Top-Down Behavioral Modeling Methodology of a Piezoelectric Microgenerator For Integrated Power Harvesting Systems

In this study, we developed a top/down methodology for behavioral and structural modeling of multi-domain microsystems. Then, we validated this methodology through a study case : a piezoelectric microgenerator. We also proved the effectiveness of VHDL-AMS language not only for modeling in behavioral and structural levels but also in writing physical models that can predict the experimental results. Finally, we validated these models by presenting and discussing simulations results.Comment: Submitted on behalf of EDA Publishing Association (http://irevues.inist.fr/handle/2042/16838

SUSTAINABLE ENERGY HARVESTING TECHNOLOGIES – PAST, PRESENT AND FUTURE

Chapter 8: Energy Harvesting Technologies: Thick-Film Piezoelectric Microgenerato

Mini Wind Harvester and a Low Power Three-Phase AC/DC Converter to Power IoT Devices: Analysis, Simulation, Test and Design

Wind energy harvesting is a widespread mature technology employed to collect energy, but it is also suitable, and not yet fully exploited at small scale, for powering low power electronic systems such as Internet of Things (IoT) systems like structural health monitoring, on-line sensors, predictive maintenance, manufacturing processes and surveillance. The present work introduces a three-phase mini wind energy harvester and an Alternate Current/Direct Current (AC/DC) converter. The research analyzes in depth a wind harvester’s operation principles in order to extract its characteristic parameters. It also proposes an equivalent electromechanical model of the harvester, and its accuracy has been verified with prototype performance results. Moreover, unlike most of the converters which use two steps for AC/DC signal conditioning—a rectifier stage and a DC/DC regulator—this work proposes a single stage converter to increase the system efficiency and, consequently, improve the energy transfer. Moreover, the most suitable AC/DC converter architecture was chosen and optimized for the best performance taking into account: the target power, efficiency, voltage levels, operation frequency, duty cycle and load required to implement the aforementioned converter

Micro-mechanical sensor for the spectral decomposition of acoustic signals

An array of electret-biased frequency-selective resonant microelectromechanical system (MEMS) acoustic sensors was proposed to perform analysis of stress pulses created during an impact between two materials. This analysis allowed classification of the stiffness of the materials involved in the impact without applying post-impact signal processing. Arrays of resonant MEMS sensors provided filtering of the incident stress pulse and subsequent binning of time-domain waveforms into frequency-based spectra. Results indicated that different impact conditions and materials yielded different spectral characteristics. These characteristics, as well as the resulting sensor array responses, are discussed and applied to impact classification. Each individual sensor element in the array was biased by an in situ charged electret film. A microplasma discharge apparatus embedded within the microsensor allowed charging of the electret film after all device fabrication was complete. This enabled electret film integration using high-temperature surface micromachining processes that would typically lead to discharge of traditionally formed electret materials. This also eliminated the traditional wafer-bonding and post-fabrication assembly processes required in conventional electret integration approaches. The microplasma discharge process and resulting electret performance are discussed within the context of the MEMS acoustic sensor array.Ph.D.Committee Chair: Allen, Mark; Committee Member: Brand, Oliver; Committee Member: Michaels, Jennifer; Committee Member: Michaels, Thomas; Committee Member: Ready, Jud W

Study, optimization and silicon implementation of a smart high-voltage conditioning circuit for electrostatic vibration energy harvesting system

La récupération de l'énergie des vibrations est un concept relativement nouveau qui peut être utilisé dans l'alimentation des dispositifs embarqués de puissance à micro-échelle avec l'énergie des vibrations omniprésentes dans l environnement. Cette thèse contribue à une étude générale des récupérateurs de l'énergie des vibrations (REV) employant des transducteurs électrostatiques. Un REV électrostatique typique se compose d'un transducteur capacitif, de l'électronique de conditionnement et d un élément de stockage. Ce travail se concentre sur l'examen du circuit de conditionnement auto-synchrone proposé en 2006 par le MIT, qui combine la pompe de charge à base de diodes et le convertisseur DC-DC inductif de type de flyback qui est entraîné par le commutateur. Cette architecture est très prometteuse car elle élimine la commande de grille précise des transistors utilisés dans les architectures synchrones, tandis qu'un commutateur unique se met en marche rarement. Cette thèse propose une analyse théorique du circuit de conditionnement. Nous avons développé un algorithme qui par commutation appropriée de flyback implémente la stratégie de conversion d'énergie optimale en tenant compte des pertes liées à la commutation. En ajoutant une fonction de calibration, le système devient adaptatif pour les fluctuations de l'environnement. Cette étude a été validée par la modélisation comportementale.Une autre contribution consiste en la réalisation de l'algorithme proposé au niveau du circuit CMOS. Les difficultés majeures de conception étaient liées à l'exigence de haute tension et à la priorité de la conception faible puissance. Nous avons conçu un contrôleur du commutateur haute tension de faible puissance en utilisant la technologie AMS035HV. Sa consommation varie entre quelques centaines de nanowatts et quelques microwatts, en fonction de nombreux facteurs - paramètres de vibrations externes, niveaux de tension de la pompe de charge, la fréquence de la commutation de commutateur, la fréquence de la fonction de calibration, etc.Nous avons également réalisé en silicium, fabriqué et testé un commutateur à haute tension avec une nouvelle architecture de l'élévateur de tension de faible puissance. En montant sur des composants discrets de la pompe de charge et du circuit de retour et en utilisant l'interrupteur conçu, nous avons caractérisé le fonctionnement large bande haute-tension du prototype de transducteur MEMS fabriqué à côté de cette thèse à l'ESIEE Paris. Lorsque le capteur est excité par des vibrations stochastiques ayant un niveau d'accélération de 0,8 g rms distribué dans la bande 110-170 Hz, jusqu'à 0,75 W de la puissance nette a été récupérée.Vibration energy harvesting is a relatively new concept that can be used in powering micro-scale power embedded devices with the energy of vibrations omnipresent in the surrounding. This thesis contributes to a general study of vibration energy harvesters (VEHs) employing electrostatic transducers. A typical electrostatic VEH consists of a capacitive transducer, conditioning electronics and a storage element. This work is focused on investigations of the reported by MIT in 2006 auto-synchronous conditioning circuit, which combines the diode-based charge pump and the inductive flyback energy return driven by the switch. This architecture is very promising since it eliminates precise gate control of transistors employed in synchronous architectures, while a unique switch turns on rarely. This thesis addresses the theoretical analysis of the conditioning circuit. We developed an algorithm that by proper switching of the flyback allows the optimal energy conversion strategy taking into account the losses associated with the switching. By adding the calibration function, the system became adaptive to the fluctuations in the environment. This study was validated by the behavioral modeling. Another contribution consists in realization of the proposed algorithm on the circuit level. The major design difficulties were related to the high-voltage requirement and the low-power design priority. We designed a high-voltage analog controller of the switch using AMS035HV technology. Its power consumption varies between several hundred nanowatts and a few microwatts, depending on numerous factors - parameters of external vibrations, voltage levels of the charge pump, frequency of the flyback switching, frequency of calibration function, etc. We also implemented on silicon, fabricated and tested a high-voltage switch with a novel low power level-shifting driver. By mounting on discrete components the charge pump and flyback circuit and employing the proposed switch, we characterized the wideband high-voltage operation of the MEMS transducer prototype fabricated alongside this thesis in ESIEE Paris. When excited with stochastic vibrations having an acceleration level of 0.8 g rms distributed in the band 110-170 Hz, up to 0.75 $\mu$W of net electrical power has been harvested.PARIS-JUSSIEU-Bib.électronique (751059901) / SudocSudocFranceF

Wideband vibration energy harvesting using electromagnetic transduction for powering internet of things

The ‘Internet of Things-(IoT)’ envisions a world scattered with physical sensors that collect and transmit data about almost anything and thereby enabling intelligent decision-making for a smart environment. While technological advancements have reduced the power consumption of such devices significantly, the problem of perpetual energy supply beyond the limited capability of batteries is a bottleneck to this vision which is yet to be resolved. This issue has surged the research to investigate the prospect of harvesting the energy out of ambient mechanical vibrations. However, limited applications of conventional resonant devices under most practical environments involving frequency varying inputs, has gushed the research on wideband transducers recently. To facilitate multi-frequency operation at low-frequency regime, design innovations of the Silicon-onInsulator based MEMS suspension systems are performed through multi-modal activation. For continuous bandwidth widening, the benefits of using nonlinear stiffness in the system dynamics are investigated. By topologically varying the spring architectures, dramatically improved operational bandwidth with large power-density is obtained, which is benchmarked using a novel figure-of-merit. However, the fundamental phenomenon of multi-stability limits many nonlinear oscillator based applications including energy harvesting. To address this, an electrical control mechanism is introduced which dramatically improves the energy conversion efficiency over a wide bandwidth in a frequencyamplitude varying environment using only a small energy budget. The underlying effects are independent of the device-scale and the transduction methods, and are explained using a modified Duffing oscillator model. One of the key requirements for fully integrated electromagnetic transducers is the CMOS compatible batch-fabrication of permanent magnets with large energy-product. In the final module of the works, nano-structured CoPtP hard-magnetic material with large coercivity is developed at room-temperature using a current modulated electro-deposition technique. The demagnetization fields of the magnetic structures are minimized through optimized micro-patterns which enable the full integration of high performance electromagnetic energy harvesters

Enabling and Understanding Failure of Engineering Structures Using the Technique of Cohesive Elements

In this paper, we describe a cohesive zone model for the prediction of failure of engineering solids and/or structures. A damage evolution law is incorporated into a three-dimensional, exponential cohesive law to account for material degradation under the influence of cyclic loading. This cohesive zone model is implemented in the finite element software ABAQUS through a user defined subroutine. The irreversibility of the cohesive zone model is first verified and subsequently applied for studying cyclic crack growth in specimens experiencing different modes of fracture and/or failure. The crack growth behavior to include both crack initiation and crack propagation becomes a natural outcome of the numerical simulation. Numerical examples suggest that the irreversible cohesive zone model can serve as an efficient tool to predict fatigue crack growth. Key issues such as crack path deviation, convergence and mesh dependency are also discussed

Sistemas eficientes de transmissão de energia sem-fios e identificação por radiofrequência

Doutoramento em Engenharia EletrotécnicaIn the IoT context, where billions of connected objects are expected to be ubiquitously deployed worldwide, the frequent battery maintenance of ubiquitous wireless nodes is undesirable or even impossible. In these scenarios, passive-backscatter radios will certainly play a crucial role due to their low cost, low complexity and battery-free operation. However, as passive-backscatter devices are chiefly limited by the WPT link, its efficiency optimization has been a major research concern over the years, gaining even more emphasis in the IoT context. Wireless power transfer has traditionally been carried out using CW signals, and the efficiency improvement has commonly been achieved through circuit design optimization. This thesis explores a fundamentally different approach, in which the optimization is focused on the powering waveforms, rather than the circuits. It is demonstrated through theoretical analysis, simulations and measurements that, given their greater ability to overcome the built-in voltage of rectifying devices, high PAPR multi-sine (MS) signals are capable of more efficiently exciting energy harvesting circuits when compared to CWs. By using optimal MS signals to excite rectifying devices, remarkable RF-DC conversion efficiency gains of up to 15 dB with respect to CW signals were obtained. In order to show the effectiveness of this approach to improve the communication range of passive-backscatter systems, a MS front-end was integrated in a commercial RFID reader and a significant range extension of 25% was observed. Furthermore, a software-defined radio RFID reader, compliant with ISO18000-6C standard and with MS capability, was constructed from scratch. By interrogating passive RFID transponders with MS waveforms, a transponder sensitivity improvement higher than 3 dB was obtained for optimal MS signals. Since the amplification and transmission of high PAPR signals is critical, this work also proposes efficient MS transmitting architectures based on space power combining techniques. This thesis also addresses other not less important issues, namely self-jamming in passive RFID readers, which is the second limiting factor of passive-backscatter systems. A suitable self-jamming suppression scheme was first used for CW signals and then extended to MS signals, yielding a CW isolation up to 50 dB and a MS isolation up 60 dB. Finally, a battery-less remote control system was developed and integrated in a commercial TV device with the purpose of demonstrating a practical application of wireless power transfer and passive-backscatter concepts. This allowed battery-free control of four basic functionalities of the TV (CH+,CH-,VOL+,VOL-).No contexto da internet das coisas (IoT), onde são esperados bilhões de objetos conectados espalhados pelo planeta de forma ubíqua, torna-se impraticável uma frequente manutenção e troca de baterias dos dispositivos sem fios ubíquos. Nestes cenários, os sistemas radio backscatter passivos terão um papel preponderante dado o seu baixo custo, baixa complexidade e não necessidade de baterias nos nós móveis. Uma vez que a transmissão de energia sem fios é o principal aspeto limitativo nestes sistemas, a sua otimização tem sido um tema central de investigação, ganhando ainda mais ênfase no contexto IoT. Tradicionalmente, a transferência de energia sem-fios é feita através de sinais CW e a maximização da eficiência é conseguida através da otimização dos circuitos recetores. Neste trabalho explora-se uma abordagem fundamentalmente diferente, em que a otimização foca-se nas formas de onda em vez dos circuitos. Demonstra-se, teoricamente e através de simulações e medidas que, devido à sua maior capacidade em superar a barreira de potencial intrínseca dos dispositivos retificadores, os sinais multi-seno (MS) de elevado PAPR são capazes de excitar os circuitos de colheita de energia de forma mais eficiente quando comparados com o sinal CW tradicional. Usando sinais MS ótimos em circuitos retificadores, foram verificadas experimentalmente melhorias de eficiência de conversão RF-DC notáveis de até 15 dB relativamente ao sinal CW. A fim de mostrar a eficácia desta abordagem na melhoria da distância de comunicação de sistemas backscatter passivos, integrou-se um front-end MS num leitor RFID comercial e observou-se um aumento significativo de 25% na distância de leitura. Além disso, desenvolveu-se de raiz um leitor RFID baseado em software rádio, compatível com o protocolo ISO18000-6C e capaz de gerar sinais MS, com os quais interrogou-se transponders passivos, obtendo-se ganhos de sensibilidade dos transponders maiores que 3 dB. Uma vez que a amplificação de sinais de elevado PAPR é uma operação crítica, propôs-se também novas arquiteturas eficientes de transmissão baseadas na combinação de sinais em espaço livre. Esta tese aborda também outros aspetos não menos importantes, como o self-jamming em leitores RFID passivos, tido como o segundo fator limitativo neste tipo de sistemas. Estudou-se técnicas de cancelamento de self-jamming CW e estendeu-se o conceito a sinais MS, tendo-se obtido isolamentos entre o transmissor e o recetor de até 50 dB no primeiro caso e de até 60 dB no segundo. Finalmente, com o objetivo de demonstrar uma aplicação prática dos conceitos de transmissão de energia sem fios e comunicação backscatter, desenvolveu-se um sistema de controlo remoto sem pilhas, cujo protótipo foi integrado num televisor comercial a fim de controlar quatro funcionalidades básicas (CH+,CH-,VOL+,VOL-)