SLIP: 10 years ago and 10 years from now

Founded in 1999, the ACM SLIP Workshop is now in its 12th year. The 2010 SLIP Panel session will highlight perspectives from three individuals who have had great influence on the course of SLIP, and provide an opportunity for lively discussion by workshop attendees of prospects for the next 10 years of SLIP. This panel summary records preliminary thoughts of the panelists on two starting questions

Crosstalk minimization of local channel routing algorithms in VLSI CAD

The greedy and left edge algorithms, as applied to local routing in VLSI CAD, were modified to decrease crosstalk between neighboring wires. The modifications on the algorithms use spacing, and segregation to improve the routing of wires in a channel. The modified greedy and left edge algorithms use a grid, but the minimum distance between two wires can be varied depending on the crosstalk between them. Crosstalk information must be obtained separately and is part of the required set of inputs to the algorithms. The improved algorithms route all the channel problems tested in less tracks than the original algorithms, if crosstalk constraints exist, and in the same number of tracks, if no crosstalk constraints exist

Implementation of Static and Semi-Static Versions of a 24+8x8 Quad-rail NULL Convention Multiply and Accumulate Unit

This paper focuses on implementing a 2s complement 8x8 dual-rail bit-wise pipelined multiplier using the asynchronous null convention logic (NCL) paradigm. The design utilizes a Wallace tree for partial product summation, and is implemented and simulated in VHDL, the transistor level, and the physical level, using a 1.8V 0.18mum TSMC CMOS process. The multiplier is realized using both static and semi-static versions of the NCL gates; and these two implementations are compared in terms of area, power, and speed

A Framework for the Detection of Crosstalk Noise in FPGAs

In recent years, crosstalk noise has emerged a serious problem because more and more devices and wires have been packed on electronic chips. As integrated circuits are migrated to more advanced technologies, it has become clear that crosstalk noise is the important phenomenon that must be taken into account. Despite of being more immune to crosstalk noise than their ASIC (application specific integrated circuit) counterparts, the dense interconnected structures of FPGAs (field programmable gate arrays) invite more vulnerabilities with crosstalk noise. Due to the lack of electrical detail concerning FPGA devices it is quite difficult to test the faults affected by crosstalk noise. This paper proposes a new approach for detecting the effects such as glitches and delays in transition that are due to crosstalk noise in FPGAs. This approach is similar to the BIST (built-in self test) technique in that it incorporates the test pattern generator to generate the test vectors and the analyzer to analyze the crosstalk faults without any overhead for testing

Study Of The Relationship Between Delta Delay And Adjacent Parallel Wire Length In 45 Nanometer Process Technology

Hierarchical design spans the complete framework of a design flow from Register Transfer Level (RTL), synthesis, place and route, timing closure and various other analyses before sign-off. Finer geometries and increasing interconnect density however have resulted signal integrity becoming the key issue for Deep Sub-Micron design. Post silicon bug due to noise and signal integrity can be prevented and fixed at early stage of the IC design cycle. The purpose of this research is to establish a preventive measurement for adjacent wire that can travel in parallel for 45nm technology. The intention is to ensure that a complex design can be delivered to the market with accurate, fast and trusted analysis and provide sign-off solution. Main approach is to conduct the relationship study between delta delay and adjacent parallel wire in 45 nanometer (nm) process technology and provide a preventive measurement to limit the adjacent wire can travel in parallel. The design is explored thoroughly to study the relationship between delay noise and adjacent parallel wire. The correlation is translated into an equation to estimate the delay noise produced with a certain length of adjacent parallel wire

Low-Power, High-Speed Transceivers for Network-on-Chip Communication

Networks on chips (NoCs) are becoming popular as they provide a solution for the interconnection problems on large integrated circuits (ICs). But even in a NoC, link-power can become unacceptably high and data rates are limited when conventional data transceivers are used. In this paper, we present a low-power, high-speed source-synchronous link transceiver which enables a factor 3.3 reduction in link power together with an 80% increase in data-rate. A low-swing capacitive pre-emphasis transmitter in combination with a double-tail sense-amplifier enable speeds in excess of 9 Gb/s over a 2 mm twisted differential interconnect, while consuming only 130 fJ/transition without the need for an additional supply. Multiple transceivers can be connected back-to-back to create a source-synchronous transceiver-chain with a wave-pipelined clock, operating with 6sigma offset reliability at 5 Gb/s

Course grained low power design flow using UPF

Increased system complexity has led to the substitution of the traditional bottom-up design flow by systematic hierarchical design flow. The main motivation behind the evolution of such an approach is the increasing difficulty in hardware realization of complex systems. With decreasing channel lengths, few key problems such as timing closure, design sign-off, routing complexity, signal integrity, and power dissipation arise in the design flows. Specifically, minimizing power dissipation is critical in several high-end processors. In high-end processors, the design complexity contributes to the overall dynamic power while the decreasing transistor size results in static power dissipation. This research aims at optimizing the design flow for power and timing using the unified power format (UPF). UPF provides a strategic format to specify power-aware design information at every stage in the flow. The low power reduction techniques enforced in this research are multi-voltage, multi-threshold voltage (Vth), and power gating with state retention. An inherent design challenge addressed in this research is the choice of power optimization techniques as the flow advances from synthesis to physical design. A top-down digital design flow for a 32 bit MIPS RISC processor has been implemented with and without UPF synthesis flow for 65nm technology. The UPF synthesis is implemented with two voltages, 1.08V and 0.864V (Multi-VDD). Area, power and timing metrics are analyzed for the flows developed. Power savings of about 20 % are achieved in the design flow with \u27multi-threshold\u27 power technique compared to that of the design flow with no low power techniques employed. Similarly, 30 % power savings are achieved in the design flow with the UPF implemented when compared to that of the design flow with \u27multi-threshold\u27 power technique employed. Thus, a cumulative power savings of 42% has been achieved in a complete power efficient design flow (UPF) compared to that of the generic top-down standard flow with no power saving techniques employed. This is substantiated by the low voltage operation of modules in the design, reduction in clock switching power by gating clocks in the design and extensive use of HVT and LVT standard cells for implementation. The UPF synthesis flow saw the worst timing slack and more area when compared to those of the `multi-threshold\u27 or the generic flow. Percentage increase in the area with UPF is approximately 15%; a significant source for this increase being the additional power controlling logic added