LOT: Logic Optimization with Testability - new transformations for logic synthesis

A new approach to optimize multilevel logic circuits is introduced. Given a multilevel circuit, the synthesis method optimizes its area while simultaneously enhancing its random pattern testability. The method is based on structural transformations at the gate level. New transformations involving EX-OR gates as well as Reed–Muller expansions have been introduced in the synthesis of multilevel circuits. This method is augmented with transformations that specifically enhance random-pattern testability while reducing the area. Testability enhancement is an integral part of our synthesis methodology. Experimental results show that the proposed methodology not only can achieve lower area than other similar tools, but that it achieves better testability compared to available testability enhancement tools such as tstfx. Specifically for ISCAS-85 benchmark circuits, it was observed that EX-OR gate-based transformations successfully contributed toward generating smaller circuits compared to other state-of-the-art logic optimization tools

A Novel Reseeding Mechanism for Improving Pseudo-Random Testing of VLSI Circuits

[[abstract]]During built-in self-test (BIST), the set of patterns generated by a pseudo-random pattern generator may not provide sufficiently high fault coverage and many patterns can't detect fault (called useless patterns). In order to reduce the test time, we can remove useless patterns or change them to useful patterns (fault dropping). In fact, a random test set includes many useless patterns. Therefore we present a technology, including both reseeding and bit modifying (a.k.a. pattern mapping) to remove useless patterns or change them to useful patterns. When patterns changed, we pick out number of different fewer bits, leading to very short test length. Then we use an additional bit counter to improve test length and achieve high fault coverage. The technique we present is applicable for single-stuck-at faults. Experimental results indicate that complete fault coverage-100% can be obtained with less test time.[[notice]]補正完畢[[journaltype]]國際[[incitationindex]]EI[[ispeerreviewed]]Y[[booktype]]紙本[[countrycodes]]TW

A novel reseeding mechanism for pseudo-random testing of VLSI circuits

[[abstract]]During built-in self-test (BIST), the set of patterns generated by a pseudo-random pattern generator may not provide sufficiently high fault coverage and many patterns were undetected fault (useless patterns). In order to reduce the test time, we can remove useless patterns or change them to useful patterns (fault dropping). In this paper, we reseed, modify the pseudo-random, and use an additional bit counter to improve test length and achieve high fault coverage. The fact is that a random test set contains useless patterns, so we present a technique, including both reseeding and bit modifying to remove useless patterns or change them to useful patterns, and when the patterns change, we pick out the numbers with less bits, leading to very short test length. The technique we present is applicable for single-stuck-at faults. The seeds we use are deterministic so 100% fault coverage can be achieve.[[conferencetype]]國際[[conferencedate]]20050523~20050526[[booktype]]紙本[[conferencelocation]]Kobe, Japa

Design and Testing of High Speed Multipliers by using Reversible Liner Feedback Shift Register

In recent designs of IC’s (Integrated Circuits) BIST (Built-In Self-Test) is becoming vital for memory where memory is essential part of SoC (System on Chip). BIST design technique allows circuit for self testing. A technique may provide the short test-time as compared to test which applied externally and it allows a use of the low cost test instruments throughout the all production stages. Because of LFSRs randomness properties, it requires less hardware overhead. In particular dissertation, optimization and structure design of BIST design is based on the Reversible LFSRs, which are described. As well Reversible LFSR and Proposed LT LFSR are used to design and test Architecture of different Multipliers such as Array Multipliers and Booth Multiplier

Design of a Scan Chain for Side Channel Attacks on AES Cryptosystem for Improved Security

Scan chain-based attacks are side-channel attacks focusing on one of the most significant features of hardware test circuitry. A technique called Design for Testability (DfT) involves integrating certain testability components into a hardware design. However, this creates a side channel for cryptanalysis, providing crypto devices vulnerable to scan-based attacks. Advanced Encryption Standard (AES) has been proven as the most powerful and secure symmetric encryption algorithm announced by USA Government and it outperforms all other existing cryptographic algorithms. Furthermore, the on-chip implementation of private key algorithms like AES has faced scan-based side-channel attacks. With the aim of protecting the data for secure communication, a new hybrid pipelined AES algorithm with enhanced security features is implemented. This paper proposes testing an AES core with unpredictable response compaction and bit level-masking throughout the scan chain process. A bit-level scan flipflop focused on masking as a scan protection solution for secure testing. The experimental results show that the best security is provided by the randomized addition of masked scan flipflop through the scan chain and also provides minimal design difficulty and power expansion overhead with some negligible delay measures. Thus, the proposed technique outperforms the state-of-the-art LUT-based S-box and the composite sub-byte transformation model regarding throughput rate 2 times and 15 times respectively. And security measured in the avalanche effect for the sub-pipelined model has been increased up to 95 per cent with reduced computational complexity. Also, the proposed sub-pipelined S-box utilizing a composite field arithmetic scheme achieves 7 per cent area effectiveness and 2.5 times the hardware complexity compared to the LUT-based model

A Hardware Security Solution against Scan-Based Attacks

Scan based Design for Test (DfT) schemes have been widely used to achieve high fault coverage for integrated circuits. The scan technique provides full access to the internal nodes of the device-under-test to control them or observe their response to input test vectors. While such comprehensive access is highly desirable for testing, it is not acceptable for secure chips as it is subject to exploitation by various attacks. In this work, new methods are presented to protect the security of critical information against scan-based attacks. In the proposed methods, access to the circuit containing secret information via the scan chain has been severely limited in order to reduce the risk of a security breach. To ensure the testability of the circuit, a built-in self-test which utilizes an LFSR as the test pattern generator (TPG) is proposed. The proposed schemes can be used as a countermeasure against side channel attacks with a low area overhead as compared to the existing solutions in literature

Cellular Automata and Randomization: A Structural Overview

The chapter overviews the methods, algorithms, and architectures for random number generators based on cellular automata, as presented in the scientific literature. The variations in linear and two-dimensional cellular automata model and their features are discussed in relation to their applications as randomizers. Additional memory layers, functional nonuniformity in space or time, and global feedback are examples of such variations. Successful applications of cellular automata random number/signal generators (both software and hardware) reported in the scientific literature are also reviewed. The chapter includes an introductory presentation of the mathematical (ideal) model of cellular automata and its implementation as a computing model, emphasizing some important theoretical debates regarding the complexity and universality of cellular automata

BOOM - A Heuristic Boolean Minimizer

This paper presents an algorithm for two-level Boolean minimization (BOOM) based on a new implicant generation paradigm. In contrast to all previous minimization methods, where the implicants are generated bottom-up, the proposed method uses a top-down approach. Thus, instead of increasing the dimensionality of implicants by omitting literals from their terms, the dimension of a term is gradually decreased by adding new literals. The method is advantageous especially for functions with many input variables (up to thousands) and with only few care terms defined, where other minimization tools are not applicable because of the long runtime. The method has been tested on several different kinds of problems and the results were compared with ESPRESSO

Testability and redundancy techniques for improved yield and reliability of CMOS VLSI circuits

The research presented in this thesis is concerned with the design of fault-tolerant integrated circuits as a contribution to the design of fault-tolerant systems. The economical manufacture of very large area ICs will necessitate the incorporation of fault-tolerance features which are routinely employed in current high density dynamic random access memories. Furthermore, the growing use of ICs in safety-critical applications and/or hostile environments in addition to the prospect of single-chip systems will mandate the use of fault-tolerance for improved reliability. A fault-tolerant IC must be able to detect and correct all possible faults that may affect its operation. The ability of a chip to detect its own faults is not only necessary for fault-tolerance, but it is also regarded as the ultimate solution to the problem of testing. Off-line periodic testing is selected for this research because it achieves better coverage of physical faults and it requires less extra hardware than on-line error detection techniques. Tests for CMOS stuck-open faults are shown to detect all other faults. Simple test sequence generation procedures for the detection of all faults are derived. The test sequences generated by these procedures produce a trivial output, thereby, greatly simplifying the task of test response analysis. A further advantage of the proposed test generation procedures is that they do not require the enumeration of faults. The implementation of built-in self-test is considered and it is shown that the hardware overhead is comparable to that associated with pseudo-random and pseudo-exhaustive techniques while achieving a much higher fault coverage through-the use of the proposed test generation procedures. The consideration of the problem of testing the test circuitry led to the conclusion that complete test coverage may be achieved if separate chips cooperate in testing each other's untested parts. An alternative approach towards complete test coverage would be to design the test circuitry so that it is as distributed as possible and so that it is tested as it performs its function. Fault correction relies on the provision of spare units and a means of reconfiguring the circuit so that the faulty units are discarded. This raises the question of what is the optimum size of a unit? A mathematical model, linking yield and reliability is therefore developed to answer such a question and also to study the effects of such parameters as the amount of redundancy, the size of the additional circuitry required for testing and reconfiguration, and the effect of periodic testing on reliability. The stringent requirement on the size of the reconfiguration logic is illustrated by the application of the model to a typical example. Another important result concerns the effect of periodic testing on reliability. It is shown that periodic off-line testing can achieve approximately the same level of reliability as on-line testing, even when the time between tests is many hundreds of hours