SatCat5: A Low-Power, Mixed-Media Ethernet Network for Smallsats

In any satellite, internal bus and payload systems must exchange a variety of command, control, telemetry, and mission-data. In too many cases, the resulting network is an ad-hoc proliferation of complex, dissimilar protocols with incomplete system-to-system connectivity. While standards like CAN, MIL-STD-1553, and SpaceWire mitigate this problem, none can simultaneously solve the need for high throughput and low power consumption. We present a new solution that uses Ethernet framing and addressing to unify a mixed-media network. Low-speed nodes (0.1-10 Mbps) use simple interfaces such as SPI and UART to communicate with extremely low power and minimal complexity. High-speed nodes use so-called “media-independent” interfaces such as RMII, RGMII, and SGMII to communicate at rates up to 1000 Mbps and enable connection to traditional COTS network equipment. All are interconnected into a single smallsat-area-network using a Layer-2 network switch, with mixed-media support for all these interfaces on a single network. The result is fast, easy, and flexible communication between any two subsystems. SatCat5 is presented as a free and open-source reference implementation of this mixed-media network switch, with power consumption of 0.2-0.7W depending on network activity. Further discussion includes example protocols that can be used on such networks, leveraging IPv4 when suitable but also enabling full-featured communication without the need for a complex protocol stack

Multicast Mobility in Mobile IP Version 6 (MIPv6) : Problem Statement and Brief Survey

Publisher PD

IP and ATM integration: A New paradigm in multi-service internetworking

ATM is a widespread technology adopted by many to support advanced data communication, in particular efficient Internet services provision. The expected challenges of multimedia communication together with the increasing massive utilization of IP-based applications urgently require redesign of networking solutions in terms of both new functionalities and enhanced performance. However, the networking context is affected by so many changes, and to some extent chaotic growth, that any approach based on a structured and complex top-down architecture is unlikely to be applicable. Instead, an approach based on finding out the best match between realistic service requirements and the pragmatic, intelligent use of technical opportunities made available by the product market seems more appropriate. By following this approach, innovations and improvements can be introduced at different times, not necessarily complying with each other according to a coherent overall design. With the aim of pursuing feasible innovations in the different networking aspects, we look at both IP and ATM internetworking in order to investigating a few of the most crucial topics/ issues related to the IP and ATM integration perspective. This research would also address various means of internetworking the Internet Protocol (IP) and Asynchronous Transfer Mode (ATM) with an objective of identifying the best possible means of delivering Quality of Service (QoS) requirements for multi-service applications, exploiting the meritorious features that IP and ATM have to offer. Although IP and ATM often have been viewed as competitors, their complementary strengths and limitations from a natural alliance that combines the best aspects of both the technologies. For instance, one limitation of ATM networks has been the relatively large gap between the speed of the network paths and the control operations needed to configure those data paths to meet changing user needs. IP\u27s greatest strength, on the other hand, is the inherent flexibility and its capacity to adapt rapidly to changing conditions. These complementary strengths and limitations make it natural to combine IP with ATM to obtain the best that each has to offer. Over time many models and architectures have evolved for IP/ATM internetworking and they have impacted the fundamental thinking in internetworking IP and ATM. These technologies, architectures, models and implementations will be reviewed in greater detail in addressing possible issues in integrating these architectures s in a multi-service, enterprise network. The objective being to make recommendations as to the best means of interworking the two in exploiting the salient features of one another to provide a faster, reliable, scalable, robust, QoS aware network in the most economical manner. How IP will be carried over ATM when a commercial worldwide ATM network is deployed is not addressed and the details of such a network still remain in a state of flux to specify anything concrete. Our research findings culminated with a strong recommendation that the best model to adopt, in light of the impending integrated service requirements of future multi-service environments, is an ATM core with IP at the edges to realize the best of both technologies in delivering QoS guarantees in a seamless manner to any node in the enterprise

Design of a New High Bandwidth Network for Agricultural Machines

Ethernet is by now the most adopted bus for fast digital communications in many environments, from household entertainment to PLC robotics in industrial assembly lines. Even in automotive industry, the interest in this technology is increasingly growing, pushed forward by research and by the need of high throughput that high dynamics distributed control demands. Although 100base-TX physical layer (PHY) does not seem to meet EMC requirements for vehicular and heavy-duty environments, OPEN Alliance BroadR Reach (soon becoming IEEE standard as IEEE 802.3bw) technology is the most promising and already adopted Ethernet-compatible PHY, reaching 100Mbps over an unshielded twisted pair. An agricultural machine is usually a system including tractor and one or more implements attached to it, to the back or to the front. Nowadays, a specific CAN-based distributed control network support treatments and applications, namely ISOBUS, defined by ISO 11783. This work deals with architectural and technological aspects of advanced Ethernet networks in order to provide a high-throughput deterministic network for in-vehicle distributed control for agricultural machinery. Two main paths of investigation will be presented: one concerning the prioritization of standard Ethernet taking advantage of standard ways of prioritization in well-established technologies; the other changing the channel access method of Ethernet using an industrial fieldbus, chosen after careful investigation. The prioritization of standard Ethernet is performed at two, non-mutual exclusive layers of the ISO OSI stack: one at L3, using the diffserv (former TOS) Ip field; one at L2, using the priorities defined in IEEE 802.1p, used in IEEE 802.1q (VLAN). These choices have several implications in the specific field of application of the agricultural machines. The change of the access method, instead, focused on the adoption of a specific fieldbus, in order to grant deterministic access to the medium and reliability of communications for safety-relevant applications. After a survey, that will be reported, the Powerlink fieldbus was chosen and some modifications will be discussed in order to suit the scope of the research

Performance Analysis of NICs and Its Interactivity with Internet Services

This paper analyses the problem of slow data or video streaming on the World Wide Web internet through the network interface cards (NICs). The service of the entire network and internet connectivity largely rest on the installed Network Interface Cards (NICs). The performance of the various NICs such as 10Mbps, 100Mbps, 1,000Mbps and 10,000Mbps were examined using different message data sizes on the network. Also, the paper extensively discusses the performance of 10Gbps Ethernet card such as: data transmission time and throughput. The fact remained that the major backbone of the Internet network is the transmission control protocol (TCP) which is designed for reliable sending of data over the internet. The TCP as the protocol of the NIC is used for browsing web and downloading or uploading files. Additionally, the paper also examines the TCP feedback mechanism that is able to detect loss packets and retransmit them. Also, the TCP is able to dynamically adapt its packet sending rate to the network conditions in order to achieve the highest possible throughput. However, this paper proposes the use of the 10Gbps Ethernet card for the Internet Servers and Workstations for effective and fast internet access in all public networks. Keywords: Ethernet Card, Transmission Control Protocol, Data transmission time, throughput.

Moving target network steganography

A branch of information hiding that has gained traction in recent years is network steganography. Network steganography uses network protocols are carriers to hide and transmit data. Storage channel network steganography manipulates values in protocol header and data fields and stores covert data inside them. The timing channel modulates the timing of events in the protocol to transfer covert information. Many current storage channel network steganography methods have low bandwidths and they hide covert data directly into the protocol which allows discoverers of the channel to read the confidential information. A new type of storage channel network steganography method is proposed and implemented which abstracts the idea of hiding data inside the network protocol. The addition of a moving target mechanism rotates the locations of data to be evaluated preventing brute force attacks. The bandwidth of the algorithm can also be controlled by increasing or decreasing the rate of packet transmission. A proof of concept is developed to implement the algorithm. Experimental run times are compared with their theoretical equivalents to compare the accuracy of the proof of concept. Detailed probability and data transfer analysis is performed on the algorithm to see how the algorithm functions in terms of security and bandwidth. Finally, a detection and mitigation analysis is performed to highlight the flaws with the algorithm and how they can be improved

Decentralization of multimedia content in a heterogeneous environment

The aim of this study has been the decentralization of multimedia content in a heterogeneous environment. The environment consisted of the research networks connecting the European Organization for Nuclear Research and the Finnish University and Research Network. The European Organization for Nuclear Research produces multimedia content which can be used as studying material all over the world. The Web University pilot in the European Organization for Nuclear Research has been developing a multimedia content delivery service for years. Delivering the multimedia content requires plenty of capacity from the network infrastructure. Different content of the material can have different demands for the network. In a heterogeneous environment, like the Internet, fulfilling all the demands can be a problem. Several methods exist to improve the situation. Decentralization of the content is one of the most popular solutions. Mirroring and caching are the main methods for decentralization. Recently developed content delivery networks are using both of these techniques to satisfy the demands of the content. The practical application consisted of measurements of the network connection between the multimedia server in the European Organization for Nuclear Research and the Finnish University and Research Network, planning and building a decentralization system for the multimedia content. After the measurements, it became clear that there is n o need for decentralization of the multimedia content for users that are able to utilise the Finnish University and Research Network. There could be double today's usage, and still there would be no problems with the capacity. However, the European Organization for Nuclear Research routes all traffic that comes from outside research networks through a gateway in the USA. This affects every connection that is made from Finland: users are not able to use the international connection offered by the Finnish University and Research Network. For these users I designed and built a simple, modular and portable decentralization system

Gateway design for LAN interconnection via ISDN

Computer Networks and ISDN Systems19143-5

Development of communication protocolbased on low voltage distribution automation system

This paper presents the development of a customer side distribution automation system (DAS) for operating and controlling low voltage (LV) down stream of 415/240V by using the Tenaga Nasional Berhad (TNB) distribution system. Supervisory Control and Data Acquisition (SCADA) based remote Terminal Unit (RTU) along power line communication PLC) system are used for DAS development that practically imulates the down stream distribution system functions in an automated manner. It is the first DAS research work done on customer side substation for operating and controlling between the consumer side system and the substation. Most of the work is focused on building Human Machine Interface that provides a graphical operator interface function to monitor the system. The Human Machine Interface of SCADA system is developed using customized software and an RTU microprocessor and its software implements

A Companion Study Guide for the Cisco DCICN Data Center Certification Exam (200-150)

The official Cisco DCICN book and practice exams are great resources, but this is not an easy exam. This study guide is a companion to those resources and summarizes the subject areas into additional review questions with an answer description for each item. This book is not a braindump and it is not bootleg screenshots of the actual exam. Instead, this book provides additional context and examples, serves to complement other study guides, and provides additional examples. If you are getting ready to take the exam for the first time, I hope that this guide provides the extra help to pass! If you are up for re-certification, I hope that this guide serves as a refresher and reminder! Keep working hard, keep studying, and never stop learning…https://digitalcommons.odu.edu/distancelearning_books/1000/thumbnail.jp