Dual Mode Suspended Substrate Stripline (SSS) Filter

Evolution of wireless communication systems towards high flexibility, low cost and high efficiency leads to tremendous activity in the area of microwave filters. In an RF front-end of a cellular radio base station, signals are being transmitted and received simultaneously. In the receive band, there are chances of intermodulation products from the power amplifier being fed to the receiver,thus the transmit filter must have a very high level of signal rejection. Furthermore, the transmit filter must also have low passband insertion loss since it impacts the power transmitted and the overall transmit system efficiency. Recently, filters with dual-mode operation were being investigated due to their ability to produce two degenerate modes using a single physical structure; therefore, the size and cost of the filter can be reduced without compromising any figure-of-merits. A dual mode suspended substrate stripline filter is presented in this thesis. These filters enable achieving low insertion loss, high Q, high selectivity and good spurious response. Initially, a dual mode ring resonator structure is investigated using suspended substrate stripline technology. This technology is used due to its advantages which are comparable to microstrip or any other planar transmission lines. The HFSS three dimensional finite element method (FEM) is used to evaluate the resonant frequency, quality factor and the first harmonics.A second order suspended substrate stripline filter was designed with capacitive coupled input and output feeding method. The input and output feed were positioned 90 degree from each other while a notch was used in this filter to couple two degenerate modes which also control the bandwidth of the filter. A high performance Generalized Chebychev filter was designed to meet the stringent electrical requirement in the RF front-end of a cellular radio base station. With this fourth order filter, four finite frequency transmission zeros were achieved due to phase cancellation between two paths which results in high selectivity filter response. Metal tuning screws were added to improve any practical imperfections. Finally an asymmetrical Generalized Chebychev filter was designed with real frequency transmission zeros positioned on one side of the passband. With this design, the aim of achieving higher selectivity filter response above the passband was demonstrated

Wideband and UWB antennas for wireless applications. A comprehensive review

A comprehensive review concerning the geometry, the manufacturing technologies, the materials, and the numerical techniques, adopted for the analysis and design of wideband and ultrawideband (UWB) antennas for wireless applications, is presented. Planar, printed, dielectric, and wearable antennas, achievable on laminate (rigid and flexible), and textile dielectric substrates are taken into account. The performances of small, low-profile, and dielectric resonator antennas are illustrated paying particular attention to the application areas concerning portable devices (mobile phones, tablets, glasses, laptops, wearable computers, etc.) and radio base stations. This information provides a guidance to the selection of the different antenna geometries in terms of bandwidth, gain, field polarization, time-domain response, dimensions, and materials useful for their realization and integration in modern communication systems

Development of planar filters and diplexers for wireless transceiver front ends

The central theme of this work is the design of compact microstrip bandpass filters and diplexers and the investigation of applications of these circuits in integrated transceiver RF front-end. The core of this thesis therefore presents the following stages of the work: - Analysis of coupled pseudo-interdigital resonators and lines; formulation of approximate transmission zero conditions and the investigation of coupling between these two resonators and related structures. - Development of compact, low loss and high selectivity microstrip pseudointerdigital bandpass filters. The design procedure of the filter consists of three simple steps, starting from the design of a parallel-coupled bandpass filter using the image parameter method applied to coupled microstrip lines. The development of compact microstrip diplexers composed of these filters uses the optimized common-transformer diplexing technique. An experimental verification of the developed filters and diplexers is made. - Investigation of the use of stepped impedance resonators (SIR) for the design of pseudo-interdigital bandpass filters with advanced characteristics. The design of compact dual-band filter using SIR. The investigation of possible improvement of the stopband of bandpass filters using bandstop generating structures. The application of SIR, defected ground structures (DGS), spur-lines, and opencircuited stubs in the design of compact bandpass filters with improved stopband. - The application of the proposed filters and diplexers in the design of integrated antenna filters and antenna diplexers. Improvement of performance of patch antennas, such as suppression of spurious harmonics of single-band antenna and improvement of bandwidth and selectivity of dual-band antenna, as a result of integration with filters. Separation of antennas’ bands and reduction of component count in integrated antenna diplexer

UWB Technology

Ultra Wide Band (UWB) technology has attracted increasing interest and there is a growing demand for UWB for several applications and scenarios. The unlicensed use of the UWB spectrum has been regulated by the Federal Communications Commission (FCC) since the early 2000s. The main concern in designing UWB circuits is to consider the assigned bandwidth and the low power permitted for transmission. This makes UWB circuit design a challenging mission in today's community. Various circuit designs and system implementations are published in this book to give the reader a glimpse of the state-of-the-art examples in this field. The book starts at the circuit level design of major UWB elements such as filters, antennas, and amplifiers; and ends with the complete system implementation using such modules

A COMPREHENSIVE OVERVIEW OF RECENT DEVELOPMENTS IN RF-MEMS TECHNOLOGY-BASED HIGH-PERFORMANCE PASSIVE COMPONENTS FOR APPLICATIONS IN THE 5G AND FUTURE TELECOMMUNICATIONS SCENARIOS

The goal of this work is to provide an overview about the current development of radio-frequency microelectromechanical systems technology, with special attention towards those passive components bearing significant application potential in the currently developing 5G paradigm. Due to the required capabilities of such communication standard in terms of high data rates, extended allocated spectrum, use of massive MIMO (Multiple-Input-Multiple-Output) systems, beam steering and beam forming, the focus will be on devices like switches, phase shifters, attenuators, filters, and their packaging/integration. For each of the previous topics, several valuable contributions appeared in the last decade, underlining the improvements produced in the state of the art and the chance for RF-MEMS technology to play a prominent role in the actual implementation of the 5G infrastructure

Compact Microstrip Triple-Mode Bandpass Filters Using Dual-Stub-Loaded Spiral Resonators

Two new microstrip triple-mode resonators loaded with T-shaped open stubs using axially and centrally symmetric spiral structures, respectively, are presented. Spiraled for circuit size reduction, these two half-wavelength resonators can both generate three resonant modes over a wide frequency band by loading two T-stubs with different lengths. Due to the structural symmetry, they can be analyzed by odd- and even-mode method. To validate the design concept, two compact bandpass filters (BPFs) using these two novel resonators with center frequencies of 1.76 GHz and 2.44 GHz for the GSM1800 and WLAN/Zigbee applications, respectively, have been designed, fabricated and tested. The center frequencies and bandwidths can be tunable through the analysis of resonant frequency responses, fractional bandwidths and external quality factor versus the resonator parameters. The final measured results have achieved good consistence with the simulations of these two BPFs

Metamaterial

In-depth analysis of the theory, properties and description of the most potential technological applications of metamaterials for the realization of novel devices such as subwavelength lenses, invisibility cloaks, dipole and reflector antennas, high frequency telecommunications, new designs of bandpass filters, absorbers and concentrators of EM waves etc. In order to create a new devices it is necessary to know the main electrodynamical characteristics of metamaterial structures on the basis of which the device is supposed to be created. The electromagnetic wave scattering surfaces built with metamaterials are primarily based on the ability of metamaterials to control the surrounded electromagnetic fields by varying their permeability and permittivity characteristics. The book covers some solutions for microwave wavelength scales as well as exploitation of nanoscale EM wavelength such as visible specter using recent advances of nanotechnology, for instance in the field of nanowires, nanopolymers, carbon nanotubes and graphene. Metamaterial is suitable for scholars from extremely large scientific domain and therefore given to engineers, scientists, graduates and other interested professionals from photonics to nanoscience and from material science to antenna engineering as a comprehensive reference on this artificial materials of tomorrow

Novel miniature microwave quasi-elliptical function bandpass filters with wideband harmonic suppression

Filters are integral components in all wireless communication systems, and their function is to permit predefined band of frequencies into the system and reject all other signals. The ever-growing demand in the use of the radio frequency (RF) spectrum for new applications has resulted in the need for high performance microwave filters with strict requirements on both inband and out-of-band characteristics. High selectivity, high rejection, low loss and extremely wide spurious-free performance are required for both transmitter and receiver channels. In addition, these devices need to be highly compact, easy to integrate within transceivers and should be amenable to low cost manufacturing. High selectivity is essential to enable the guard band between adjacent channels to be reduced thus improving the efficiency of the RF spectrum and hence increasing the capacity of the system. A low insertion-loss, high return-loss and small group-delay in the passband are necessary to minimize signal degradation. A wide stopband is necessary to suppress spurious passbands outside the filter’s bandwidth that may allow spurious emissions from modulation process (harmonic, parasitic, intermodulation and frequency conversion products) and interfere with other systems. The EMC Directive 89/336/EEC mandates that all electronic equipment must comply with the applicable EN specification for EMI. This thesis presents the research work that has resulted in the development of innovative and compact microstrip bandpass filters that fulfil the above stringent requirements for wireless communication systems. In fact, the proposed highly compact planar microstrip filters provide an alternative solution for existing and next generation of wireless communications systems. In particular, the proposed filters exhibit a low-loss and quasi-elliptic function response that is normally only possible with filter designs using waveguides and high temperature superconductors. The selectivity of the filters has been improved by inserting a pair of transmission zeros between the passband edges, and implementing notched rejection bands in the filter’s frequency response to widen its stopband performance. The filter structures have been analysed theoretically and modelled by using Keysight Technologies’ Advanced Design System (ADS™) and Momentum® software. The dissertation is essentially composed of four main sections. In the first section, several compact and quasi-elliptic function bandpass filter structures are proposed and theoretically analysed. Selectivity and stopband performance of these filters is enhanced by loading the input and output feed-lines with inductive stubs that introduce transmission zeros at specified frequencies in the filter’s frequency response. This technique is shown to provide a sharp 3-dB roll-off and steep selectivity skirt with high out-of-band rejection over a wide frequency span. In addition, the 3-dB fractional bandwidth of the filters is shown to be controllable by manipulating the filter’s geometric parameters. Traditional microwave bandpass filters are designed using quarter-wavelength distributed transmission-line resonators that are either end-coupled or side-coupled. The sharpness of the filter response is determined by the number of resonators employed which degrades the filter’s passband loss performance. This results in a filter with a significantly larger footprint which precludes miniaturization. To circumvent these drawbacks the second section describes the development of a novel and compact wideband bandpass filter with the desired characteristics. The quasi-elliptic function filter comprises open-loop resonators that are coupled to each other using a stub loaded resonator. The proposed filter is shown to achieve a wideband 3-dB fractional bandwidth of 23% with much better loss performance, sharp skirt selectivity and very wide rejection bandwidth. The third section describes the investigation of novel ultra-wideband (UWB) microstrip bandpass filter designs. Parametric study enabled the optimization of the filter’s performance which was verified through practical measurements. The proposed filters meet the stringent characteristics required by modern communications systems, i.e. the filters are highly compact and miniature even when fabricated on a low dielectric constant substrate, possess a sharp quasi-elliptic function bandpass response with low passband insertion-loss, and ultra-wide stopband performance. With the rapid development of multi-band operation in modern and next generation wireless communication systems, there is a great demand for single frequency discriminating devices that can operate over multiple frequency bands to facilitate miniaturization. These multi-band bandpass filters need to be physically small, have low insertion-loss, high return-loss, and excellent selectivity. In the fourth section two miniature microstrip dual-band and triple-band bandpass filter designs are explored. A detailed parametric study was conducted to fully understand how the geometric parameters of the filters affected their performance. The optimized filters were fabricated and measured to validate their performance