor size and hence, to reduce switching power. It
can reduce the total number of unit capacitors by four times. Our proposed hybrid
SAR ADC can achieve less DAC energy compared to radix-3 and radix-2 SAR
ADCs. Also, to utilize technology scaling, we used the minimum capacitor size
allowed by thermal noise limitations. To achieve high resolution, we introduced
calibration algorithm for the DAC array.
As mentioned earlier, the radix-3 SAR ADC offers higher power than conventional
radix-2 SAR ADC because of simultaneous use of two comparators. In
the proposed hybrid SAR ADC, we will be using radix-3 search for first few MSB
bits. So, the resolution required for radix-3 comparators are much larger than the
LSB value of 10-bit ADC. By implementing calibration of comparators, we can
use low power, high input referred offset and high speed comparators for radix-3
search. Radix-2 search will be used for rest of the bits and the resolution of the
radix-2 comparator has to be less than the required LSB value. So, a high power, low input referred offset and high speed comparator is used for radix-2 search.
Also, we introduced clock gating for comparators. So, radix-3 comparators will not
toggle during radix-2 search and the radix-2 comparators will be inactive during
radix-3 search. By using the aforementioned techniques, the overall comparator
power is definitely less than a radix-3 SAR ADC and comparable to a conventional
radix-2 SAR ADC.
A prototype radix-3/radix-2 based hybrid SAR ADC with the proposed
technique is designed and fabricated in 40nm CMOS technology. It achieves an
SNDR of 56.9 dB and consumes only 0.38 mW power at 30MS/s, leading to a
Walden figure of merit of 21.5 fJ/conv-step.Electrical and Computer Engineerin
A 76nW, 4kS/s 10-bit SAR ADC with offset cancellation for biomedical applications
This paper presents a 10-bit fully-differential rail-to-rail successive approximation (SAR) ADC designed for biomedical applications. The ADC, fabricated in a 180nm HV CMOS technology, features low switching energy consumption and employs a time-domain comparator which includes an offset cancellation mechanism. The power dissipated by the ADC is 76.2nW at 4kS/s and achieves 9.5 ENOB.Ministerio de Economía y Competitividad TEC2012-33634Office of Naval Research (USA) N0001414135
- …