A framework for the selection of the right nuclear power plant

Civil nuclear reactors are used for the production of electrical energy. In the nuclear industry vendors propose several nuclear reactor designs with a size from 35–45 MWe up to 1600–1700 MWe. The choice of the right design is a multidimensional problem since a utility has to include not only financial factors as levelised cost of electricity (LCOE) and internal rate of return (IRR), but also the so called “external factors” like the required spinning reserve, the impact on local industry and the social acceptability. Therefore it is necessary to balance advantages and disadvantages of each design during the entire life cycle of the plant, usually 40–60 years. In the scientific literature there are several techniques for solving this multidimensional problem. Unfortunately it does not seem possible to apply these methodologies as they are, since the problem is too complex and it is difficult to provide consistent and trustworthy expert judgments. This paper fills the gap, proposing a two-step framework to choosing the best nuclear reactor at the pre-feasibility study phase. The paper shows in detail how to use the methodology, comparing the choice of a small-medium reactor (SMR) with a large reactor (LR), characterised, according to the International Atomic Energy Agency (2006), by an electrical output respectively lower and higher than 700 MWe

Decision support model for the selection of asphalt wearing courses in highly trafficked roads

The suitable choice of the materials forming the wearing course of highly trafficked roads is a delicate task because of their direct interaction with vehicles. Furthermore, modern roads must be planned according to sustainable development goals, which is complex because some of these might be in conflict. Under this premise, this paper develops a multi-criteria decision support model based on the analytic hierarchy process and the technique for order of preference by similarity to ideal solution to facilitate the selection of wearing courses in European countries. Variables were modelled using either fuzzy logic or Monte Carlo methods, depending on their nature. The views of a panel of experts on the problem were collected and processed using the generalized reduced gradient algorithm and a distance-based aggregation approach. The results showed a clear preponderance by stone mastic asphalt over the remaining alternatives in different scenarios evaluated through sensitivity analysis. The research leading to these results was framed in the European FP7 Project DURABROADS (No. 605404).The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under Grant Agreement No. 605404

A multi-attribute decision making procedure using fuzzy numbers and hybrid aggregators

The classical Analytical Hierarchy Process (AHP) has two limitations. Firstly, it disregards the aspect of uncertainty that usually embedded in the data or information expressed by human. Secondly, it ignores the aspect of interdependencies among attributes during aggregation. The application of fuzzy numbers aids in confronting the former issue whereas, the usage of Choquet Integral operator helps in dealing with the later issue. However, the application of fuzzy numbers into multi-attribute decision making (MADM) demands some additional steps and inputs from decision maker(s). Similarly, identification of monotone measure weights prior to employing Choquet Integral requires huge number of computational steps and amount of inputs from decision makers, especially with the increasing number of attributes. Therefore, this research proposed a MADM procedure which able to reduce the number of computational steps and amount of information required from the decision makers when dealing with these two aspects simultaneously. To attain primary goal of this research, five phases were executed. First, the concept of fuzzy set theory and its application in AHP were investigated. Second, an analysis on the aggregation operators was conducted. Third, the investigation was narrowed on Choquet Integral and its associate monotone measure. Subsequently, the proposed procedure was developed with the convergence of five major components namely Factor Analysis, Fuzzy-Linguistic Estimator, Choquet Integral, Mikhailov‘s Fuzzy AHP, and Simple Weighted Average. Finally, the feasibility of the proposed procedure was verified by solving a real MADM problem where the image of three stores located in Sabak Bernam, Selangor, Malaysia was analysed from the homemakers‘ perspective. This research has a potential in motivating more decision makers to simultaneously include uncertainties in human‘s data and interdependencies among attributes when solving any MADM problems

A methodology for the selection of new technologies in the aviation industry

The purpose of this report is to present a technology selection methodology to quantify both tangible and intangible benefits of certain technology alternatives within a fuzzy environment. Specifically, it describes an application of the theory of fuzzy sets to hierarchical structural analysis and economic evaluations for utilisation in the industry. The report proposes a complete methodology to accurately select new technologies. A computer based prototype model has been developed to handle the more complex fuzzy calculations. Decision-makers are only required to express their opinions on comparative importance of various factors in linguistic terms rather than exact numerical values. These linguistic variable scales, such as ‘very high’, ‘high’, ‘medium’, ‘low’ and ‘very low’, are then converted into fuzzy numbers, since it becomes more meaningful to quantify a subjective measurement into a range rather than in an exact value. By aggregating the hierarchy, the preferential weight of each alternative technology is found, which is called fuzzy appropriate index. The fuzzy appropriate indices of different technologies are then ranked and preferential ranking orders of technologies are found. From the economic evaluation perspective, a fuzzy cash flow analysis is employed. This deals quantitatively with imprecision or uncertainties, as the cash flows are modelled as triangular fuzzy numbers which represent ‘the most likely possible value’, ‘the most pessimistic value’ and ‘the most optimistic value’. By using this methodology, the ambiguities involved in the assessment data can be effectively represented and processed to assure a more convincing and effective decision- making process when selecting new technologies in which to invest. The prototype model was validated with a case study within the aviation industry that ensured it was properly configured to meet the

VIKOR Technique:A Systematic Review of the State of the Art Literature on Methodologies and Applications

The main objective of this paper is to present a systematic review of the VlseKriterijuska Optimizacija I Komoromisno Resenje (VIKOR) method in several application areas such as sustainability and renewable energy. This study reviewed a total of 176 papers, published in 2004 to 2015, from 83 high-ranking journals; most of which were related to Operational Research, Management Sciences, decision making, sustainability and renewable energy and were extracted from the “Web of Science and Scopus” databases. Papers were classified into 15 main application areas. Furthermore, papers were categorized based on the nationalities of authors, dates of publications, techniques and methods, type of studies, the names of the journals and studies purposes. The results of this study indicated that more papers on VIKOR technique were published in 2013 than in any other year. In addition, 13 papers were published about sustainability and renewable energy fields. Furthermore, VIKOR and fuzzy VIKOR methods, had the first rank in use. Additionally, the Journal of Expert Systems with Applications was the most significant journal in this study, with 27 publications on the topic. Finally, Taiwan had the first rank from 22 nationalities which used VIKOR technique