Effect of clock gating in conditional pulse enhancement flip-flop for low power applications

Flip-Flops (FFs) play a fundamental role in digital designs. A clock system consumes above 25% of total system power. The use of pulse-triggered flip-flops (P-FFs) in digital design provides better performance than conventional flip-flop designs. This paper presents the design of a new power-efficient implicit pulse-triggered flip-flop suitable for low power applications. This flip-flop architecture is embedded with two key features. Firstly, the enhancement in width and height of triggering pulses during specific conditions gives a solution for the longest discharging path problem in existing P-FFs. Secondly, the clock gating concept reduces unwanted switching activities at sleep/idle mode of operation and thereby reducing dynamic power consumption. The post-layout simulation results in cadence software based on CMOS 90-nm technology shows that the proposed design features less power dissipation and better power delay performance (PDP) when compared with conventional P-FFs. Its maximum power saving against conventional designs is up to 30.65%

Low Power Explicit Pulse Triggered Flip-Flop Design Based On A Pass Transistor

In VLSI system design, power consumption is the ambitious issue for the past respective years. Advanced IC fabrication technology grants the use of nano scaled devices, so the power dissipation becomes major problem in the designing of VLSI chips. In this paper we present, a low-power flip-flop (FF) design featuring an explicit type pulse-triggered structure and a modified true single phase clock latch based on a signal feed-through scheme using pass transistor. The offered design successfully figure out the long discharging path problem in conventional explicit type pulse-triggered FF (P-FF) designs and achieves better power performance by consuming low power. The proposed design also significantly reduces delay time, set-up time and hold time. Simulation results based on TMC 180nm CMOS technology reveal that the proposed design features the best power and delay performance in several FF designs under comparison

Adiabatic Flip-Flops and Sequential Circuit Design using Novel Resettable Adiabatic Buffers

We propose novel resettable adiabatic buffers for five adiabatic logic families namely; Efficient Adiabatic Charge Recovery Logic (EACRL), Improved Efficient Charge Recovery Logic (IECRL), Positive Feedback Adiabatic Logic (PFAL), Complementary Pass-transistor Adiabatic Logic (CPAL) and Clocked Adiabatic Logic (CAL). We present the design of resettable flip-flops using the proposed buffers. The proposed flip-flops alleviate the problem of increased energy and area consumption incurred by the existing mux-based resettable flip-flops. We then design the 3-bit up-down counters and extended our comparison beyond energy dissipation using the above five adiabatic logic families. PFAL based sequential circuit designs gives the best performance trade-offs in terms of complexity, energy, speed and area compared to the other adiabatic designs

Power Reductions with Energy Recovery Using Resonant Topologies

The problem of power densities in system-on-chips (SoCs) and processors has become more exacerbated recently, resulting in high cooling costs and reliability issues. One of the largest components of power consumption is the low skew clock distribution network (CDN), driving large load capacitance. This can consume as much as 70% of the total dynamic power that is lost as heat, needing elaborate sensing and cooling mechanisms. To mitigate this, resonant clocking has been utilized in several applications over the past decade. An improved energy recovering reconfigurable generalized series resonance (GSR) solution with all the critical support circuitry is developed in this work. This LC resonant clock driver is shown to save about 50% driver power (\u3e40% overall), on a 22nm process node and has 50% less skew than a non-resonant driver at 2GHz. It can operate down to 0.2GHz to support other energy savings techniques like dynamic voltage and frequency scaling (DVFS). As an example, GSR can be configured for the simpler pulse series resonance (PSR) operation to enable further power saving for double data rate (DDR) applications, by using de-skewing latches instead of flip-flop banks. A PSR based subsystem for 40% savings in clocking power with 40% driver active area reduction xii is demonstrated. This new resonant driver generates tracking pulses at each transition of clock for dual edge operation across DVFS. PSR clocking is designed to drive explicit-pulsed latches with negative setup time. Simulations using 45nm IBM/PTM device and interconnect technology models, clocking 1024 flip-flops show the reductions, compared to non-resonant clocking. DVFS range from 2GHz/1.3V to 200MHz/0.5V is obtained. The PSR frequency is set \u3e3× the clock rate, needing only 1/10th the inductance of prior-art LC resonance schemes. The skew reductions are achieved without needing to increase the interconnect widths owing to negative set-up times. Applications in data circuits are shown as well with a 90nm example. Parallel resonant and split-driver non-resonant configurations as well are derived from GSR. Tradeoffs in timing performance versus power, based on theoretical analysis, are compared for the first time and verified. This enables synthesis of an optimal topology for a given application from the GSR

Energy efficiency of 2- Step power-clocks for adiabatic logic

The generation of power-clocks in adiabatic integrated circuits is investigated. Specifically, we consider the energy efficiency of a 2-step charging strategy based on a single tank-capacitor circuit. We have investigated the impact of various parameters such as tank-capacitance to load capacitance ratio, ramping time, transistors sizing and power supply voltage scaling on energy recovery achievable in the 2-step charging circuit. We show that energy recovery achievable in the 2-step charging circuit depends on the tank-capacitor and load capacitor size concluding that tank-capacitance (CT) versus load capacitance (CL) is the significant parameter. We also show that the energy performance depends on the ramping time and improves for higher ramping times (lower frequencies). Energy recovery also improves if the transistors sizes in the step charging circuit are sized at their minimum dimensions. Lastly, we show that energy recovery decreases as the power supply voltage is scaled down. Specifically, the decrease in the energy recovery with decreasing power supply is significant for lower ramping times (higher frequencies). We propose that a Ct/Cl ratio of 10, keeping the width of the transistors in the step charging circuit minimum, can be chosen as a convenient `rule-of-thumb' in practical designs

Research on low power technology by AC power supply circuits

制度:新 ; 報告番号:甲3692号 ; 学位の種類:博士(工学) ; 授与年月日:2012/9/15 ; 早大学位記番号:新6060Waseda Universit

Energy-Efficient Neural Network Architectures

Emerging systems for artificial intelligence (AI) are expected to rely on deep neural networks (DNNs) to achieve high accuracy for a broad variety of applications, including computer vision, robotics, and speech recognition. Due to the rapid growth of network size and depth, however, DNNs typically result in high computational costs and introduce considerable power and performance overheads. Dedicated chip architectures that implement DNNs with high energy efficiency are essential for adding intelligence to interactive edge devices, enabling them to complete increasingly sophisticated tasks by extending battery lie. They are also vital for improving performance in cloud servers that support demanding AI computations. This dissertation focuses on architectures and circuit technologies for designing energy-efficient neural network accelerators. First, a deep-learning processor is presented for achieving ultra-low power operation. Using a heterogeneous architecture that includes a low-power always-on front-end and a selectively-enabled high-performance back-end, the processor dynamically adjusts computational resources at runtime to support conditional execution in neural networks and meet performance targets with increased energy efficiency. Featuring a reconfigurable datapath and a memory architecture optimized for energy efficiency, the processor supports multilevel dynamic activation of neural network segments, performing object detection tasks with 5.3x lower energy consumption in comparison with a static execution baseline. Fabricated in 40nm CMOS, the processor test-chip dissipates 0.23mW at 5.3 fps. It demonstrates energy scalability up to 28.6 TOPS/W and can be configured to run a variety of workloads, including severely power-constrained ones such as always-on monitoring in mobile applications. To further improve the energy efficiency of the proposed heterogeneous architecture, a new charge-recovery logic family, called zero-short-circuit current (ZSCC) logic, is proposed to decrease the power consumption of the always-on front-end. By relying on dedicated circuit topologies and a four-phase clocking scheme, ZSCC operates with significantly reduced short-circuit currents, realizing order-of-magnitude power savings at relatively low clock frequencies (in the order of a few MHz). The efficiency and applicability of ZSCC is demonstrated through an ANSI S1.11 1/3 octave filter bank chip for binaural hearing aids with two microphones per ear. Fabricated in a 65nm CMOS process, this charge-recovery chip consumes 13.8µW with a 1.75MHz clock frequency, achieving 9.7x power reduction per input in comparison with a 40nm monophonic single-input chip that represents the published state of the art. The ability of ZSCC to further increase the energy efficiency of the heterogeneous neural network architecture is demonstrated through the design and evaluation of a ZSCC-based front-end. Simulation results show 17x power reduction compared with a conventional static CMOS implementation of the same architecture.PHDElectrical and Computer EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/147614/1/hsiwu_1.pd

Adiabatic Circuits for Power-Constrained Cryptographic Computations

This thesis tackles the need for ultra-low power operation in power-constrained cryptographic computations. An example of such an application could be smartcards. One of the techniques which has proven to have the potential of rendering ultra-low power operation is ‘Adiabatic Logic Technique’. However, the adiabatic circuits has associated challenges due to high energy dissipation of the Power-Clock Generator (PCG) and complexity of the multi-phase power-clocking scheme. Energy efficiency of the adiabatic system is often degraded due to the high energy dissipation of the PCG. In this thesis, nstep charging strategy using tank capacitors is considered for the power-clock generation and several design rules and trade-offs between the circuit complexity and energy efficiency of the PCG using n-step charging circuits have been proposed. Since pipelining is inherent in adiabatic logic design, careful selection of architecture is essential, as otherwise overhead in terms of area and energy due to synchronization buffers is induced specifically, in the case of adiabatic designs using 4-phase power-clocking scheme. Several architectures for the Montgomery multiplier using adiabatic logic technique are implemented and compared. An architecture which constitutes an appropriate trade-off between energy efficiency and throughput is proposed along with its methodology. Also, a strategy to reduce the overhead due to synchronization buffers is proposed. A modification in the Montgomery multiplication algorithm is proposed. Furthermore, a problem due to the application of power-clock gating in cascade stages of adiabatic logic is identified. The problem degrades the energy savings that would otherwise be obtained by the application of power-clock gating. A solution to this problem is proposed. Cryptographic implementations also present an obvious target for Power Analysis Attacks (PAA). There are several existing secure adiabatic logic designs which are proposed as a countermeasure against PAA. Shortcomings of the existing logic designs are identified, and two novel secure adiabatic logic designs are proposed as the countermeasures against PAA and improvement over the existing logic designs

Timing speculation and adaptive reliable overclocking techniques for aggressive computer systems

Computers have changed our lives beyond our own imagination in the past several decades. The continued and progressive advancements in VLSI technology and numerous micro-architectural innovations have played a key role in the design of spectacular low-cost high performance computing systems that have become omnipresent in today\u27s technology driven world. Performance and dependability have become key concerns as these ubiquitous computing machines continue to drive our everyday life. Every application has unique demands, as they run in diverse operating environments. Dependable, aggressive and adaptive systems improve efficiency in terms of speed, reliability and energy consumption. Traditional computing systems run at a fixed clock frequency, which is determined by taking into account the worst-case timing paths, operating conditions, and process variations. Timing speculation based reliable overclocking advocates going beyond worst-case limits to achieve best performance while not avoiding, but detecting and correcting a modest number of timing errors. The success of this design methodology relies on the fact that timing critical paths are rarely exercised in a design, and typical execution happens much faster than the timing requirements dictated by worst-case design methodology. Better-than-worst-case design methodology is advocated by several recent research pursuits, which exploit dependability techniques to enhance computer system performance. In this dissertation, we address different aspects of timing speculation based adaptive reliable overclocking schemes, and evaluate their role in the design of low-cost, high performance, energy efficient and dependable systems. We visualize various control knobs in the design that can be favorably controlled to ensure different design targets. As part of this research, we extend the SPRIT3E, or Superscalar PeRformance Improvement Through Tolerating Timing Errors, framework, and characterize the extent of application dependent performance acceleration achievable in superscalar processors by scrutinizing the various parameters that impact the operation beyond worst-case limits. We study the limitations imposed by short-path constraints on our technique, and present ways to exploit them to maximize performance gains. We analyze the sensitivity of our technique\u27s adaptiveness by exploring the necessary hardware requirements for dynamic overclocking schemes. Experimental analysis based on SPEC2000 benchmarks running on a SimpleScalar Alpha processor simulator, augmented with error rate data obtained from hardware simulations of a superscalar processor, are presented. Even though reliable overclocking guarantees functional correctness, it leads to higher power consumption. As a consequence, reliable overclocking without considering on-chip temperatures will bring down the lifetime reliability of the chip. In this thesis, we analyze how reliable overclocking impacts the on-chip temperature of a microprocessor and evaluate the effects of overheating, due to such reliable dynamic frequency tuning mechanisms, on the lifetime reliability of these systems. We then evaluate the effect of performing thermal throttling, a technique that clamps the on-chip temperature below a predefined value, on system performance and reliability. Our study shows that a reliably overclocked system with dynamic thermal management achieves 25% performance improvement, while lasting for 14 years when being operated within 353K. Over the past five decades, technology scaling, as predicted by Moore\u27s law, has been the bedrock of semiconductor technology evolution. The continued downscaling of CMOS technology to deep sub-micron gate lengths has been the primary reason for its dominance in today\u27s omnipresent silicon microchips. Even as the transition to the next technology node is indispensable, the initial cost and time associated in doing so presents a non-level playing field for the competitors in the semiconductor business. As part of this thesis, we evaluate the capability of speculative reliable overclocking mechanisms to maximize performance at a given technology level. We evaluate its competitiveness when compared to technology scaling, in terms of performance, power consumption, energy and energy delay product. We present a comprehensive comparison for integer and floating point SPEC2000 benchmarks running on a simulated Alpha processor at three different technology nodes in normal and enhanced modes. Our results suggest that adopting reliable overclocking strategies will help skip a technology node altogether, or be competitive in the market, while porting to the next technology node. Reliability has become a serious concern as systems embrace nanometer technologies. In this dissertation, we propose a novel fault tolerant aggressive system that combines soft error protection and timing error tolerance. We replicate both the pipeline registers and the pipeline stage combinational logic. The replicated logic receives its inputs from the primary pipeline registers while writing its output to the replicated pipeline registers. The organization of redundancy in the proposed Conjoined Pipeline system supports overclocking, provides concurrent error detection and recovery capability for soft errors, intermittent faults and timing errors, and flags permanent silicon defects. The fast recovery process requires no checkpointing and takes three cycles. Back annotated post-layout gate-level timing simulations, using 45nm technology, of a conjoined two-stage arithmetic pipeline and a conjoined five-stage DLX pipeline processor, with forwarding logic, show that our approach, even under a severe fault injection campaign, achieves near 100% fault coverage and an average performance improvement of about 20%, when dynamically overclocked

Power Reduction Techniques in Clock Distribution Networks with Emphasis on LC Resonant Clocking

In this thesis we propose a set of independent techniques in the overall concept of LC resonant clocking where each technique reduces power consumption and improve system performance. Low-power design is becoming a crucial design objective due to the growing demand on portable applications and the increasing difficulties in cooling and heat removal. The clock distribution network delivers the clock signal which acts as a reference to all sequential elements in the synchronous system. The clock distribution network consumes a considerable amount of power in synchronous digital systems. Resonant clocking is an emerging promising technique to reduce the power of the clock network. The inductor used in resonant clocking enables the conversion of the electric energy stored on the clock capacitance to magnetic energy in the inductor and vice versa. In this thesis, the concept of the slack in the clock skew has been extended for an LC fully-resonant clock distribution network. This extra slack in comparison to standard clock distribution networks can be used to reduce routing complexity, achieve reduction in wire elongation, total wire length, and power consumption. Simulation results illustrate that by utilizing the proposed approach, an average reduction of 53% in the number of wire elongations and 11% reduction in total wire length can be achieved. A dual-edge clocking scheme introduced in the literature to enable the operation of the flip-flop at the rising- and falling edges of the clock has been modified. The interval by which the charging elements in the flip-flop are being switched-on was reduced causing a reduction in power consumption. Simulating the flip-flop in STMicroelectronics 90-nm technology shows correct functionality of the Sense Amplifier flip-flop with a resonant clock signal of 500 MHz and a throughput of 1 GHz under process, voltage, and temperature (PVT) variations. Modeling the resonant system with the proposed flip-flop illustrates that dual-edge compared to single-edge triggering can achieve up to 58% reduction in power consumption when the clock capacitance is the dominating factor. The application of low-swing clocking to LC resonant clock distribution network has been investigated on-chip. The proposed low-swing resonant clocking scheme operates with one voltage supply and does not require an additional supply voltage. The Differential Conditional Capturing flip-flop introduced in the literature was modified to operate with a low-swing sinusoidal clock. Low-swing resonant clocking achieved around 5.8% reduction in total power with 5.7% area overhead. Modeling the clock network with the proposed flip-flop illustrates that low-swing clocking can achieve up to 58% reduction in the power consumption of the resonant clock. An analytical approach was introduced to estimate the required driver strength in the clock generator. Using the proposed approach early in the design stage reduces area and power overhead by eliminating the need for programmable switches in the driving circuit