Design and modelling of variability tolerant on-chip communication structures for future high performance system on chip designs

The incessant technology scaling has enabled the integration of functionally complex System-on-Chip (SoC) designs with a large number of heterogeneous systems on a single chip. The processing elements on these chips are integrated through on-chip communication structures which provide the infrastructure necessary for the exchange of data and control signals, while meeting the strenuous physical and design constraints. The use of vast amounts of on chip communications will be central to future designs where variability is an inherent characteristic. For this reason, in this thesis we investigate the performance and variability tolerance of typical on-chip communication structures. Understanding of the relationship between variability and communication is paramount for the designers; i.e. to devise new methods and techniques for designing performance and power efficient communication circuits in the forefront of challenges presented by deep sub-micron (DSM) technologies. The initial part of this work investigates the impact of device variability due to Random Dopant Fluctuations (RDF) on the timing characteristics of basic communication elements. The characterization data so obtained can be used to estimate the performance and failure probability of simple links through the methodology proposed in this work. For the Statistical Static Timing Analysis (SSTA) of larger circuits, a method for accurate estimation of the probability density functions of different circuit parameters is proposed. Moreover, its significance on pipelined circuits is highlighted. Power and area are one of the most important design metrics for any integrated circuit (IC) design. This thesis emphasises the consideration of communication reliability while optimizing for power and area. A methodology has been proposed for the simultaneous optimization of performance, area, power and delay variability for a repeater inserted interconnect. Similarly for multi-bit parallel links, bandwidth driven optimizations have also been performed. Power and area efficient semi-serial links, less vulnerable to delay variations than the corresponding fully parallel links are introduced. Furthermore, due to technology scaling, the coupling noise between the link lines has become an important issue. With ever decreasing supply voltages, and the corresponding reduction in noise margins, severe challenges are introduced for performing timing verification in the presence of variability. For this reason an accurate model for crosstalk noise in an interconnection as a function of time and skew is introduced in this work. This model can be used for the identification of skew condition that gives maximum delay noise, and also for efficient design verification

Physical Design and Clock Tree Synthesis Methods For A 8-Bit Processor

Now days a number of processors are available with a lot kind of feature from different industries. A processor with similar kind of architecture of the current processors only missing the memory stuffs like the RAM and ROM has been designed here with the help of Verilog style of coding. This processor contains architecturally the program counter, instruction register, ALU, ALU latch, General Purpose Registers, control state module, flag registers and the core module containing all the modules. And a test module is designed for testing the processor. After the design of the processor with successful functionality, the processor is synthesized with 180nm technology. The synthesis is performed with the data path optimization like the selection of proper adders and multipliers for timing optimization in the data path while the ALU operations are performed. During synthesis how to take care of the worst negative slack (WNS), how to include the clock gating cells, how to define the cost and path groups etc. have been covered. After the proper synthesis we get the proper net list and the synthesized constraint file for carrying out the physical design. In physical design the steps like floor-planning, partitioning, placement, legalization of the placement, clock tree synthesis, and routing etc. have been performed. At all the stages the static timing analysis is performed for the timing meet of the design for better performance in terms of timing or frequency. Each steps of physical design are discussed with special effort towards the concepts behind the step. Out of all the steps of physical design the clock tree synthesis is performed with some improvement in the performance of the clock tree by creating a symmetrical clock tree and maintaining more common clock paths. A special algorithm has been framed for creating a symmetrical clock tree and thereby making the power consumption of the clock tree low

Communication Reliability in Network on Chip Designs

The performance of low latency Network on Chip (NoC) architectures, which incorporate fast bypass paths to reduce communication latency, is limited by crosstalk induced skewing of signal transitions on link wires. As a result of crosstalk interactions between wires, signal transitions belonging to the same flit or bit vector arrive at the destination at different times and are likely to violate setup and hold time constraints for the design. This thesis proposes a two-step technique: TransSync- RecSync, to dynamically eliminate packet errors resulting from inter-bit-line transition skew. The proposed approach adds minimally to router complexity and involves no wire overhead. The actual throughput of NoC designs with asynchronous bypass designs is evaluated and the benefits of augmenting such schemes with the proposed design are studied. The TransSync, TransSync-2-lines and RecSync schemes described here are found to improve the average communication latency by 26%, 20% and 38% respectively in a 7X7 mesh NoC with asynchronous bypass channel. This work also evaluates the bit-error ratio (BER) performance of several existing crosstalk avoidance and error correcting schemes and compares them to that of the proposed schemes. Both TransSync and RecSync scheme are dynamic in nature and can be switched on and off on-the-fly. The proposed schemes can therefore be employed to impart unequal error protection (UEP) against intra-flit skewing on NoC links. In the UEP, a larger fraction of the energy budget is spent in providing protection to those parts of the data being transmitted on the link which have a higher priority, while expending smaller effort in protecting relatively less important parts of the data. This allows us to achieve the prescribed level of performance with lower levels of power. The benefits of the presented technique are illustrated using an H.264 video decoder system-on-chip (SoC) employing NoC architecture. We show that for Akyio test streams transmitted over 3mm long link wires, the power consumption can be reduced by as much as 20% at the cost of an acceptable degradation in average peak signal to noise ratio (PSNR) with UEP

High-Speed and Low-Energy On-Chip Communication Circuits.

Continuous technology scaling sharply reduces transistor delays, while fixed-length global wire delays have increased due to less wiring pitch with higher resistance and coupling capacitance. Due to this ever growing gap, long on-chip interconnects pose well-known latency, bandwidth, and energy challenges to high-performance VLSI systems. Repeaters effectively mitigate wire RC effects but do little to improve their energy costs. Moreover, the increased complexity and high level of integration requires higher wire densities, worsening crosstalk noise and power consumption of conventionally repeated interconnects. Such increasing concerns in global on-chip wires motivate circuits to improve wire performance and energy while reducing the number of repeaters. This work presents circuit techniques and investigation for high-performance and energy-efficient on-chip communication in the aspects of encoding, data compression, self-timed current injection, signal pre-emphasis, low-swing signaling, and technology mapping. The improved bus designs also consider the constraints of robust operation and performance/energy gains across process corners and design space. Measurement results from 5mm links on 65nm and 90nm prototype chips validate 2.5-3X improvement in energy-delay product.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/75800/1/jseo_1.pd

Low Power Processor Architectures and Contemporary Techniques for Power Optimization – A Review

The technological evolution has increased the number of transistors for a given die area significantly and increased the switching speed from few MHz to GHz range. Such inversely proportional decline in size and boost in performance consequently demands shrinking of supply voltage and effective power dissipation in chips with millions of transistors. This has triggered substantial amount of research in power reduction techniques into almost every aspect of the chip and particularly the processor cores contained in the chip. This paper presents an overview of techniques for achieving the power efficiency mainly at the processor core level but also visits related domains such as buses and memories. There are various processor parameters and features such as supply voltage, clock frequency, cache and pipelining which can be optimized to reduce the power consumption of the processor. This paper discusses various ways in which these parameters can be optimized. Also, emerging power efficient processor architectures are overviewed and research activities are discussed which should help reader identify how these factors in a processor contribute to power consumption. Some of these concepts have been already established whereas others are still active research areas. © 2009 ACADEMY PUBLISHER

Low-Power Embedded Design Solutions and Low-Latency On-Chip Interconnect Architecture for System-On-Chip Design

This dissertation presents three design solutions to support several key system-on-chip (SoC) issues to achieve low-power and high performance. These are: 1) joint source and channel decoding (JSCD) schemes for low-power SoCs used in portable multimedia systems, 2) efficient on-chip interconnect architecture for massive multimedia data streaming on multiprocessor SoCs (MPSoCs), and 3) data processing architecture for low-power SoCs in distributed sensor network (DSS) systems and its implementation. The first part includes a low-power embedded low density parity check code (LDPC) - H.264 joint decoding architecture to lower the baseband energy consumption of a channel decoder using joint source decoding and dynamic voltage and frequency scaling (DVFS). A low-power multiple-input multiple-output (MIMO) and H.264 video joint detector/decoder design that minimizes energy for portable, wireless embedded systems is also designed. In the second part, a link-level quality of service (QoS) scheme using unequal error protection (UEP) for low-power network-on-chip (NoC) and low latency on-chip network designs for MPSoCs is proposed. This part contains WaveSync, a low-latency focused network-on-chip architecture for globally-asynchronous locally-synchronous (GALS) designs and a simultaneous dual-path routing (SDPR) scheme utilizing path diversity present in typical mesh topology network-on-chips. SDPR is akin to having a higher link width but without the significant hardware overhead associated with simple bus width scaling. The last part shows data processing unit designs for embedded SoCs. We propose a data processing and control logic design for a new radiation detection sensor system generating data at or above Peta-bits-per-second level. Implementation results show that the intended clock rate is achieved within the power target of less than 200mW. We also present a digital signal processing (DSP) accelerator supporting configurable MAC, FFT, FIR, and 3-D cross product operations for embedded SoCs. It consumes 12.35mW along with 0.167mm2 area at 333MHz

Network-on-Chip

Addresses the Challenges Associated with System-on-Chip Integration Network-on-Chip: The Next Generation of System-on-Chip Integration examines the current issues restricting chip-on-chip communication efficiency, and explores Network-on-chip (NoC), a promising alternative that equips designers with the capability to produce a scalable, reusable, and high-performance communication backbone by allowing for the integration of a large number of cores on a single system-on-chip (SoC). This book provides a basic overview of topics associated with NoC-based design: communication infrastructure design, communication methodology, evaluation framework, and mapping of applications onto NoC. It details the design and evaluation of different proposed NoC structures, low-power techniques, signal integrity and reliability issues, application mapping, testing, and future trends. Utilizing examples of chips that have been implemented in industry and academia, this text presents the full architectural design of components verified through implementation in industrial CAD tools. It describes NoC research and developments, incorporates theoretical proofs strengthening the analysis procedures, and includes algorithms used in NoC design and synthesis. In addition, it considers other upcoming NoC issues, such as low-power NoC design, signal integrity issues, NoC testing, reconfiguration, synthesis, and 3-D NoC design. This text comprises 12 chapters and covers: The evolution of NoC from SoC—its research and developmental challenges NoC protocols, elaborating flow control, available network topologies, routing mechanisms, fault tolerance, quality-of-service support, and the design of network interfaces The router design strategies followed in NoCs The evaluation mechanism of NoC architectures The application mapping strategies followed in NoCs Low-power design techniques specifically followed in NoCs The signal integrity and reliability issues of NoC The details of NoC testing strategies reported so far The problem of synthesizing application-specific NoCs Reconfigurable NoC design issues Direction of future research and development in the field of NoC Network-on-Chip: The Next Generation of System-on-Chip Integration covers the basic topics, technology, and future trends relevant to NoC-based design, and can be used by engineers, students, and researchers and other industry professionals interested in computer architecture, embedded systems, and parallel/distributed systems

Doctor of Philosophy

dissertationCommunication surpasses computation as the power and performance bottleneck in forthcoming exascale processors. Scaling has made transistors cheap, but on-chip wires have grown more expensive, both in terms of latency as well as energy. Therefore, the need for low energy, high performance interconnects is highly pronounced, especially for long distance communication. In this work, we examine two aspects of the global signaling problem. The first part of the thesis focuses on a high bandwidth asynchronous signaling protocol for long distance communication. Asynchrony among intellectual property (IP) cores on a chip has become necessary in a System on Chip (SoC) environment. Traditional asynchronous handshaking protocol suffers from loss of throughput due to the added latency of sending the acknowledge signal back to the sender. We demonstrate a method that supports end-to-end communication across links with arbitrarily large latency, without limiting the bandwidth, so long as line variation can be reliably controlled. We also evaluate the energy and latency improvements as a result of the design choices made available by this protocol. The use of transmission lines as a physical interconnect medium shows promise for deep submicron technologies. In our evaluations, we notice a lower energy footprint, as well as vastly reduced wire latency for transmission line interconnects. We approach this problem from two sides. Using field solvers, we investigate the physical design choices to determine the optimal way to implement these lines for a given back-end-of-line (BEOL) stack. We also approach the problem from a system designer's viewpoint, looking at ways to optimize the lines for different performance targets. This work analyzes the advantages and pitfalls of implementing asynchronous channel protocols for communication over long distances. Finally, the innovations resulting from this work are applied to a network-on-chip design example and the resulting power-performance benefits are reported

차세대 HBM 용 고집적, 저전력 송수신기 설계

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2020. 8. 정덕균.This thesis presents design techniques for high-density power-efficient transceiver for the next-generation high bandwidth memory (HBM). Unlike the other memory interfaces, HBM uses a 3D-stacked package using through-silicon via (TSV) and a silicon interposer. The transceiver for HBM should be able to solve the problems caused by the 3D-stacked package and TSV. At first, a data (DQ) receiver for HBM with a self-tracking loop that tracks a phase skew between DQ and data strobe (DQS) due to a voltage or thermal drift is proposed. The self-tracking loop achieves low power and small area by uti-lizing an analog-assisted baud-rate phase detector. The proposed pulse-to-charge (PC) phase detector (PD) converts the phase skew to a voltage differ-ence and detects the phase skew from the voltage difference. An offset calibra-tion scheme that can compensates for a mismatch of the PD is also proposed. The proposed calibration scheme operates without any additional sensing cir-cuits by taking advantage of the write training of HBM. Fabricated in 65 nm CMOS, the DQ receiver shows a power efficiency of 370 fJ/b at 4.8 Gb/s and occupies 0.0056 mm2. The experimental results show that the DQ receiver op-erates without any performance degradation under a ± 10% supply variation. In a second prototype IC, a high-density transceiver for HBM with a feed-forward-equalizer (FFE)-combined crosstalk (XT) cancellation scheme is pre-sented. To compensate for the XT, the transmitter pre-distorts the amplitude of the FFE output according to the XT. Since the proposed XT cancellation (XTC) scheme reuses the FFE implemented to equalize the channel loss, additional circuits for the XTC is minimized. Thanks to the XTC scheme, a channel pitch can be significantly reduced, allowing for the high channel density. Moreover, the 3D-staggered channel structure removes the ground layer between the verti-cally adjacent channels, which further reduces a cross-sectional area of the channel per lane. The test chip including 6 data lanes is fabricated in 65 nm CMOS technology. The 6-mm channels are implemented on chip to emulate the silicon interposer between the HBM and the processor. The operation of the XTC scheme is verified by simultaneously transmitting 4-Gb/s data to the 6 consecutive channels with 0.5-um pitch and the XTC scheme reduces the XT-induced jitter up to 78 %. The measurement result shows that the transceiver achieves the throughput of 8 Gb/s/um. The transceiver occupies 0.05 mm2 for 6 lanes and consumes 36.6 mW at 6 x 4 Gb/s.본 논문에서는 차세대 HBM을 위한 고집적 저전력 송수신기 설계 방법을 제안한다. 첫 번째로, 전압 및 온도 변화에 의한 데이터와 클럭 간 위상 차이를 보상할 수 있는 자체 추적 루프를 가진 데이터 수신기를 제안한다. 제안하는 자체 추적 루프는 데이터 전송 속도와 같은 속도로 동작하는 위상 검출기를 사용하여 전력 소모와 면적을 줄였다. 또한 메모리의 쓰기 훈련 (write training) 과정을 이용하여 효과적으로 위상 검출기의 오프셋을 보상할 수 있는 방법을 제안한다. 제안하는 데이터 수신기는 65 nm 공정으로 제작되어 4.8 Gb/s에서 370 fJ/b을 소모하였다. 또한 10 % 의 전압 변화에 대하여 안정적으로 동작하는 것을 확인하였다. 두 번째로, 피드 포워드 이퀄라이저와 결합된 크로스 토크 보상 방식을 활용한 고집적 송수신기를 제안한다. 제안하는 송신기는 크로스 토크 크기에 해당하는 만큼 송신기 출력을 왜곡하여 크로스 토크를 보상한다. 제안하는 크로스 토크 보상 방식은 채널 손실을 보상하기 위해 구현된 피드 포워드 이퀄라이저를 재활용함으로써 추가적인 회로를 최소화한다. 제안하는 송수신기는 크로스 토크가 보상 가능하기 때문에, 채널 간격을 크게 줄여 고집적 통신을 구현하였다. 또한 집적도를 더 증가시키기 위해 세로로 인접한 채널 사이의 차폐 층을 제거한 적층 채널 구조를 제안한다. 6개의 송수신기를 포함한 프로토타입 칩은 65 nm 공정으로 제작되었다. HBM과 프로세서 사이의 silicon interposer channel 을 모사하기 위한 6 mm 의 채널이 칩 위에 구현되었다. 제안하는 크로스 토크 보상 방식은 0.5 um 간격의 6개의 인접한 채널에 동시에 데이터를 전송하여 검증되었으며, 크로스 토크로 인한 지터를 최대 78 % 감소시켰다. 제안하는 송수신기는 8 Gb/s/um 의 처리량을 가지며 6 개의 송수신기가 총 36.6 mW의 전력을 소모하였다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 4 CHAPTER 2 BACKGROUND ON HIGH-BANDWIDTH MEMORY 6 2.1 OVERVIEW 6 2.2 TRANSCEIVER ARCHITECTURE 10 2.3 READ/WRITE OPERATION 15 2.3.1 READ OPERATION 15 2.3.2 WRITE OPERATION 19 CHAPTER 3 BACKGROUNDS ON COUPLED WIRES 21 3.1 GENERALIZED MODEL 21 3.2 EFFECT OF CROSSTALK 26 CHAPTER 4 DQ RECEIVER WITH BAUD-RATE SELF-TRACKING LOOP 29 4.1 OVERVIEW 29 4.2 FEATURES OF DQ RECEIVER FOR HBM 33 4.3 PROPOSED PULSE-TO-CHARGE PHASE DETECTOR 35 4.3.1 OPERATION OF PULSE-TO-CHARGE PHASE DETECTOR 35 4.3.2 OFFSET CALIBRATION 37 4.3.3 OPERATION SEQUENCE 39 4.4 CIRCUIT IMPLEMENTATION 42 4.5 MEASUREMENT RESULT 46 CHAPTER 5 HIGH-DENSITY TRANSCEIVER FOR HBM WITH 3D-STAGGERED CHANNEL AND CROSSTALK CANCELLATION SCHEME 57 5.1 OVERVIEW 57 5.2 PROPOSED 3D-STAGGERED CHANNEL 61 5.2.1 IMPLEMENTATION OF 3D-STAGGERED CHANNEL 61 5.2.2 CHANNEL CHARACTERISTICS AND MODELING 66 5.3 PROPOSED FEED-FORWARD-EQUALIZER-COMBINED CROSSTALK CANCELLATION SCHEME 72 5.4 CIRCUIT IMPLEMENTATION 77 5.4.1 OVERALL ARCHITECTURE 77 5.4.2 TRANSMITTER WITH FFE-COMBINED XTC 79 5.4.3 RECEIVER 81 5.5 MEASUREMENT RESULT 82 CHAPTER 6 CONCLUSION 93 BIBLIOGRAPHY 95 초 록 102Docto

Physical design of USB1.1

In earlier days, interfacing peripheral devices to host computer has a big problematic. There existed so many different kinds’ ports like serial port, parallel port, PS/2 etc. And their use restricts many situations, Such as no hot-pluggability and involuntary configuration. There are very less number of methods to connect the peripheral devices to host computer. The main reason that Universal Serial Bus was implemented to provide an additional benefits compared to earlier interfacing ports. USB is designed to allow many peripheral be connecting using single standardize interface. It provides an expandable fast, cost effective, hot-pluggable plug and play serial hardware interface that makes life of computer user easier allowing them to plug different devices to into USB port and have them configured automatically. In this thesis demonstrated the USB v1.1 architecture part in briefly and generated gate level net list form RTL code by applying the different constraints like timing, area and power. By applying the various types design constraints so that the performance was improved by 30%. And then it implemented in physically by using SoC encounter EDI system, estimation of chip size, power analysis and routing the clock signal to all flip-flops presented in the design. To reduce the clock switching power implemented register clustering algorithm (DBSCAN). In this design implementation TSMC 180nm technology library is used