Ultra-Low Power Circuit Design for Cubic-Millimeter Wireless Sensor Platform.

Modern daily life is surrounded by smaller and smaller computing devices. As Bell’s Law predicts, the research community is now looking at tiny computing platforms and mm3-scale sensor systems are drawing an increasing amount of attention since they can create a whole new computing environment. Designing mm3-scale sensor nodes raises various circuit and system level challenges and we have addressed and proposed novel solutions for many of these challenges to create the first complete 1.0mm3 sensor system including a commercial microprocessor. We demonstrate a 1.0mm3 form factor sensor whose modular die-stacked structure allows maximum volume utilization. Low power I2C communication enables inter-layer serial communication without losing compatibility to standard I2C communication protocol. A dual microprocessor enables concurrent computation for the sensor node control and measurement data processing. A multi-modal power management unit allowed energy harvesting from various harvesting sources. An optical communication scheme is provided for initial programming, synchronization and re-programming after recovery from battery discharge. Standby power reduction techniques are investigated and a super cut-off power gating scheme with an ultra-low power charge pump reduces the standby power of logic circuits by 2-19× and memory by 30%. Different approaches for designing low-power memory for mm3-scale sensor nodes are also presented in this work. A dual threshold voltage gain cell eDRAM design achieves the lowest eDRAM retention power and a 7T SRAM design based on hetero-junction tunneling transistors reduces the standby power of SRAM by 9-19× with only 15% area overhead. We have paid special attention to the timer for the mm3-scale sensor systems and propose a multi-stage gate-leakage-based timer to limit the standard deviation of the error in hourly measurement to 196ms and a temperature compensation scheme reduces temperature dependency to 31ppm/°C. These techniques for designing ultra-low power circuits for a mm3-scale sensor enable implementation of a 1.0mm3 sensor node, which can be used as a skeleton for future micro-sensor systems in variety of applications. These microsystems imply the continuation of the Bell’s Law, which also predicts the massive deployment of mm3-scale computing systems and emergence of even smaller and more powerful computing systems in the near future.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/91438/1/sori_1.pd

Design and analysis of SRAMs for energy harvesting systems

PhD ThesisAt present, the battery is employed as a power source for wide varieties of microelectronic systems ranging from biomedical implants and sensor net-works to portable devices. However, the battery has several limitations and incurs many challenges for the majority of these systems. For instance, the design considerations of implantable devices concern about the battery from two aspects, the toxic materials it contains and its lifetime since replacing the battery means a surgical operation. Another challenge appears in wire-less sensor networks, where hundreds or thousands of nodes are scattered around the monitored environment and the battery of each node should be maintained and replaced regularly, nonetheless, the batteries in these nodes do not all run out at the same time. Since the introduction of portable systems, the area of low power designs has witnessed extensive research, driven by the industrial needs, towards the aim of extending the lives of batteries. Coincidentally, the continuing innovations in the field of micro-generators made their outputs in the same range of several portable applications. This overlap creates a clear oppor-tunity to develop new generations of electronic systems that can be powered, or at least augmented, by energy harvesters. Such self-powered systems benefit applications where maintaining and replacing batteries are impossi-ble, inconvenient, costly, or hazardous, in addition to decreasing the adverse effects the battery has on the environment. The main goal of this research study is to investigate energy harvesting aware design techniques for computational logic in order to enable the capa- II bility of working under non-deterministic energy sources. As a case study, the research concentrates on a vital part of all computational loads, SRAM, which occupies more than 90% of the chip area according to the ITRS re-ports. Essentially, this research conducted experiments to find out the design met-ric of an SRAM that is the most vulnerable to unpredictable energy sources, which has been confirmed to be the timing. Accordingly, the study proposed a truly self-timed SRAM that is realized based on complete handshaking protocols in the 6T bit-cell regulated by a fully Speed Independent (SI) tim-ing circuitry. The study proved the functionality of the proposed design in real silicon. Finally, the project enhanced other performance metrics of the self-timed SRAM concentrating on the bit-line length and the minimum operational voltage by employing several additional design techniques.Umm Al-Qura University, the Ministry of Higher Education in the Kingdom of Saudi Arabia, and the Saudi Cultural Burea

Low-power and high-performance SRAM design in high variability advanced CMOS technology

As process technologies shrink, the size and number of memories on a chip are exponentially increasing. Embedded SRAMs are a critical component in modern digital systems, and they strongly impact the overall power, performance, and area. To promote memory-related research in academia, this dissertation introduces OpenRAM, a flexible, portable and open-source memory compiler and characterization methodology for generating and verifying memory designs across different technologies.In addition, SRAM designs, focusing on improving power consumption, access time and bitcell stability are explored in high variability advanced CMOS technologies. To have a stable read/write operation for SRAM in high variability process nodes, a differential-ended single-port 8T bitcell is proposed that improves the read noise margin, write noise margin and readout bitcell current by 45%, 48% and 21%, respectively, compared to a conventional 6T bitcell. Also, a differential-ended single-port 12T bitcell for subthreshold operation is proposed that solves the half-select disturbance and allows efficient bit-interleaving. 12T bitcell has a leakage control mechanism which helps to reduce the power consumption and provides operation down to 0.3 V. Both 8T and 12T bitcells are analyzed in a 64 kb SRAM array using 32 nm technology. Besides, to further improve the access time and power consumption, two tracking circuits (multi replica bitline delay and reconfigurable replica bitline delay techniques) are proposed to aid the generation of accurate and optimum sense amplifier set time.An error tolerant SRAM architecture suitable for low voltage video application with dynamic power-quality management is also proposed in this dissertation. This memory uses three power supplies to improve the SRAM stability in low voltages. The proposed triple-supply approach achieves 63% improvement in image quality and 69% reduction in power consumption compared to a single-supply 64 kb SRAM array at 0.70 V

Very-Large-Scale-Integration Circuit Techniques in Internet-of-Things Applications

Heading towards the era of Internet-of-things (IoT) means both opportunity and challenge for the circuit-design community. In a system where billions of devices are equipped with the ability to sense, compute, communicate with each other and perform tasks in a coordinated manner, security and power management are among the most critical challenges. Physically unclonable function (PUF) emerges as an important security primitive in hardware-security applications; it provides an object-specific physical identifier hidden within the intrinsic device variations, which is hard to expose and reproduce by adversaries. Yet, designing a compact PUF robust to noise, temperature and voltage remains a challenge. This thesis presents a novel PUF design approach based on a pair of ultra-compact analog circuits whose output is proportional to absolute temperature. The proposed approach is demonstrated through two works: (1) an ultra-compact and robust PUF based on voltage-compensated proportional-to-absolute-temperature voltage generators that occupies 8.3× less area than the previous work with the similar robustness and twice the robustness of the previously most compact PUF design and (2) a technique to transform a 6T-SRAM array into a robust analog PUF with minimal overhead. In this work, similar circuit topology is used to transform a preexisting on-chip SRAM into a PUF, which further reduces the area in (1) with no robustness penalty. In this thesis, we also explore techniques for power management circuit design. Energy harvesting is an essential functionality in an IoT sensor node, where battery replacement is cost-prohibitive or impractical. Yet, existing energy-harvesting power management units (EH PMU) suffer from efficiency loss in the two-step voltage conversion: harvester-to-battery and battery-to-load. We propose an EH PMU architecture with hybrid energy storage, where a capacitor is introduced in addition to the battery to serve as an intermediate energy buffer to minimize the battery involvement in the system energy flow. Test-case measurements show as much as a 2.2× improvement in the end-to-end energy efficiency. In contrast, with the drastically reduced power consumption of IoT nodes that operates in the sub-threshold regime, adaptive dynamic voltage scaling (DVS) for supply-voltage margin removal, fully on-chip integration and high power conversion efficiency (PCE) are required in PMU designs. We present a PMU–load co-design based on a fully integrated switched-capacitor DC-DC converter (SC-DC) and hybrid error/replica-based regulation for a fully digital PMU control. The PMU is integrated with a neural spike processor (NSP) that achieves a record-low power consumption of 0.61 µW for 96 channels. A tunable replica circuit is added to assist the error regulation and prevent loss of regulation. With automatic energy-robustness co-optimization, the PMU can set the SC-DC’s optimal conversion ratio and switching frequency. The PMU achieves a PCE of 77.7% (72.2%) at VIN = 0.6 V (1 V) and at the NSP’s margin-free operating point

Algorithm/Architecture Co-Design for Low-Power Neuromorphic Computing

The development of computing systems based on the conventional von Neumann architecture has slowed down in the past decade as complementary metal-oxide-semiconductor (CMOS) technology scaling becomes more and more difficult. To satisfy the ever-increasing demands in computing power, neuromorphic computing has emerged as an attractive alternative. This dissertation focuses on developing learning algorithm, hardware architecture, circuit components, and design methodologies for low-power neuromorphic computing that can be employed in various energy-constrained applications. A top-down approach is adopted in this research. Starting from the algorithm-architecture co-design, a hardware-friendly learning algorithm is developed for spiking neural networks (SNNs). The possibility of estimating gradients from spike timings is explored. The learning algorithm is developed for the ease of hardware implementation, as well as the compatibility with many well-established learning techniques developed for classic artificial neural networks (ANNs). An SNN hardware equipped with the proposed on-chip learning algorithm is implemented in CMOS technology. In this design, two unique features of SNNs, the event-driven computation and the inferring with a progressive precision, are leveraged to reduce the energy consumption. In addition to low-power SNN hardware, accelerators for ANNs are also presented to accelerate the adaptive dynamic programing algorithm. An efficient and flexible single-instruction-multiple-data architecture is proposed to exploit the inherent data-level parallelism in the inference and learning of ANNs. In addition, the accelerator is augmented with a virtual update technique, which helps improve the throughput and energy efficiency remarkably. Lastly, two techniques in the architecture-circuit level are introduced to mitigate the degraded reliability of the memory system in a neuromorphic hardware owing to the aggressively-scaled supply voltage and integration density. The first method uses on-chip feedback to compensate for the process variation and the second technique improves the throughput and energy efficiency of a conventional error-correction method.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/144149/1/zhengn_1.pd

Low energy digital circuit design using sub-threshold operation

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, February 2006.Includes bibliographical references (p. 189-202).Scaling of process technologies to deep sub-micron dimensions has made power management a significant concern for circuit designers. For emerging low power applications such as distributed micro-sensor networks or medical applications, low energy operation is the primary concern instead of speed, with the eventual goal of harvesting energy from the environment. Sub-threshold operation offers a promising solution for ultra-low-energy applications because it often achieves the minimum energy per operation. While initial explorations into sub-threshold circuits demonstrate its promise, sub-threshold circuit design remains in its infancy. This thesis makes several contributions that make sub-threshold design more accessible to circuit designers. First, a model for energy consumption in sub-threshold provides an analytical solution for the optimum VDD to minimize energy. Fitting this model to a generic circuit allows easy estimation of the impact of processing and environmental parameters on the minimum energy point. Second, analysis of device sizing for sub-threshold circuits shows the trade-offs between sizing for minimum energy and for minimum voltage operation.(cont.) A programmable FIR filter test chip fabricated in 0.18pum bulk CMOS provides measurements to confirm the model and the sizing analysis. Third, a low-overhead method for integrating sub-threshold operation with high performance applications extends dynamic voltage scaling across orders of magnitude of frequency and provides energy scalability down to the minimum energy point. A 90nm bulk CMOS test chip confirms the range of operation for ultra-dynamic voltage scaling. Finally, sub-threshold operation is extended to memories. Analysis of traditional SRAM bitcells and architectures leads to development of a new bitcell for robust sub-threshold SRAM operation. The sub-threshold SRAM is analyzed experimentally in a 65nm bulk CMOS test chip.by Benton H. Calhoun.Ph.D

Solid State Circuits Technologies

The evolution of solid-state circuit technology has a long history within a relatively short period of time. This technology has lead to the modern information society that connects us and tools, a large market, and many types of products and applications. The solid-state circuit technology continuously evolves via breakthroughs and improvements every year. This book is devoted to review and present novel approaches for some of the main issues involved in this exciting and vigorous technology. The book is composed of 22 chapters, written by authors coming from 30 different institutions located in 12 different countries throughout the Americas, Asia and Europe. Thus, reflecting the wide international contribution to the book. The broad range of subjects presented in the book offers a general overview of the main issues in modern solid-state circuit technology. Furthermore, the book offers an in depth analysis on specific subjects for specialists. We believe the book is of great scientific and educational value for many readers. I am profoundly indebted to the support provided by all of those involved in the work. First and foremost I would like to acknowledge and thank the authors who worked hard and generously agreed to share their results and knowledge. Second I would like to express my gratitude to the Intech team that invited me to edit the book and give me their full support and a fruitful experience while working together to combine this book

Single event upset mitigation in low power SRAM design

Logic compatible gain cell (GC)-embedded DRAM (eDRAM) arrays are considered an alternative to SRAM due to their small size, nonratioed operation, low static leakage, and two-port functionality. However, traditional GC-eDRAM implementations require boosted control signals in order to write full voltage levels to the cell to reduce the refresh rate and shorten access times. These boosted levels require either an extra power supply or on-chip charge pumps, as well as nontrivial level shifting and toleration of high voltage levels. In this brief, we present a novel, logic compatible, 3T GC-eDRAM bitcell that operates with a single-supply voltage and provides superior write capability to the conventional GC structures. The proposed circuit is demonstrated with a 2-kb memory macro that was designed and fabricated in a mature 0.18-μm CMOS process, targeted at low-power, energy-efficient applications. The test array is powered with a single supply of 900 mV, showing a 0.8-ms worst case retention time, a 1.3-ns write-access time, and a 2.4-pW/bit retention power. The proposed topology provides a bitcell area reduction of 43%, as compared with a redrawn 6-transistor SRAM in the same technology, and an overall macro area reduction of 67% including peripherals