Unifying mesh- and tree-based programmable interconnect

We examine the traditional, symmetric, Manhattan mesh design for field-programmable gate-array (FPGA) routing along with tree-of-meshes (ToM) and mesh-of-trees (MoT) based designs. All three networks can provide general routing for limited bisection designs (Rent's rule with p<1) and allow locality exploitation. They differ in their detailed topology and use of hierarchy. We show that all three have the same asymptotic wiring requirements. We bound this tightly by providing constructive mappings between routes in one network and routes in another. For example, we show that a (c,p) MoT design can be mapped to a (2c,p) linear population ToM and introduce a corner turn scheme which will make it possible to perform the reverse mapping from any (c,p) linear population ToM to a (2c,p) MoT augmented with a particular set of corner turn switches. One consequence of this latter mapping is a multilayer layout strategy for N-node, linear population ToM designs that requires only /spl Theta/(N) two-dimensional area for any p when given sufficient wiring layers. We further show upper and lower bounds for global mesh routes based on recursive bisection width and show these are within a constant factor of each other and within a constant factor of MoT and ToM layout area. In the process we identify the parameters and characteristics which make the networks different, making it clear there is a unified design continuum in which these networks are simply particular regions

Circuit design and analysis for on-FPGA communication systems

On-chip communication system has emerged as a prominently important subject in Very-Large- Scale-Integration (VLSI) design, as the trend of technology scaling favours logics more than interconnects. Interconnects often dictates the system performance, and, therefore, research for new methodologies and system architectures that deliver high-performance communication services across the chip is mandatory. The interconnect challenge is exacerbated in Field-Programmable Gate Array (FPGA), as a type of ASIC where the hardware can be programmed post-fabrication. Communication across an FPGA will be deteriorating as a result of interconnect scaling. The programmable fabrics, switches and the specific routing architecture also introduce additional latency and bandwidth degradation further hindering intra-chip communication performance. Past research efforts mainly focused on optimizing logic elements and functional units in FPGAs. Communication with programmable interconnect received little attention and is inadequately understood. This thesis is among the first to research on-chip communication systems that are built on top of programmable fabrics and proposes methodologies to maximize the interconnect throughput performance. There are three major contributions in this thesis: (i) an analysis of on-chip interconnect fringing, which degrades the bandwidth of communication channels due to routing congestions in reconfigurable architectures; (ii) a new analogue wave signalling scheme that significantly improves the interconnect throughput by exploiting the fundamental electrical characteristics of the reconfigurable interconnect structures. This new scheme can potentially mitigate the interconnect scaling challenges. (iii) a novel Dynamic Programming (DP)-network to provide adaptive routing in network-on-chip (NoC) systems. The DP-network architecture performs runtime optimization for route planning and dynamic routing which, effectively utilizes the in-silicon bandwidth. This thesis explores a new horizon in reconfigurable system design, in which new methodologies and concepts are proposed to enhance the on-FPGA communication throughput performance that is of vital importance in new technology processes

Mocarabe: High-Performance Time-Multiplexed Overlays for FPGAs

Coarse-grained reconfigurable array (CGRA) overlays can improve dataflow kernel throughput by an order of magnitude over Vivado HLS on Xilinx Alveo U280. This is possible with a combination of carefully floorplanned high-frequency (645 - 768 MHz Torus, 788 - 856 MHz Mesh, 583 - 746 MHz BFT) design and a scalable, communication-aware compiler. Our CGRA architecture supports configurable Processing Element (PE) functionality supported by a configurable number of communication channels to match application demands. Compared to recent FPGA overlays like 4×4 ADRES and HyCUBE implementations in CGRA-ME, our design operates at a faster clock frequency by up to 3.4×, while scaling to an orders-of-magnitude larger array size of 19×69 on Xilinx Alveo U280. We propose a novel topology agnostic ILP placer that formulates the CGRA placement problem into an ILP problem. Our ILP placer optimizes placement regardless of topology and even for non-linear objective functions by using pre-computed placement costs as inputs to the ILP problem formulation. Using the ILP placer reduces placement quadratic wirelength up to 37% compared to the commonly used simulated annealing approach but increases runtime from less than a minute to hours. Our communication-aware compiler targets HLS objectives such as initiation interval (II) and minimizes communication cost using an integer linear programming (ILP) formulation. Unlike SDC schedulers in FPGA HLS tools, we treat data movement as a first-class citizen by encoding the space and time resources of the communication network in the ILP formulation. Given the same constraints on operational resources as Vivado HLS, we can retain our target II and achieve up to 9.2× higher frequency. We compare Torus and Mesh topologies, and show Mesh has less latency per area compared to Torus for the same benchmarks

A Hybrid Partially Reconfigurable Overlay Supporting Just-In-Time Assembly of Custom Accelerators on FPGAs

The state of the art in design and development flows for FPGAs are not sufficiently mature to allow programmers to implement their applications through traditional software development flows. The stipulation of synthesis as well as the requirement of background knowledge on the FPGAs\u27 low-level physical hardware structure are major challenges that prevent programmers from using FPGAs. The reconfigurable computing community is seeking solutions to raise the level of design abstraction at which programmers must operate, and move the synthesis process out of the programmers\u27 path through the use of overlays. A recent approach, Just-In-Time Assembly (JITA), was proposed that enables hardware accelerators to be assembled at runtime, all from within a traditional software compilation flow. The JITA approach presents a promising path to constructing hardware designs on FPGAs using pre-synthesized parallel programming patterns, but suffers from two major limitations. First, all variant programming patterns must be pre-synthesized. Second, conditional operations are not supported. In this thesis, I present a new reconfigurable overlay, URUK, that overcomes the two limitations imposed by the JITA approach. Similar to the original JITA approach, the proposed URUK overlay allows hardware accelerators to be constructed on FPGAs through software compilation flows. To this basic capability, URUK adds additional support to enable the assembly of presynthesized fine-grained computational operators to be assembled within the FPGA. This thesis provides analysis of URUK from three different perspectives; utilization, performance, and productivity. The analysis includes comparisons against High-Level Synthesis (HLS) and the state of the art approach to creating static overlays. The tradeoffs conclude that URUK can achieve approximately equivalent performance for algebra operations compared to HLS custom accelerators, which are designed with simple experience on FPGAs. Further, URUK shows a high degree of flexibility for runtime placement and routing of the primitive operations. The analysis shows how this flexibility can be leveraged to reduce communication overhead among tiles, compared to traditional static overlays. The results also show URUK can enable software programmers without any hardware skills to create hardware accelerators at productivity levels consistent with software development and compilation

Designing Customizable Network-on-Chip with support for Embedded Private Memory for Multi-Processor System-on-Chips

The computer industry\u27s transition to multiprocessor systems on chip (MPSoC) architectures is increasing the need for new scalable high-bandwidth on-chip communication backbones. Network-on-Chip (NoC) interconnects are gaining interest for serving as the on-chip communication infrastructure. The most important issues to be considered in designing a NoC are topology, routing algorithm, flow control, and buffering and also the trade-offs between performance, power, and area. This research proposes a custom-designed NoC specifically for MPSoCs on FPGAs. The proposed design allows the communication infrastructure to seamlessly scale as the numbers of processors within the chip increases. The design adds a new level of abstraction to remote-access transactions. The design also considers support for the partitioned global address space model with support for optional embedded local memories embedded in the network interface. The network was designed as a mesh topology to allow a reasonable communication capacity in 2-Dimensional space. The communication protocol between source and destination is AMBA AXI4, and the communication between each two adjacent nodes, is typical AXI type valid/ready handshake. The nodes are distinguished by their user specified address range. Each node is assigned a range of addresses, and in each transaction, based on the destination address, the routers decide the the next node, until the transaction reaches the destination. The design has been implemented on a Xilinx Virtex7 FPGA. However, there is no platform dependency to any brand or any model of FPGAs. %In the first chapter in this research, we give an introduction of the work. In chapter 2, we talk about the background of MPSoCs and interconnections. We discuss the AXI protocl, and then we specifically talk about different Network-on-Chip projects. In chapter 3, we describe the design details for different component an also the high level design of the system, we also, discuss the implementation details of the design. In chapter 4, we show the experimental results for both verification phase and the analysis of the system. Finally, chapter 5 concludes the research

Implementation and Evaluation of an NoC Architecture for FPGAs

The Networks-on-Chip (NoC) approach for designing Systems-on-Chip (SoC) is currently emerging as an advanced concept for overcoming the scalability and efficiency problems of traditional bus-based systems. A great deal of theoretical research has been done in this area that provides good insight and shows promising results. There is a great need for research in hardware implementation of NoC-based systems to determine the feasibility of implementing various topologies and protocols, and also to accurately determine what design tradeoffs are involved in NoC implementation. This thesis addresses the challenges of implementing an NoC-based system on FPGAs for running real benchmark applications. The NoC used a mesh topology and circuit-switched communication protocol. An experimental framework was developed that allowed implementation of NoC-based system from a high level specification, using the Celoxica Handel-C hardware description language. Two test applications: charged couple device (CCD) and JPEG were developed in Handel-C to be used as our benchmark applications. Both benchmarks are computational expensive and require large quantities of data transfer that will test the NoC system. Implementation results show that the NoC-based system gives superior area utilization and speed performance compared to the bus-based system, running the same benchmarks