221 research outputs found
Task-space dynamic control of underwater robots
This thesis is concerned with the control aspects for underwater tasks performed by
marine robots. The mathematical models of an underwater vehicle and an underwater
vehicle with an onboard manipulator are discussed together with their associated
properties.
The task-space regulation problem for an underwater vehicle is addressed where the
desired target is commonly specified as a point. A new control technique is proposed
where the multiple targets are defined as sub-regions. A fuzzy technique is used to
handle these multiple sub-region criteria effectively. Due to the unknown gravitational
and buoyancy forces, an adaptive term is adopted in the proposed controller.
An extension to a region boundary-based control law is then proposed for an underwater
vehicle to illustrate the flexibility of the region reaching concept. In this novel
controller, a desired target is defined as a boundary instead of a point or region. For a
mapping of the uncertain restoring forces, a least-squares estimation algorithm and the
inverse Jacobian matrix are utilised in the adaptive control law.
To realise a new tracking control concept for a kinematically redundant robot, subregion
tracking control schemes with a sub-tasks objective are developed for a UVMS.
In this concept, the desired objective is specified as a moving sub-region instead of a
trajectory. In addition, due to the system being kinematically redundant, the controller
also enables the use of self-motion of the system to perform sub-tasks (drag
minimisation, obstacle avoidance, manipulability and avoidance of mechanical joint
limits)
AI based Robot Safe Learning and Control
Introduction This open access book mainly focuses on the safe control of robot manipulators. The control schemes are mainly developed based on dynamic neural network, which is an important theoretical branch of deep reinforcement learning. In order to enhance the safety performance of robot systems, the control strategies include adaptive tracking control for robots with model uncertainties, compliance control in uncertain environments, obstacle avoidance in dynamic workspace. The idea for this book on solving safe control of robot arms was conceived during the industrial applications and the research discussion in the laboratory. Most of the materials in this book are derived from the authors’ papers published in journals, such as IEEE Transactions on Industrial Electronics, neurocomputing, etc. This book can be used as a reference book for researcher and designer of the robotic systems and AI based controllers, and can also be used as a reference book for senior undergraduate and graduate students in colleges and universities
Repeatable Motion Planning for Redundant Robots over Cyclic Tasks
We consider the problem of repeatable motion planning for redundant robotic systems performing cyclic tasks in the presence of obstacles. For this open problem, we present a control-based randomized planner, which produces closed collision-free paths in configuration space and guarantees continuous satisfaction of the task constraints. The proposed algorithm, which relies on bidirectional search and loop closure in the task-constrained configuration space, is shown to be probabilistically complete. A modified version of the planner is also devised for the case in which configuration-space paths are required to be smooth. Finally, we present planning results in various scenarios involving both free-flying and nonholonomic robots to show the effectiveness of the proposed method
Kontextsensitive Körperregulierung für redundante Roboter
In the past few decades the classical 6 degrees of freedom manipulators' dominance has been challenged by the rise of 7 degrees of freedom redundant robots. Similarly, with increased availability of humanoid robots in academic research, roboticists suddenly have access to highly dexterous platforms with multiple kinematic chains capable of undertaking multiple tasks simultaneously. The execution of lower-priority tasks, however, are often done in task/scenario specific fashion. Consequently, these systems are not scalable and slight changes in the application often implies re-engineering the entire control system and deployment which impedes the development process over time.
This thesis introduces an alternative systematic method of addressing the secondary tasks and redundancy resolution called, context aware body regulation. Contexts consist of one or multiple tasks, however, unlike the conventional definitions, the tasks within a context are not rigidly defined and maintain some level of abstraction. For instance, following a particular trajectory constitutes a concrete task while performing a Cartesian motion with the end-effector represents an abstraction of the same task and is more appropriate for context formulation. Furthermore, contexts are often made up of multiple abstract tasks that collectively describe a reoccurring situation. Body regulation is an umbrella term for a collection of schemes for addressing the robots' redundancy when a particular context occurs.
Context aware body regulation offers several advantages over traditional methods. Most notably among them are reusability, scalability and composability of contexts and body regulation schemes. These three fundamental concerns are realized theoretically by in-depth study and through mathematical analysis of contexts and regulation strategies; and are practically implemented by a component based software architecture that complements the theoretical aspects.
The findings of the thesis are applicable to any redundant manipulator and humanoids, and allow them to be used in real world applications. Proposed methodology presents an alternative approach for the control of robots and offers a new perspective for future deployment of robotic solutions.Im Verlauf der letzten Jahrzehnte wich der Einfluss klassischer Roboterarme mit 6 Freiheitsgraden zunehmend denen neuer und vielfältigerer Manipulatoren mit 7 Gelenken. Ebenso stehen der Forschung mit den neuartigen Humanoiden inzwischen auch hoch-redundante Roboterplattformen mit mehreren kinematischen Ketten zur Verfügung. Diese überaus flexiblen und komplexen Roboter-Kinematiken ermöglichen generell das gleichzeitige Verfolgen mehrerer priorisierter Bewegungsaufgaben. Die Steuerung der weniger wichtigen Aufgaben erfolgt jedoch oft in anwendungsspezifischer Art und Weise, welche die Skalierung der Regelung zu generellen Kontexten verhindert. Selbst kleine Änderungen in der Anwendung bewirken oft schon, dass große Teile der Robotersteuerung überarbeitet werden müssen, was wiederum den gesamten Entwicklungsprozess behindert.
Diese Dissertation stellt eine alternative, systematische Methode vor um die Redundanz neuer komplexer Robotersysteme zu bewältigen und vielfältige, priorisierte Bewegungsaufgaben parallel zu steuern: Die so genannte kontextsensitive Körperregulierung. Darin bestehen Kontexte aus einer oder mehreren Bewegungsaufgaben. Anders als in konventionellen Anwendungen sind die Aufgaben nicht fest definiert und beinhalten eine gewisse Abstraktion. Beispielsweise stellt das Folgen einer bestimmten Trajektorie eine sehr konkrete Bewegungsaufgabe dar, während die Ausführung einer Kartesischen Bewegung mit dem Endeffektor eine Abstraktion darstellt, die für die Kontextformulierung besser geeignet ist. Kontexte setzen sich oft aus mehreren solcher abstrakten Aufgaben zusammen und beschreiben kollektiv eine sich wiederholende Situation.
Durch die Verwendung der kontextsensitiven Körperregulierung ergeben sich vielfältige Vorteile gegenüber traditionellen Methoden: Wiederverwendbarkeit, Skalierbarkeit, sowie Komponierbarkeit von Konzepten. Diese drei fundamentalen Eigenschaften werden in der vorliegenden Arbeit theoretisch mittels gründlicher mathematischer Analyse aufgezeigt und praktisch mittels einer auf Komponenten basierenden Softwarearchitektur realisiert.
Die Ergebnisse dieser Dissertation lassen sich auf beliebige redundante Manipulatoren oder humanoide Roboter anwenden und befähigen diese damit zur realen Anwendung außerhalb des Labors. Die hier vorgestellte Methode zur Regelung von Robotern stellt damit eine neue Perspektive für die zukünftige Entwicklung von robotischen Lösungen dar
Modeling and control of an anthropomorphic robotic hand
Mención Europea en el título de doctorThis thesis presents methods and tools for enabling the successful use of
robotic hands. For highly dexterous and/or anthropomorphic robotic hands,
these methods have to share some common goals, such as overcoming the
potential complexity of the mechanical design and the ability of performing
accurate tasks with low and efficient computational cost.
A prerequisite for dexterity is to increase the workspace of the robotic hand.
For this purpose, the robotic hand must be considered as a single multibody
system. Solving the inverse kinematics problem of the whole robotic hand is
an arduous task due to the high number of degrees of freedom involved and
the possible mechanical limitations, singularities and other possible constraints.
The redundancy has proven to be of a great usefulness for dealing
with potential constraints. To be able to exploit the redundancy for dealing
with constraints, the adopted method for solving the inverse kinematics
must be robust and extendable. Obviously, addressing such complex problem,
the method will certainly be computationally heavy. Thus, one of the
aims of this thesis is to resolve the inverse kinematics problem of the whole
robotic hand under constraints, taking into account the computational cost.
To this end, this thesis extends and reduces the most recent Selectively
Damped Least Squares method which is based on the computation of all
singular values, to deal with constraints with a minimum computational
cost. New estimation algorithm of singular values and their corresponding
singular vectors is proposed to reduce the computational cost. The reduced
extended selectively damped least squares method is simulated and experimentally
evaluated using an anthropomorphic robotic hand as a test bed.
On the other hand, dexterity depends not only on the accuracy of the position
control, but also on the exerted forces. The tendon driven modern robotic hands, like the one used in this work, are strongly nonlinear dynamic
systems, where motions and forces are transmitted remotely to the
finger joints. The problem of modeling and control of position and force
simultaneously at low level control is then considered. A new hybrid control
structure based on the succession of two sliding mode controllers is
proposed. The force is controlled by its own controller which does not need
a contact model. The performance of the proposed controller is evaluated
by performing the force control directly using the force sensor information
of the fingertip, and indirectly using the torque control of the actuator.
Finally, we expect that the applications of the methods presented in this
thesis can be extended to cover different issues and research fields and in
particular they can be used in a variety of algorithm that require the estimation
of singular values.This work was partially supported by the European project HANDLE, FP7-231640, and by the Spanish ministry MICINN through FPI scholarship within the project DPI-2005-04302.Programa Oficial de Doctorado en Ingeniería Eléctrica, Electrónica y AutomáticaPresidente: Anis Sahbani.- Secretario: Fares Jawad Moh D Abu-Dakka.- Vocal: Claudio Ross
Geometry-aware Manipulability Learning, Tracking and Transfer
Body posture influences human and robots performance in manipulation tasks,
as appropriate poses facilitate motion or force exertion along different axes.
In robotics, manipulability ellipsoids arise as a powerful descriptor to
analyze, control and design the robot dexterity as a function of the
articulatory joint configuration. This descriptor can be designed according to
different task requirements, such as tracking a desired position or apply a
specific force. In this context, this paper presents a novel
\emph{manipulability transfer} framework, a method that allows robots to learn
and reproduce manipulability ellipsoids from expert demonstrations. The
proposed learning scheme is built on a tensor-based formulation of a Gaussian
mixture model that takes into account that manipulability ellipsoids lie on the
manifold of symmetric positive definite matrices. Learning is coupled with a
geometry-aware tracking controller allowing robots to follow a desired profile
of manipulability ellipsoids. Extensive evaluations in simulation with
redundant manipulators, a robotic hand and humanoids agents, as well as an
experiment with two real dual-arm systems validate the feasibility of the
approach.Comment: Accepted for publication in the Intl. Journal of Robotics Research
(IJRR). Website: https://sites.google.com/view/manipulability. Code:
https://github.com/NoemieJaquier/Manipulability. 24 pages, 20 figures, 3
tables, 4 appendice
Proceedings of the NASA Conference on Space Telerobotics, volume 1
The theme of the Conference was man-machine collaboration in space. Topics addressed include: redundant manipulators; man-machine systems; telerobot architecture; remote sensing and planning; navigation; neural networks; fundamental AI research; and reasoning under uncertainty
Robot Manipulators
Robot manipulators are developing more in the direction of industrial robots than of human workers. Recently, the applications of robot manipulators are spreading their focus, for example Da Vinci as a medical robot, ASIMO as a humanoid robot and so on. There are many research topics within the field of robot manipulators, e.g. motion planning, cooperation with a human, and fusion with external sensors like vision, haptic and force, etc. Moreover, these include both technical problems in the industry and theoretical problems in the academic fields. This book is a collection of papers presenting the latest research issues from around the world
Postprocesamiento CAM-ROBOTICA orientado al prototipado y mecanizado en células robotizadas complejas
The main interest of this thesis consists of the study and implementation of postprocessors to adapt the toolpath generated by a Computer Aided Manufacturing (CAM) system to a complex robotic workcell of eight joints, devoted to the rapid prototyping of 3D CAD-defined products. It consists of a 6R industrial manipulator mounted on a linear track and synchronized with a rotary table. To accomplish this main objective, previous work is required. Each task carried out entails a methodology, objective and partial results that complement each other, namely:
- It is described the architecture of the workcell in depth, at both displacement and joint-rate levels, for both direct and inverse resolutions. The conditioning of the Jacobian matrix is described as kinetostatic performance index to evaluate the vicinity to singular postures. These ones are analysed from a geometric point of view.
- Prior to any machining, the additional external joints require a calibration done in situ, usually in an industrial environment. A novel Non-contact Planar Constraint Calibration method is developed to estimate the external joints configuration parameters by means of a laser displacement sensor.
- A first control is originally done by means of a fuzzy inference engine at the displacement level, which is integrated within the postprocessor of the CAM software.
- Several Redundancy Resolution Schemes (RRS) at the joint-rate level are compared for the configuration of the postprocessor, dealing not only with the additional joints (intrinsic redundancy) but also with the redundancy due to the symmetry on the milling tool (functional redundancy).
- The use of these schemes is optimized by adjusting two performance criterion vectors related to both singularity avoidance and maintenance of a preferred reference posture, as secondary tasks to be done during the path tracking. Two innovative fuzzy inference engines actively adjust the weight of each joint in these tasks.Andrés De La Esperanza, FJ. (2011). Postprocesamiento CAM-ROBOTICA orientado al prototipado y mecanizado en células robotizadas complejas [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/10627Palanci
- …